VCM SLICER_LEVEL 50k V
參數資料
型號： ADAU1590ACPZ-RL
廠商： Analog Devices Inc
文件頁數： 8/24頁
文件大小： 0K
描述： IC AMP AUDIO PWR 15.5W 48LFCSP
產品變化通告： ADAU1513,1590 Discontinuation 09/Apr/2012
標準包裝： 2,500
類型： D 類
輸出類型： 2 通道（立體聲）
在某負載時最大輸出功率 x 通道數量： 15.5W x 2 @ 4 歐姆
電源電壓： 9 V ~ 15 V
特點： 消除爆音，靜音，短路和熱保護
安裝類型： 表面貼裝
供應商設備封裝： 48-LFCSP-VQ（7x7）
封裝/外殼： 48-VFQFN 裸露焊盤，CSP
包裝： 帶卷 (TR)
ADAU1590
Rev. 0 | Page 16 of 24
06
67
3-
04
0
VCM
SLICER_LEVEL
50k
VTH
PIN 24 (SLC_TH)
REXTERNAL
Figure 40. Block for Slicer Threshold Adjust, SLC_TH
The slicer threshold can be set externally using a resistor as
follows:
VTH = (AVDD/2) × (50 kΩ/50 kΩ + REXTERNAL)
where:
AVDD = 3.3 V typical.
VTH is the voltage threshold at which the slicer is activated.
The following equation can be used to calculate the input signal
at which the slicer becomes active:
0.9
1.414 ×
=
TH
IN RMS
V
Therefore, for AVDD = 3.3 V typical and VTH = 1.1 V,
REXTERNAL = 24.9 kΩ
VIN RMS = 0.864 V
Thus, the slicer is activated at and above 0.864 VIN RMS.
This feature allows the user to set the slicer and, in turn, reduces
the output power at a given supply voltage.To disable the slicer,
SLC_TH should be connected to AGND. Table 9 shows the
typical values for REXTERNAL.
Table 9. Typical REXTERNAL Values
VTH (V)
REXTERNAL (kΩ)
VIN RMS (V)
1.1
24.9
0.864
1.17
20.5
0.919
1.24
16.5
0.974
1.32
12.4
1.037
POWER STAGE
The ADAU1590 power stage comprises a high-side PMOS and
a low-side NMOS. The typical RDS-ON is ~300 mΩ. The PMOS-
NMOS stage does not need an external bootstrap capacitor and
simplifies the high-side driver design. The power stage also has
comprehensive protection circuits to detect the faults in typical
applications. See the Protection Circuits section for further details.
GAIN
The gain of the amplifier is set internally using feedback resis-
tors optimized for 12 V nominal operation. The typical gain
values are tabulated in Table 1. The typical gain is 17 dB with
PGA set to 0 dB. PGA0 (Pin 14) and PGA1 (Pin 13) are used
for setting the desired gain.
The gain can be set according to Table 10. Note that the ampli-
fier full-scale input level changes as per the PGA gain setting.
Table 10. Gain Settings
PGA1
(Pin 13)
PGA0
(Pin14)
PGA
Gain (dB)
Amplifier
Gain (dB)
Full-Scale
Input Level
(VRMS)
0
17
1
0
1
6
23
0.5
1
0
12
29
0.25
1
18
35
0.125
PROTECTION CIRCUITS
The ADAU1590 includes comprehensive protection circuits. It
includes thermal warning, thermal overheat, and overcurrent or
short-circuit protection on the outputs. The ERR and OTW
outputs are open drain and require external pull-up resistors.
The outputs are capable of sinking 10 mA. The open-drain
outputs are useful in multichannel applications where more
than one ADAU1590 is used. The error outputs of multiple
ADAU1590s can be OR’ed to simplify the system design.
The logic outputs of the error flags ease the system design of
using a microcontroller.
THERMAL PROTECTION
Thermal protection in the ADAU1590 is categorized into two
error flags: one as thermal warning and the other as thermal
shutdown. When the device junction temperature reaches near
135°C (±5°C), the ADAU1590 outputs a thermal warning error
flag by pulling OTW (Pin 10) low. This flag can be used by the
microcontroller in the system for indication to the user or can
be used to lower the input level to the amplifier to prevent
thermal shutdown. The device continues operation until
shutdown temperature is reached.
When the device junction temperature exceeds 150°C, the
device outputs an error flag by pulling ERR (Pin 9) low. This
error flag is latched. To restore the operation, MUTE (Pin 15)
needs to be toggled to low and then to high again.
OVERCURRENT PROTECTION
The overcurrent protection in the ADAU1590 is set internally at
a 5 A peak output current. The device protects the output
devices against excessive output current by pulling ERR (Pin 9)
low. This error flag is latched. To restore the normal operation,
MUTE (Pin 15) needs to be toggled to low and then to high
again. The error flag is useful for the microcontroller in the
system to indicate abnormal operation and to initiate the audio
MUTE sequence. The device senses the short-circuit condition
相關PDF資料
PDF描述
VI-244-IU-S CONVERTER MOD DC/DC 48V 200W
ADAU1513ACPZ-RL IC AMP AUDIO PWR 23W 48LFCSP
VE-24H-IU-S CONVERTER MOD DC/DC 52V 200W
ADAU1513ACPZ IC AMP AUDIO PWR 23W 48LFCSP
VE-24F-IU-S CONVERTER MOD DC/DC 72V 200W
相關代理商/技術參數
參數描述
ADAU1590ACPZ-RL7 功能描述:IC AMP AUDIO PWR 48LFCSP RoHS:是 類別:集成電路 (IC) >> 線性 - 音頻放大器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:DirectDrive® 類型:H 類 輸出類型:耳機，2-通道（立體聲） 在某負載時最大輸出功率 x 通道數量:35mW x 2 @ 16 歐姆 電源電壓:1.62 V ~ 1.98 V 特點:I²C，麥克風，靜音，短路保護，音量控制 安裝類型:表面貼裝 供應商設備封裝:25-WLP（2.09x2.09） 封裝/外殼:25-WFBGA，WLCSP 包裝:帶卷 (TR)
ADAU1590ASVZ 制造商:Analog Devices 功能描述:
ADAU1590ASVZ-RL 制造商:AD 制造商全稱:Analog Devices 功能描述:Class-D Audio Power Amplifier
ADAU1590ASVZRL7 制造商:AD 制造商全稱:Analog Devices 功能描述:Class-D Audio Power Amplifier
ADAU1592 制造商:AD 制造商全稱:Analog Devices 功能描述:Class-D Audio Power Amplifier
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*