參數資料
型號: ADA4941-1
廠商: Analog Devices, Inc.
英文描述: 16-Bit, +/-0.65 LSB INL, 500 kSPS PulSAR Differential ADC in MSOP/QFN
中文描述: 16位/ -0.65 LSB INL和500 kSPS的PulSAR系列差分ADC,采用MSOP / QFN封裝
文件頁數: 18/24頁
文件大?。?/td> 449K
代理商: ADA4941-1
AD7693
Preliminary Technical Data
CS MODE 3-WIRE WITH BUSY INDICATOR
Rev. PrB | Page 18 of 24
This mode is usually used when a single AD7693 is connected
to an SPI-compatible digital host having an interrupt input.
The connection diagram is shown in Figure 35, and the
corresponding timing is given in Figure 36.
With SDI tied to VIO, a rising edge on CNV initiates a
conversion, selects the CS mode, and forces SDO to high
impedance. SDO is maintained in high impedance until the
completion of the conversion irrespective of the state of CNV.
Prior to the minimum conversion time, CNV can be used to
select other SPI devices, such as analog multiplexers, but CNV
must be returned low before the minimum conversion time
elapses and then held low for the maximum possible conversion
time to guarantee the generation of the busy signal indicator.
When the conversion is complete, SDO goes from high
impedance to low impedance. With a pull-up on the SDO line,
this transition can be used as an interrupt signal to initiate the
data reading controlled by the digital host. The AD7693 then
enters the acquisition phase and powers down. The data bits are
clocked out, MSB first, by subsequent SCK falling edges. The
data is valid on both SCK edges. Although the rising edge can
be used to capture the data, a digital host using the SCK falling
edge will allow a faster reading rate, provided it has an
acceptable hold time. After the optional 17
th
SCK falling edge,
or when CNV goes high, whichever is earlier, SDO returns to
high impedance.
If multiple AD7693s are selected at the same time, the SDO
output pin handles this contention without damage or induced
latch-up. Meanwhile, it is recommended to keep this contention
as short as possible to limit extra power dissipation.
DATA IN
IRQ
CLK
CONVERT
VIO
DIGITAL HOST
CNV
SCK
SDO
SDI
VIO
AD7693
-
CS
Figure 35. 3-Wire
Connection Diagram (SDI High)
Mode with Busy Indicator
SDO
D15
D14
D1
D0
t
DIS
SCK
1
2
3
15
16
17
t
SCK
t
SCKL
t
SCKH
t
HSDO
t
DSDO
CNV
CONVERSION
ACQUISITION
t
CONV
t
CYC
ACQUISITION
SDI = 1
t
CNVH
t
ACQ
-
CS
Figure 36. 3-Wire
Mode with Busy Indicator Serial Interface Timing (SDI High)
相關PDF資料
PDF描述
AD7691 18-Bit, 1.5 LSB INL, 250 kSPS PulSAR Differential ADC in MSOP/QFN
AD7691BRMZ 18-Bit, 1.5 LSB INL, 250 kSPS PulSAR Differential ADC in MSOP/QFN
AD7691BRMZ-RL7 18-Bit, 1.5 LSB INL, 250 kSPS PulSAR Differential ADC in MSOP/QFN
AD7710AN Signal Conditioning ADC
AD7710AQ Signal Conditioning ADC
相關代理商/技術參數
參數描述
ADA4941-1YCP-EBZ 功能描述:BOARD EVAL FOR ADA4941-1YCP RoHS:是 類別:編程器,開發系統 >> 評估板 - 運算放大器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:-
ADA4941-1YCPZ-R2 制造商:Analog Devices 功能描述:SP Amp DIFF Line Driver Amp Single R-R O/P 12V 8-Pin LFCSP EP T/R 制造商:Analog Devices 功能描述:SP Amp DIFF Line Driver Amp Single R-R O/P 12V 8-Pin LFCSP EP Tape & Reel
ADA4941-1YCPZ-R7 功能描述:IC AMP DIFF ADC DVR 18BIT 8LFCSP RoHS:是 類別:集成電路 (IC) >> 線性 - 放大器 - 專用 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:60 系列:- 類型:可變增益放大器 應用:CATV 安裝類型:表面貼裝 封裝/外殼:20-WQFN 裸露焊盤 供應商設備封裝:20-TQFN-EP(5x5) 包裝:托盤
ADA4941-1YCPZ-RL 功能描述:IC DIFF ADC DRIVER 18BIT 8-LFCSP RoHS:是 類別:集成電路 (IC) >> 線性 - 放大器 - 專用 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:60 系列:- 類型:可變增益放大器 應用:CATV 安裝類型:表面貼裝 封裝/外殼:20-WQFN 裸露焊盤 供應商設備封裝:20-TQFN-EP(5x5) 包裝:托盤
ADA4941-1YR-EBZ 功能描述:BOARD EVAL FOR ADA4941-1YR RoHS:是 類別:編程器,開發系統 >> 評估板 - 運算放大器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:-