- 您現在的位置：買賣IC網 > PDF目錄373972 > AD9985BSTZ-110 (ANALOG DEVICES INC) 110 MSPS/140 MSPS Analog Interface for Flat Panel Displays PDF資料下載
參數資料
| 型號： | AD9985BSTZ-110 |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 其它接口 |
| 英文描述： | 110 MSPS/140 MSPS Analog Interface for Flat Panel Displays |
| 中文描述： | SPECIALTY INTERFACE CIRCUIT, PQFP80 |
| 封裝： | LEAD FREE, MS-026BEC, LQFP-80 |
| 文件頁數： | 10/32頁 |
| 文件大?。?/td> | 349K |
| 代理商： | AD9985BSTZ-110 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
AD9985
Pin
Name
SOGIN
Rev. 0 | Page 10 of 32
Function
Sync-on-Green Input
This input is provided to assist with processing signals with embedded sync, typically on the Green channel. The pin is
connected to a high speed comparator with an internally generated threshold. The threshold level can be programmed in
10 mV steps to any voltage between 10 mV and 330 mV above the negative peak of the input signal. The default voltage
threshold is 150 mV. When connected to an ac-coupled graphics signal with embedded sync, it will produce a noninverting
digital output on SOGOUT. (This is usually a composite sync signal, containing both vertical and horizontal sync information
that must be separated before passing the horizontal sync signal to Hsync.) When not used, this input should be left
unconnected. For more details on this function and how it should be configured, refer to the Sync-on-Green section.
External Clamp Input
This logic input may be used to define the time during which the input signal is clamped to ground. It should be exercised
when the reference dc level is known to be present on the analog input channels, typically during the back porch of the
graphics signal. The CLAMP pin is enabled by setting control bit Clamp Function to 1 (Register 0FH, Bit 7, default is 0). When
disabled, this pin is ignored and the clamp timing is determined internally by counting a delay and duration from the trailing
edge of the Hsync input. The logic sense of this pin is controlled by Clamp Polarity Register 0FH, Bit 6. When not used, this pin
must be grounded and Clamp Function programmed to 0.
Clock Generator Coast Input (Optional)
This input may be used to cause the pixel clock generator to stop synchronizing with Hsync and continue producing a clock at
its current frequency and phase. This is useful when processing signals from sources that fail to produce horizontal sync pulses
during the vertical interval. The COAST signal is generally
not
required for PC-generated signals. The logic sense of this pin is
controlled by Coast Polarity (Register 0FH, Bit 3). When not used, this pin may be grounded and Coast Polarity programmed to
1, or tied HIGH (to V
D
through a 10 k resistor) and Coast Polarity programmed to 0. Coast Polarity defaults to 1 at power-up.
CLAMP
COAST
REF
BYPASS
Internal Reference BYPASS
Bypass for the internal 1.25 V band gap reference. It should be connected to ground through a 0.1 μF capacitor. The absolute
accuracy of this reference is ±4%, and the temperature coefficient is ±50 ppm, which is adequate for most AD9985 applica-
tions. If higher accuracy is required, an external reference may be employed instead.
Midscale Voltage Reference BYPASS
Bypass for the internal midscale voltage reference. It should be connected to ground through a 0.1 μF capacitor. The exact
voltage varies with the gain setting of the Blue channel.
External Filter Connection
For proper operation, the pixel clock generator PLL requires an external filter. Connect the filter shown in Figure 8 to this pin.
For optimal performance, minimize noise and parasitics on this node.
POWER SUPPLY
V
D
Main Power Supply
These pins supply power to the main elements of the circuit. They should be filtered and as quiet as possible.
V
DD
Digital Output Power Supply
A large number of output pins (up to 25) switching at high speed (up to 110 MHz) generates a lot of power supply transients
(noise). These supply pins are identified separately from the V
D
pins so special care can be taken to minimize output noise
transferred into the sensitive analog circuitry. If the AD9985 is interfacing with lower voltage logic, V
DD
may be connected to a
lower supply voltage (as low as 2.5 V) for compatibility.
PV
D
Clock Generator Power Supply
The most sensitive portion of the AD9985 is the clock generation circuitry. These pins provide power to the clock PLL and help
the user design for optimal performance. The designer should provide quiet, noise-free power to these pins.
GND
Ground
The ground return for all circuitry on-chip. It is recommended that the AD9985 be assembled on a single solid ground plane,
with careful attention given to ground current paths.
MIDSCV
FILT
相關PDF資料 |
PDF描述 |
|---|---|
| AD9985 | 110 MSPS/140 MSPS Analog Interface for Flat Panel Displays |
| AD9985KSTZ-110 | 110 MSPS/140 MSPS Analog Interface for Flat Panel Displays |
| AD9985KSTZ-140 | 110 MSPS/140 MSPS Analog Interface for Flat Panel Displays |
| AD9990 | Dual Channel, 14-Bit CCD Signal Processor with V-Driver and Precision Timing |
| AD9991KCPRL | 10-Bit CCD Signal Processor with Precision Timing Generator |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9985KST-110 | 制造商:Analog Devices 功能描述:110 MSPS/140 MSPS ANLG INTRFC FOR FLAT PNL DISPLAYS 80LQFP - Bulk |
| AD9985KSTZ-110 | 功能描述:IC INTERFACE 8BIT 110MSPS 80LQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 專用 系列:- 特色產品:NXP - I2C Interface 標準包裝:1 系列:- 應用:2 通道 I²C 多路復用器 接口:I²C，SM 總線 電源電壓:2.3 V ~ 5.5 V 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:剪切帶 (CT) 安裝類型:表面貼裝 產品目錄頁面:825 (CN2011-ZH PDF) 其它名稱:568-1854-1 |
| AD9985KSTZ-140 | 功能描述:IC INTERFACE 8BIT 140MSPS 80LQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 專用 系列:- 標準包裝:3,000 系列:- 應用:PDA，便攜式音頻/視頻，智能電話 接口:I²C，2 線串口 電源電壓:1.65 V ~ 3.6 V 封裝/外殼:24-WQFN 裸露焊盤 供應商設備封裝:24-QFN 裸露焊盤（4x4） 包裝:帶卷 (TR) 安裝類型:表面貼裝 產品目錄頁面:1015 (CN2011-ZH PDF) 其它名稱:296-25223-2 |
| AD9990 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Dual Channel, 14-Bit CCD Signal Processor with V-Driver and Precision Timing |
| AD9990BBCZ | 功能描述:IC CCD SGNL PROCESSOR 112CSPBGA RoHS:是 類別:集成電路 (IC) >> 接口 - 傳感器和探測器接口 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:74 系列:- 類型:觸控式傳感器 輸入類型:數字 輸出類型:數字 接口:JTAG，串行 電流 - 電源:100µA 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。