- 您現在的位置：買賣IC網 > PDF目錄1989 > ADF4360-9BCPZ (Analog Devices Inc)IC SYNTHESIZER W/ADJ VCO 24LFCSP PDF資料下載
參數資料
| 型號： | ADF4360-9BCPZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 10/24頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC SYNTHESIZER W/ADJ VCO 24LFCSP |
| 標準包裝： | 1 |
| 類型： | 扇出配送，整數-N，合成器（RF） |
| PLL： | 是 |
| 輸入： | CMOS，TTL |
| 輸出： | 時鐘 |
| 電路數： | 1 |
| 比率 - 輸入:輸出： | 1:2 |
| 差分 - 輸入:輸出： | 無/無 |
| 頻率 - 最大： | 400MHz |
| 除法器/乘法器： | 是/無 |
| 電源電壓： | 3 V ~ 3.6 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 24-VFQFN 裸露焊盤，CSP |
| 供應商設備封裝： | 24-LFCSP-VQ（4x4） |
| 包裝： | 托盤 |
ADF4360-9
Data Sheet
Rev. C | Page 18 of 24
Software Power-Up/Power-Down
If the part is powered down via the software (using the control
latch) and powered up again without any change to the N counter
latch during power-down, the part locks at the correct frequency
because the part is already in the correct frequency band. The
lock time depends on the value of capacitance on the CN pin,
which is <15 ms for 10 F capacitance. The smaller capacitance
of 440 nF on this pin enables lock times of <600 s.
The N counter value cannot be changed while the part is in
power-down because the part may not lock to the correct
frequency on power-up. If it is updated, the correct program-
ming sequence for the part after power-up is to the R counter
latch, followed by the control latch, and finally the N counter
latch, with the required interval between the control latch and
N counter latch, as described in the Initial Power-Up section.
CONTROL LATCH
With (C2, C1) = (0, 0), the control latch is programmed. Figure 23
shows the input data format for programming the control latch.
Power-Down
DB21 (PD2) and DB20 (PD1) provide programmable power-
down modes.
In the programmed asynchronous power-down, the device
powers down immediately after latching a 1 into Bit PD1, with
the condition that PD2 is loaded with a 0. In the programmed
synchronous power-down, the device power-down is gated by
the charge pump to prevent unwanted frequency jumps. Once
the power-down is enabled by writing a 1 into Bit PD1 (on the
condition that a 1 is also loaded in PD2), the device goes into
power-down on the second rising edge of the R counter output,
after LE goes high. When a power-down is activated (either
synchronous or asynchronous mode), the following events occur:
All active dc current paths are removed.
The R, N, and timeout counters are forced to their load
state conditions.
The charge pump is forced into three-state mode.
The digital lock detect circuitry is reset.
The RF outputs are debiased to a high impedance state.
The reference input buffer circuitry is disabled.
The input register remains active and capable of loading
and latching data.
Charge Pump Currents
CPI3, CPI2, and CPI1 in the ADF4360 family determine
Current Setting 1. CPI6, CPI5, and CPI4 determine Current
Setting 2 (see the truth table in Figure 23).
Output Power Level
Bit PL1 and Bit PL2 set the output power level of the VCO (see
the truth table in Figure 23).
Mute-Till-Lock Detect
DB11 of the control latch in the ADF4360 family is the mute-
till-lock detect bit. This function, when enabled, ensures that
the RF outputs are not switched on until the PLL is locked.
CP Gain
DB10 of the control latch in the ADF4360 family is the charge
pump gain bit. When it is programmed to 1, Current Setting 2
is used. When programmed to 0, Current Setting 1 is used.
Charge Pump Three-State
This bit (DB9) puts the charge pump into three-state mode
when programmed to a 1. For normal operation, it should be
set to 0.
Phase Detector Polarity
The PDP bit in the ADF4360 family sets the phase detector
polarity. The positive setting enabled by programming a 1 is
used when using the on-chip VCO with a passive loop filter or
with an active noninverting filter. It can also be set to 0, which
is required if an active inverting loop filter is used.
DIVOUT Control
The on-chip multiplexer is controlled by D3, D2, and D1 (see
the truth table in Figure 23).
Counter Reset
DB4 is the counter reset bit for the ADF4360 family. When this
is 1, the R counter and the A, B counters are reset. For normal
operation, this bit should be 0.
Core Power Level
PC1 and PC2 set the power level in the VCO core. The
recommended setting is 5 mA. The 7.5 mA setting is
permissible in some applications (see the truth table in Figure 23).
相關PDF資料 |
PDF描述 |
|---|---|
| ADF5000BCPZ-RL7 | IC PRESCALER 18GHZ 16LFCSP |
| ADF5002BCPZ | IC PRESCALER 18GHZ 16LFCSP |
| ADN2804ACPZ | IC CLK/DATA REC 622MBPS 32-LFCSP |
| ADN2805ACPZ-500RL7 | IC CLK/DATA REC 1.25GBPS 32LFCSP |
| ADN2806ACPZ | IC CLK/DATA REC 622MBPS 32-LFCSP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADF4360-9BCPZRL | 功能描述:IC SYNTHESIZER W/ADJ VCO 24LFCSP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘發生器，PLL，頻率合成器 系列:- 標準包裝:1,000 系列:Precision Edge® 類型:時鐘/頻率合成器 PLL:無 輸入:CML，PECL 輸出:CML 電路數:1 比率 - 輸入:輸出:2:1 差分 - 輸入:輸出:是/是 頻率 - 最大:10.7GHz 除法器/乘法器:無/無 電源電壓:2.375 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-VFQFN 裸露焊盤，16-MLF? 供應商設備封裝:16-MLF?（3x3） 包裝:帶卷 (TR) 其它名稱:SY58052UMGTRSY58052UMGTR-ND |
| ADF4360-9BCPZRL7 | 功能描述:IC SYNTHESIZER W/ADJ VCO 24LFCSP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘發生器，PLL，頻率合成器 系列:- 標準包裝:2,000 系列:- 類型:PLL 頻率合成器 PLL:是 輸入:晶體 輸出:時鐘 電路數:1 比率 - 輸入:輸出:1:1 差分 - 輸入:輸出:無/無 頻率 - 最大:1GHz 除法器/乘法器:是/無 電源電壓:4.5 V ~ 5.5 V 工作溫度:-20°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-LSSOP（0.175"，4.40mm 寬） 供應商設備封裝:16-SSOP 包裝:帶卷 (TR) 其它名稱:NJW1504V-TE1-NDNJW1504V-TE1TR |
| ADF4360-EVAL | 制造商:Analog Devices 功能描述:INTEGRATED SYNTHESIZER AND VCO - Trays |
| ADF4602 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Single-Chip, Multiband 3G Femtocell Transceiver |
| ADF4602-1XCPZ | 制造商:Analog Devices 功能描述:SINGLE-CHIP, MULTIBAND 3G FEMTOCELL TRANSCEIVER - Rail/Tube |
發布緊急采購，3分鐘左右您將得到回復。