- 您現在的位置：買賣IC網 > PDF目錄5435 > ADA4310-1ARHZ-R7 (Analog Devices Inc)IC OPAMP CF DUAL LDIST 10MSOP PDF資料下載
參數資料
| 型號： | ADA4310-1ARHZ-R7 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 4/16頁 |
| 文件大小： | 0K |
| 描述： | IC OPAMP CF DUAL LDIST 10MSOP |
| 標準包裝： | 1,000 |
| 放大器類型： | 電流反饋 |
| 電路數： | 2 |
| 轉換速率： | 820 V/µs |
| -3db帶寬： | 190MHz |
| 電流 - 輸入偏壓： | 6µA |
| 電壓 - 輸入偏移： | 1000µV |
| 電流 - 電源： | 7.6mA |
| 電壓 - 電源，單路/雙路(±)： | 5 V ~ 12 V，±2.5 V ~ 6 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 10-TFSOP，10-MSOP（0.118"，3.00mm 寬） |
| 供應商設備封裝： | 10-MSOP |
| 包裝： | 帶卷 (TR) |
ADA4310-1
Rev. 0 | Page 12 of 16
BOARD LAYOUT
As is the case with all high speed applications, careful attention
to printed circuit board layout details prevents associated board
parasitics from becoming problematic. Proper RF design
technique is mandatory. The PCB should have a ground plane
covering all unused portions of the component side of the
board to provide a low impedance return path. Removing the
ground plane on all layers from the area near the input and
output pins reduces stray capacitance, particularly in the area of
the inverting inputs. Signal lines connecting the feedback and
gain resistors should be as short as possible to minimize the
inductance and stray capacitance associated with these traces.
Termination resistors and loads should be located as close as
possible to their respective inputs and outputs. Input and output
traces should be kept as far apart as possible to minimize
coupling (crosstalk) though the board. Wherever there are
complementary signals, a symmetrical layout should be
provided to the extent possible to maximize balanced
performance. When running differential signals over a long
distance, the traces on the PCB should be close. This reduces
the radiated energy and makes the circuit less susceptible to RF
interference. Adherence to stripline design techniques for long
signal traces (greater than about 1 inch) is recommended.
For more information on high speed board layout, go to
www.analog.com and A Practical Guide to High-Speed Printed-
Circuit-Board Layout.
POWER SUPPLY BYPASSING
The ADA4310-1 operates on supplies, from +5 V to ±6 V. The
ADA4310-1 circuit should be powered with a well-regulated
power supply. Careful attention must be paid to decoupling the
power supply. High quality capacitors with low equivalent series
resistance (ESR), such as multilayer ceramic capacitors
(MLCCs), should be used to minimize supply voltage ripple and
power dissipation. In addition, 0.1 μF MLCC decoupling
capacitors should be located no more than -inch away from
each of the power supply pins. A large, usually tantalum, 10 μF
capacitor is required to provide good decoupling for lower
frequency signals and to supply current for fast, large signal
changes at the ADA4310-1 outputs. Bypassing capacitors should
be laid out in such a manner to keep return currents away from
the inputs of the amplifiers. This minimizes any voltage drops
that can develop due to ground currents flowing through the
ground plane. A large ground plane also provides a low
impedance path for the return currents.
相關PDF資料 |
PDF描述 |
|---|---|
| TSW-129-06-S-S | CONN HEADER 29POS .100" SGL GOLD |
| LT1784CS5#TRPBF | IC OPAMP R-R IN/OUT TSOT-23-5 |
| LT1784CS5#TR | IC OPAMP R-R IN/OUT TSOT-23-5 |
| LTC6240IS8#TRPBF | IC OP AMP SINGLE R-R 8-SOIC |
| P6SMB36CAT3 | TVS ZENER BIDIRECT 600W 36V SMB |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADA43101ARHZRL | 制造商:ANALOG 功能描述:REEL |
| ADA4310-1ARHZ-RL | 功能描述:IC OPAMP CF DUAL LDIST 10MSOP RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:160 系列:- 放大器類型:通用 電路數:4 輸出類型:滿擺幅 轉換速率:10 V/µs 增益帶寬積:9MHz -3db帶寬:- 電流 - 輸入偏壓:1pA 電壓 - 輸入偏移:250µV 電流 - 電源:730µA 電流 - 輸出 / 通道:28mA 電壓 - 電源，單路/雙路(±):2.7 V ~ 5.5 V，±1.35 V ~ 2.75 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:16-SOIC N 包裝:管件 |
| ADA4311-1 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Low Cost, Dual, High Current Output Line Driver with Shutdown |
| ADA4311-1ARHZ | 功能描述:IC LINE DRVR DUAL HI CURR 10MSOP RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:1 系列:- 放大器類型:通用 電路數:4 輸出類型:滿擺幅 轉換速率:0.028 V/µs 增益帶寬積:105kHz -3db帶寬:- 電流 - 輸入偏壓:3nA 電壓 - 輸入偏移:100µV 電流 - 電源:3.3µA 電流 - 輸出 / 通道:12mA 電壓 - 電源，單路/雙路(±):2.7 V ~ 12 V，±1.35 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:14-TSSOP 包裝:剪切帶 (CT) 其它名稱:OP481GRUZ-REELCT |
| ADA4311-1ARHZ1 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Low Cost, Dual, High Current Output Line Driver with Shutdown |
發布緊急采購，3分鐘左右您將得到回復。