- 您現在的位置：買賣IC網 > PDF目錄1988 > AD9639BCPZ-170 (Analog Devices Inc)IC ADC 12B 170MSPS QUAD 72LFCSP PDF資料下載
參數資料
| 型號： | AD9639BCPZ-170 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 21/36頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 12B 170MSPS QUAD 72LFCSP |
| 標準包裝： | 1 |
| 位數： | 12 |
| 采樣率（每秒）： | 210M |
| 數據接口： | 串行，SPI? |
| 轉換器數目： | 4 |
| 功率耗散（最大）： | 1.39W |
| 電壓電源： | 模擬和數字 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 72-VFQFN 裸露焊盤，CSP |
| 供應商設備封裝： | 72-LFCSP |
| 包裝： | 托盤 |
| 輸入數目和類型： | 8 個單端，單極；4 個差分，單極 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁當前第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
AD9639
Data Sheet
Rev. B | Page 28 of 36
TEMPOUT Pin
The TEMPOUT pin can be used as a coarse temperature sensor
to monitor the internal die temperature of the device. This pin
typically has a 737 mV output with a clock rate of 210 MSPS
and a negative going temperature coefficient of 1.12 mV/°C.
The voltage response of this pin is characterized in Figure 61.
0.85
0.83
0.81
0.79
0.77
0.75
0.73
0.71
0.69
0.67
0.65
–40 –30 –20 –10
0
10
20
30
40
50
60
70
80
TEMPERATURE (°C)
TE
M
P
OU
T
P
IN
V
O
L
T
A
G
E
(
V
)
07
97
3-
0
55
Figure 61. TEMPOUT Pin Voltage vs. Temperature
RBIAS Pin
To set the internal core bias current of the ADC, place a resistor
(nominally equal to 10.0 kΩ) between ground and the RBIAS pin.
The resistor current is derived on chip and sets the AVDD current
of the ADC to a nominal 610 mA at 210 MSPS. Therefore, it is
imperative that a 1% or less tolerance on this resistor be used to
achieve consistent performance.
VCM x Pins
The common-mode output pins can be enabled through the SPI
to provide an external reference bias voltage of 1.4 V for driving
the VIN + x/VIN x analog inputs. The VCM x pins may be
required when connecting external devices, such as an amplifier
or transformer, to interface to the analog inputs.
RESET Pin
The RESET pin resets the datapath and sets all SPI registers to
their default values. To use this pin, the user must resynchronize
the digital outputs. This pin is only 1.8 V tolerant.
PDWN Pin
When asserted high, the PDWN pin turns off all ADC channels,
including the output drivers. This function can be changed to
a standby function (see Address 0x08 in Table 15). This feature
allows the user to place all channels into standby mode. The
output drivers transmit pseudorandom data until the outputs
are disabled using the output mode register (Address 0x14).
When the PDWN pin is asserted high, the AD9639 is placed into
power-down mode, shutting down the reference, reference buffer,
PLL, and biasing networks. In this state, the ADC typically
dissipates 3 mW. If any of the SPI features are changed before
the power-down feature is enabled, the chip continues to function
after PDWN is pulled low without requiring a reset. The AD9639
returns to normal operating mode when the PDWN pin is pulled
low. This pin is only 1.8 V tolerant.
SDO Pin
The SDO pin is for use in applications that require a 4-wire SPI
mode operation. For normal operation, it should be tied low to
AGND through a 10 kΩ resistor. Alternatively, the device pin
can be left open, and the 345 Ω internal pull-down resistor pulls
this pin low. This pin is only 1.8 V tolerant.
SDI/SDIO Pin
The SDI/SDIO pin is for use in applications that require either a
4- or 3-wire SPI mode operation. For normal operation, it should
be tied low to AGND through a 10 kΩ resistor. Alternatively,
the device pin can be left open, and the 30 kΩ internal pull-
down resistor pulls this pin low. This pin is only 1.8 V tolerant.
SCLK Pin
For normal operation, the SCLK pin should be tied to AGND
through a 10 kΩ resistor. Alternatively, the device pin can be left
open, and the 30 kΩ internal pull-down resistor pulls this pin
low. This pin is only 1.8 V tolerant.
CSB Pin
For normal operation, the CSB pin should be tied high to AVDD
through a 10 kΩ resistor. Alternatively, the device pin can be left
open, and the 26 kΩ internal pull-up resistor pulls this pin high.
Tying the CSB pin to AVDD causes all information on the SCLK
and SDI/SDIO pins to be ignored. Tying the CSB pin low causes
all information on the SDO and SDI/SDIO pins to be written to
the device. This feature allows the user to reduce the number of
traces to the device if necessary. This pin is only 1.8 V tolerant.
PGMx Pins
All PGMx pins are automatically initialized as synchronization
pins by default. These pins are used to lock the FPGA timing and
data capture during initial startup. These pins are respective to
each channel (PGM3 = Channel A, PGM2 = Channel B, and so
on). The sync (PGMx) pin should be pulled high until this pin
receives a low signal input from the receiver, during which time
the ADC outputs K28.5 comma symbols to indicate the frame
boundary. When the receiver finds the frame boundary, the
sync identification is deasserted low and the ADC outputs the
valid data on the next packet boundary.
When steady state operation for the device is achieved, these pins
can be assigned as a standby option using the PGM mode register
(Address 0x53 in Table 15). All other PGMx pins become global
synchronization pins. This pin is only 1.8 V tolerant.
相關PDF資料 |
PDF描述 |
|---|---|
| AD9640ABCPZ-125 | IC ADC 14BIT 125MSPS 64LFCSP |
| AD9641BCPZ-80 | IC ADC 14BIT SRL 80MSPS 32LFCSP |
| AD9644BCPZ-80 | IC ADC 14BIT 80MSPS 3V 48LFCSP |
| AD9648BCPZRL7-125 | IC ADC 14BIT 125MSPS 64LFCSP |
| AD9649BCPZRL7-80 | IC ADC 14BIT 80MSPS 32LFCSP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9639BCPZ-210 | 功能描述:IC ADC 12B 170MSPS QUAD 72LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
| AD9639BCPZRL-170 | 功能描述:IC ADC 12B 170MSPS QUAD 72LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:250 系列:- 位數:12 采樣率（每秒）:1.8M 數據接口:并聯 轉換器數目:1 功率耗散（最大）:1.82W 電壓電源:模擬和數字 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-LQFP 供應商設備封裝:48-LQFP（7x7） 包裝:管件 輸入數目和類型:2 個單端，單極 |
| AD9639BCPZRL-210 | 功能描述:模數轉換器 - ADC Quad 12 Bit 210 MSPS Seria 1.8V ADC RoHS:否 制造商:Analog Devices 通道數量: 結構: 轉換速率: 分辨率: 輸入類型: 信噪比: 接口類型: 工作電源電壓: 最大工作溫度: 安裝風格: 封裝 / 箱體: |
| AD9640 | 制造商:AD 制造商全稱:Analog Devices 功能描述:14-Bit, 80/105/125/150 MSPS, 1.8 V Dual Analog-to-Digital Converter |
| AD9640/PCB | 制造商:AD 制造商全稱:Analog Devices 功能描述:14-Bit, 80/105/125/150 MSPS, 1.8 V Dual Analog-to-Digital Converter |
發布緊急采購，3分鐘左右您將得到回復。