參數資料
型號： AD9983AKSTZ-140
廠商： ANALOG DEVICES INC
元件分類： 其它接口
英文描述： High Performance 8-Bit Display Interface
中文描述： SPECIALTY INTERFACE CIRCUIT, PQFP80
封裝： ROHS COMPLIANT, PLASTIC, MS-026BEC, LQFP-80
文件頁數： 35/44頁
文件大?。?/td> 470K
代理商： AD9983AKSTZ-140
Preliminary Technical Data
AD9983A
INPUT AND POWER CONTROL
0x1E—Bit[7] Channel Select Override
This bit provides an override to the automatic input channel
selection. Power-up default setting is 0.
Rev. PrA | Page 35 of 44
Table 43. Channel Source Override
Override
0
1
Result
Channel input source determined by chip
Channel input source determined by user
Register 0x1E, Bit 6
0x1E—Bit[6] Channel Select
This bit selects the active input channel if Register 0x1E, Bit 7 = 1.
This selects between Channel 0 data and syncs or Channel 1
data and syncs. Power-up default setting is 0.
Table 44. Channel Select
Channel Select
0
1
0x1E—Bit[5] Programmable Bandwidth
This bit selects between a low or high input bandwidth. It is
useful in limiting noise for lower frequency inputs. The power-
up default setting is 1. Low analog input bandwidth is ~100 MHz;
high analog input bandwidth is ~200 MHz.
Result
Channel 0 data and syncs are selected
Channel 1 data and syncs are selected
Table 45. Input Bandwidth Select.
Input Bandwidth
0
1
0x1E—Bit[4] Power-Down Control Select
Result
Low analog input bandwidth
High analog input bandwidth
This bit determines whether power-down is controlled
manually or automatically by the chip. If automatic control is
selected (Register 0x1E, Bit 4), the AD9983A decision is based
on the status of the sync detect bits (Register 0x24, Bit 2, Bit 3,
Bit 6, and Bit 7). If either an Hsync or a sync-on-green input is
detected on any input, the chip powers up or powers down. For
manual control, the AD9983A allows the flexibility of control
through both a dedicated pin and a register bit. The dedicated
pin allows a hardware watchdog circuit to control power-down,
while the register bit allows power-down to be controlled by
software. With manual power-down control, the polarity of the
power-down pin must be set (Register 0x1E, Bit 2) whether it is
used or not. If unused, it is recommended to set the polarity to
active high and hardwire the pin to ground with a 10 kΩ resistor
.
Table 46. Auto Power-Down Select.
Power-Down Select
0
Result
Manual power-down control
(user determines power-down)
Auto power-down control
(chip determines power-down)
1
0x1E—Bit[3] Power-Down
This bit is used to manually place the chip in power-down
mode. It is only used if manual power-down control is selected
(see Bit 4 above). Both the state of this register bit and the
power-down pin (Pin 17) are used to control manual power-
down. (See the Power Management section for more details on
power-down.)
Table 47. Power-Down Settings
Power-Down Select
0
1
0x1E—Bit[2] Power-Down Pin Polarity
Pin 17
0
X
Result
Normal operation
Power-down
This bit defines the polarity of the power-down pin (Pin 17). It
is only used if manual power-down control is selected (see
0x1E—Bit[4] Power-Down Control Select)
.
Table 48. Power-Down Pin Polarity
Select
0
1
0x1E—Bit[1] Power-Down Fast Switching Control
Result
Power-down pin is active low
Power-down pin is active high
This bit controls a special fast switching mode. With this bit the
AD9983A can stay active during power-down and only put the
outputs in high impedance. This option is useful when the data
outputs from two chips are connected on a PCB and the user
wants to switch instantaneously between the two
.
Table 49. Power-Down Fast Switching Control
Fast Switching Control
0
1
Result
Normal power-down operation
The chip stays powered up and the
outputs are put in high impedance
mode
0x1E—Bit[0] SOGOUT High Impedance Control
This bit controls whether the SOGOUT pin is in high
impedance or not, when in power-down mode. In most cases,
SOGOUT is not put in high impedance during normal oper-
ation. It is usually needed for sync detection by the graphics
controller. The option to put SOGOUT in high impedance is
included mainly to allow for factory testing modes.
Table 50. SOGOUT High Impedance Control
SOGOUT Control
0
Result
SOGOUT operates as normal during
power-down
SOGOUT is in high impedance
during power-down
1
相關PDF資料
PDF描述
AD9983AKSTZ-1401 High Performance 8-Bit Display Interface
AD9983AKSTZ-170 High Performance 8-Bit Display Interface
AD9983AKSTZ-1701 High Performance 8-Bit Display Interface
AD9983A High Performance 8-Bit Display Interface
AD9983AKCPZ-140 High Performance 8-Bit Display Interface
相關代理商/技術參數
參數描述
AD9983AKSTZ-1401 制造商:AD 制造商全稱:Analog Devices 功能描述:High Performance 8-Bit Display Interface
AD9983AKSTZ-170 功能描述:IC DISPLAY 8BIT 170MSPS 80LQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 專用 系列:- 特色產品:NXP - I2C Interface 標準包裝:1 系列:- 應用:2 通道 I²C 多路復用器 接口:I²C，SM 總線 電源電壓:2.3 V ~ 5.5 V 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:剪切帶 (CT) 安裝類型:表面貼裝 產品目錄頁面:825 (CN2011-ZH PDF) 其它名稱:568-1854-1
AD9983AKSTZ-1701 制造商:AD 制造商全稱:Analog Devices 功能描述:High Performance 8-Bit Display Interface
AD9983KSTZ-110 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述:
AD9983KSTZ-140 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*