- 您現在的位置：買賣IC網 > PDF目錄16463 > AD9854/PCBZ (Analog Devices Inc)BOARD EVAL FOR AD9854 PDF資料下載
參數資料
| 型號： | AD9854/PCBZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 32/52頁 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL FOR AD9854 |
| 產品培訓模塊： | Direct Digital Synthesis Tutorial Series (1 of 7): Introduction Direct Digital Synthesizer Tutorial Series (7 of 7): DDS in Action Direct Digital Synthesis Tutorial Series (3 of 7): Angle to Amplitude Converter Direct Digital Synthesis Tutorial Series (6 of 7): SINC Envelope Correction Direct Digital Synthesis Tutorial Series (4 of 7): Digital-to-Analog Converter Direct Digital Synthesis Tutorial Series (2 of 7): The Accumulator |
| 設計資源： | AD9854 Eval Brd Schematic AD9854 Eval Brd BOM |
| 標準包裝： | 1 |
| 系列： | AgileRF™ |
| 主要目的： | 計時，直接數字合成（DDS） |
| 已用 IC / 零件： | AD9854 |
| 已供物品： | 板 |
| 相關產品： | AD9854ASTZ-ND - IC DDS QUADRATURE CMOS 80-LQFP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁當前第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁
AD9854
Rev. E | Page 38 of 52
MSB/LSB TRANSFERS
The AD9854 serial port can support MSB- and LSB-first data
formats. This functionality is controlled by Bit 1 of Serial
Register Bank 20 hex. When this bit is set active high, the
AD9854 serial port is in LSB-first format. This bit defaults low,
to the MSB-first format. The instruction byte must be written in
the format indicated by Bit 1 of Serial Register Bank 20 hex.
Therefore, if the AD9854 is in LSB-first mode, the instruction
byte must be written from least significant bit to most
significant bit.
CONTROL REGISTER DESCRIPTION
The control register is located in the shaded portion of Table 8
at Address 1D to Address 20 hex. It is composed of 32 bits.
Bit 31 is located at the top left position, and Bit 0 is located in
the lower right position of the shaded portion. In the text that
follows, the register descriptions have been subdivided to make it
easier to locate the text associated with specific control categories.
CR [31:29] are open.
CR [28] is the comparator power-down bit. When this bit is set
(Logic 1), its signal indicates to the comparator that a power-
down mode is active. This bit is an output of the digital section
and is an input to the analog section.
CR [27] must always be written to Logic 0. Writing this bit to
Logic 1 causes the AD9854 to stop functioning until a master
reset is applied.
CR [26] is the Q DAC power-down bit. When this bit is set
(Logic 1), it indicates to the Q DAC that a power-down mode
is active.
CR [25] is the full DAC power-down bit. When this bit is set
(Logic 1), it indicates to both the I and Q DACs, as well as the
reference, that a power-down mode is active.
CR [24] is the digital power-down bit. When this bit is set
(Logic 1), its signal indicates to the digital section that a power-
down mode is active. Within the digital section, the clocks are
forced to dc, effectively powering down the digital section. In
this state, the PLL still accepts the REFCLK signal and
continues to output the higher frequency.
CR [23] is reserved. Write to 0.
CR [22] is the PLL range bit, which controls the VCO gain. The
power-up state of the PLL range bit is Logic 1; a higher gain is
required for frequencies greater than 200 MHz.
CR [21] is the bypass PLL bit, active high. When this bit is
active, the PLL is powered down and the REFCLK input is used
to drive the system clock signal. The power-up state of the
bypass PLL bit is Logic 1 with PLL bypassed.
CR [20:16] bits are the PLL multiplier factor. These bits are the
REFCLK multiplication factor unless the bypass PLL bit is set.
The PLL multiplier valid range is from 4 to 20, inclusive.
CR [15] is the Clear Accumulator 1 bit. This bit has a one-shot
type of function. When this bit is written active (Logic 1), a
Clear Accumulator 1 signal is sent to the DDS logic, resetting
the accumulator value to 0. The bit is then automatically reset,
but the buffer memory is not reset. This bit allows the user to
easily create a sawtooth frequency sweep pattern with minimal
intervention. This bit is intended for chirp mode only, but its
function is still retained in other modes.
CR [14] is the clear accumulator bit. When this bit is active high,
it holds both the Accumulator 1 and Accumulator 2 values at 0
for as long as the bit is active. This allows the DDS phase to be
initialized via the I/O port.
CR [13] is the triangle bit. When this bit is set, the AD9854
automatically performs a continuous frequency sweep from F1
to F2 frequencies and back. This results in a triangular
frequency sweep. When this bit is set, the operating mode must
be set to ramped FSK.
CR [12] is the source Q DAC bit. When this bit is set high, the
Q path DAC accepts data from the Q DAC register.
CR [11:9] are the three bits that describe the five operating
modes of the AD9854:
0x0 = single-tone mode
0x1 = FSK mode
0x2 = ramped FSK mode
0x3 = chirp mode
0x4 = BPSK mode
相關PDF資料 |
PDF描述 |
|---|---|
| LK2125R22K-T | INDUCTOR MULTILAYER .22UH 0805 |
| 6588719-2 | C/A MTRJ-LC DUP OFNR XG |
| M3UUK-2006R | IDC CABLE - MKS20K/MC20M/MKS20K |
| EEM30DTMI-S189 | CONN EDGECARD 60POS R/A .156 SLD |
| 6278033-3 | C/A MT-RJ/MT-RJ SM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9856 | 制造商:AD 制造商全稱:Analog Devices 功能描述:CMOS 200 MHz Quadrature Digital Upconverter |
| AD9856/PCB | 制造商:Analog Devices 功能描述:Evaluation Board For Digital Up Converter 56 Pin LFCSP Ep 制造商:Analog Devices 功能描述:DGTL UP CNVRTR 56LFCSP - Bulk |
| AD9856AST | 制造商:Analog Devices 功能描述:Digital Up Converter 48-Pin LQFP Tray 制造商:Analog Devices 功能描述:IC MODULATOR DIGITAL |
| AD9856ASTZ | 功能描述:IC UPCONVERTER DGTL QUAD 48TQFP RoHS:是 類別:RF/IF 和 RFID >> RF 其它 IC 和模塊 系列:AD9856 標準包裝:100 系列:* |
| AD9857 | 制造商:AD 制造商全稱:Analog Devices 功能描述:CMOS 200 MSPS 14-Bit Quadrature Digital Upconverter |
發布緊急采購，3分鐘左右您將得到回復。