- 您現在的位置：買賣IC網 > PDF目錄373972 > AD9981KSTZ-80 (ANALOG DEVICES INC) High Performance 10-Bit Display Interface PDF資料下載
參數資料
| 型號： | AD9981KSTZ-80 |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 其它接口 |
| 英文描述： | High Performance 10-Bit Display Interface |
| 中文描述： | SPECIALTY INTERFACE CIRCUIT |
| 文件頁數： | 40/44頁 |
| 文件大?。?/td> | 506K |
| 代理商： | AD9981KSTZ-80 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁當前第40頁第41頁第42頁第43頁第44頁
AD9981
Preliminary Technical Data
TWO-WIRE SERIAL CONTROL PORT
A two-wire serial interface control interface is provided. Up to
two AD9981 devices may be connected to the two-wire serial
interface, with each device having a unique address.
Rev. 0 | Page 40 of 44
The two-wire serial interface comprises a clock (SCL) and a bi-
directional data (SDA) pin. The analog flat panel interface acts
as a slave for receiving and transmitting data over the serial
interface. When the serial interface is not active, the logic levels
on SCL and SDA are pulled high by external pull-up resistors.
Data received or transmitted on the SDA line must be stable for
the duration of the positive-going SCL pulse. Data on SDA must
change only when SCL is low. If SDA changes state while SCL is
high, the serial interface interprets that action as a start or stop
sequence.
The following are the five components to serial bus operation:
Start signal
Slave address byte
Base register address byte
Data byte to read or write
Stop signal
When the serial interface is inactive (SCL and SDA are high),
communications are initiated by sending a start signal. The start
signal is a high-to-low transition on SDA while SCL is high.
This signal alerts all slaved devices that a data transfer sequence
is coming.
The first eight bits of data transferred after a start signal
comprise a 7-bit slave address (the first seven bits) and a single
R/W\ bit (the eighth bit). The R/W\ bit indicates the direction
of data transfer, read from 1 or write to 0 on the slave device. If
the transmitted slave address matches the address of the device
(set by the state of the Serial A0 address [SA0] input pin in
Table 70), the AD9981 acknowledges the match by bringing
SDA low on the 9th SCL pulse. If the addresses do not match,
the AD9981 does not acknowledge it.
Table 70. Serial Port Addresses
Bit 7
Bit 6
A6 (MSB)
A5
1
0
1
0
DATA TRANSFER VIA SERIAL INTERFACE
For each byte of data read or written, the MSB is the first bit in
the sequence.
Bit 5
A4
0
0
Bit 4
A3
1
1
Bit 3
A2
1
1
Bit 2
A1
0
0
Bit 1
A0
0
1
If the AD9981 does not acknowledge the master device during a
write sequence, the SDA remains high so the master can gener-
ate a stop signal. If the master device does not acknowledge the
AD9981 during a read sequence, the AD9981 interprets this as
end-of-data. The SDA remains high so the master can generate
a stop signal.
Writing data to specific control registers of the AD9981 requires
that the 8-bit address of the control register of interest be writ-
ten after the slave address has been established. This control
register address is the base address for subsequent write opera-
tions. The base address auto-increments by one for each byte of
data written after the data byte intended for the base address. If
more bytes are transferred than there are available addresses,
the address will not increment and remain at its maximum
value of 0x2E. Any base address higher than 0x2E will not pro-
duce an acknowledge signal. Data are read from the control
registers of the AD9981 in a similar manner. Reading requires
two data transfer operations:
The base address must be written with the R/W bit of the slave
address byte low to set up a sequential read operation. Reading
(the R/W\ bit of the slave address byte high) begins at the
previously established base address. The address of the read
register auto-increments after each byte is transferred.
To terminate a read/write sequence to the AD9981, a stop signal
must be sent. A stop signal comprises a low-to-high transition
of SDA while SCL is high.
A repeated start signal occurs when the master device driving
the serial interface generates a start signal without first genera-
ting a stop signal to terminate the current communication. This
is used to change the mode of communication (read, write)
between the slave and master without releasing the serial
interface lines.
SDA
SCL
t
BUFF
t
STAH
t
DHO
t
DSU
t
DAL
t
DAH
t
STASU
t
STOSU
0
Figure 17. Serial Port Read/Write Timing
相關PDF資料 |
PDF描述 |
|---|---|
| AD9981KSTZ-95 | High Performance 10-Bit Display Interface |
| AD9983AKSTZ-140 | High Performance 8-Bit Display Interface |
| AD9983AKSTZ-1401 | High Performance 8-Bit Display Interface |
| AD9983AKSTZ-170 | High Performance 8-Bit Display Interface |
| AD9983AKSTZ-1701 | High Performance 8-Bit Display Interface |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9981KSTZ-95 | 功能描述:IC INTERFACE 10BIT ANALOG 80LQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 專用 系列:- 特色產品:NXP - I2C Interface 標準包裝:1 系列:- 應用:2 通道 I²C 多路復用器 接口:I²C，SM 總線 電源電壓:2.3 V ~ 5.5 V 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:剪切帶 (CT) 安裝類型:表面貼裝 產品目錄頁面:825 (CN2011-ZH PDF) 其它名稱:568-1854-1 |
| AD9981XSTZ-110 | 制造商:Analog Devices 功能描述:HIGH PERFORMANCE 10-BIT DISPLAY INTERFACE - Bulk |
| AD9983A | 制造商:AD 制造商全稱:Analog Devices 功能描述:High Performance 8-Bit Display Interface |
| AD9983A/PCB | 制造商:AD 制造商全稱:Analog Devices 功能描述:High Performance 8-Bit Display Interface |
| AD9983A/PCBZ | 功能描述:KIT EVALUATION AD9983A RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:Advantiv® 標準包裝:1 系列:PCI Express® (PCIe) 主要目的:接口，收發器，PCI Express 嵌入式:- 已用 IC / 零件:DS80PCI800 主要屬性:- 次要屬性:- 已供物品:板 |
發布緊急采購，3分鐘左右您將得到回復。