- 您現在的位置：買賣IC網 > PDF目錄165344 > ADAU1382BCPZ-R7 (ANALOG DEVICES INC) SPECIALTY CONSUMER CIRCUIT, PQCC32 PDF資料下載
參數資料
| 型號： | ADAU1382BCPZ-R7 |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 消費家電 |
| 英文描述： | SPECIALTY CONSUMER CIRCUIT, PQCC32 |
| 封裝： | 5 X 5 MM, ROHS COMPLIANT, MO-220VHHD2, LFCSP-32 |
| 文件頁數： | 30/84頁 |
| 文件大小： | 1193K |
| 代理商： | ADAU1382BCPZ-R7 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁當前第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁
ADAU1382
Rev. 0 | Page 36 of 84
SPI PORT
By default, the ADAU1382 is in I2C mode, but can be put into SPI
control mode by pulling CLATCH low three times. The SPI port
uses a 4-wire interface, consisting of CLATCH, CCLK, CDATA,
and COUT signals, and is always a slave port. The CLATCH signal
goes low at the beginning of a transaction and high at the end of
a transaction. The CCLK signal latches CDATA on a low-to-high
transition. COUT data is shifted out of the ADAU1382 on the
falling edge of CCLK and should be clocked into a receiving
device, such as a microcontroller, on the CCLK rising edge. The
CDATA signal carries the serial input data, and the COUT signal is
the serial output data. The COUT signal remains three-stated until
a read operation is requested. This allows other SPI-compatible
peripherals to share the same readback line. All SPI transactions
have the same basic format shown in
. A timing diagram
is shown in
. All data should be written MSB first. The
ADAU1382 can be taken out of SPI mode only by a full reset.
Chip Address R/W
The first byte of an SPI transaction includes the 7-bit chip address
and an R/W bit. The chip address is always 0x38. The LSB of
this first byte determines whether the SPI transaction is a read
(Logic 1) or a write (Logic 0).
Table 23. SPI Address Byte Format
Bit 0
Bit 1
Bit 2
Bit 3
Bit 4
Bit 5
Bit 6
Bit 7
0
1
0
R/W
Subaddress
The 12-bit subaddress word is decoded into a location in one of
the registers. This subaddress is the location of the appropriate
register. The MSBs of the subaddress are zero-padded to bring the
word to a full 2-byte length.
Data Bytes
The number of data bytes varies according to the register being
accessed. During a burst mode write, an initial subaddress is
written followed by a continuous sequence of data for consecutive
register locations. A sample timing diagram for a single-write
SPI operation to the parameter memory is shown in Figure 43.
A sample timing diagram of a single-read SPI operation is shown
in Figure 44. The COUT pin goes from three-state to being driven
at the beginning of Byte 3. In this example, Byte 0 to Byte 2
contain the addresses and R/W bit, and subsequent bytes carry
the data.
SPI Read/Write Clock Frequency (CCLK)
The SPI port of the ADAU1382 has asymmetrical read and
write clock frequencies. It is possible to write data into the
device at higher data rates than reading data out of the device.
More detailed information is available in the Digital Timing
Specifications section.
MEMORY AND REGISTER ACCESS
Several conditions must be true to have full access to all memory
and registers via the control port:
The ADAU1382 must have finished its initialization,
including power-on reset, PLL lock, and self-boot.
The core clock must be enabled (Register 16384 (0x4000),
clock control, Bit 0, core clock enable, set to 1).
The memory controller must be powered (Register 16512
(0x4080), Digital Power-Down 0, Bit 6, memory controller, set
to 1).
The sound engine must be powered (Register 16512 (0x4080),
Digital Power-Down 0, Bit 0, sound engine, set to 1).
Table 24. Generic Control Word Format
Byte 0
Byte 1
Byte 2
Byte 3
Byte 41
CHIP_ADR[6:0], R/W
SUBADR[15:8]
SUBADR[7:0]
Data
1 Continues to end of data.
相關PDF資料 |
PDF描述 |
|---|---|
| ADAU1382BCPZ | SPECIALTY CONSUMER CIRCUIT, PQCC32 |
| ADC-00403-103 | 1-CH 12-BIT SUCCESSIVE APPROXIMATION ADC, PARALLEL ACCESS, CDIP32 |
| ADC0831 | A/D Peripherals with Serial Control |
| ADC0831A | A/D Peripherals with Serial Control |
| ADC0831B | A/D Peripherals with Serial Control |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADAU1401 | 制造商:AD 制造商全稱:Analog Devices 功能描述:SigmaDSP 28-/56-Bit Audio Processor with Two ADCs and Four DACs |
| ADAU1401A | 制造商:AD 制造商全稱:Analog Devices 功能描述:SigmaDSP 28-/56-Bit Audio Processor with Two ADCs and Four DACs |
| ADAU1401AWBSTZ | 功能描述:IC AUDIO PROC 28/56BIT 48LQFP RoHS:是 類別:集成電路 (IC) >> 線性 - 音頻處理 系列:SigmaDSP® 其它有關文件:STA321 View All Specifications 標準包裝:1 系列:Sound Terminal™ 類型:音頻處理器 應用:數字音頻 安裝類型:表面貼裝 封裝/外殼:64-LQFP 裸露焊盤 供應商設備封裝:64-LQFP EP（10x10） 包裝:Digi-Reel® 其它名稱:497-11050-6 |
| ADAU1401AWBSTZ-RL | 功能描述:IC AUDIO PROC 28/56BIT 48LQFP RoHS:是 類別:集成電路 (IC) >> 線性 - 音頻處理 系列:SigmaDSP® 其它有關文件:STA321 View All Specifications 標準包裝:1 系列:Sound Terminal™ 類型:音頻處理器 應用:數字音頻 安裝類型:表面貼裝 封裝/外殼:64-LQFP 裸露焊盤 供應商設備封裝:64-LQFP EP（10x10） 包裝:Digi-Reel® 其它名稱:497-11050-6 |
| ADAU1401YSTZ | 功能描述:IC AUDIO PROC 28/56BIT 48LQFP RoHS:是 類別:集成電路 (IC) >> 線性 - 音頻處理 系列:SigmaDSP® 其它有關文件:STA321 View All Specifications 標準包裝:1 系列:Sound Terminal™ 類型:音頻處理器 應用:數字音頻 安裝類型:表面貼裝 封裝/外殼:64-LQFP 裸露焊盤 供應商設備封裝:64-LQFP EP（10x10） 包裝:Digi-Reel® 其它名稱:497-11050-6 |
發布緊急采購，3分鐘左右您將得到回復。