- 您現在的位置：買賣IC網 > PDF目錄1988 > AD9627ABCPZ-125 (Analog Devices Inc)IC ADC 12BIT 1255MSPS 64LFCSP PDF資料下載
參數資料
| 型號： | AD9627ABCPZ-125 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 38/76頁 |
| 文件大小： | 0K |
| 描述： | IC ADC 12BIT 1255MSPS 64LFCSP |
| 標準包裝： | 1 |
| 位數： | 12 |
| 采樣率（每秒）： | 125M |
| 數據接口： | 串行，SPI? |
| 轉換器數目： | 2 |
| 功率耗散（最大）： | 800mW |
| 電壓電源： | 模擬和數字 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 64-VFQFN 裸露焊盤，CSP |
| 供應商設備封裝： | 64-LFCSP-VQ（9x9） |
| 包裝： | 托盤 |
| 輸入數目和類型： | 4 個單端，單極；2 個差分，單極 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁當前第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁
AD9627
Rev. B | Page 43 of 76
MEMORY MAP
READING THE MEMORY MAP REGISTER TABLE
Each row in the memory map register table has eight bit locations.
The memory map is roughly divided into four sections: the chip
configuration registers (Address 0x00 to Address 0x02); the
channel index and transfer registers (Address 0x05 and
Address 0xFF); the ADC functions registers, including setup,
control, and test (Address 0x08 to Address 0x25); and the digital
feature control registers (Address 0x100 to Address 0x11B).
The memory map register table (see Table 25) documents the
default hexadecimal value for each hexadecimal address shown.
The column with the heading Bit 7 (MSB) is the start of the
default hexadecimal value given. For example, Address 0x18,
the VREF select register, has a hexadecimal default value of 0xC0.
This means that Bit 7 = 1, Bit 6 = 1, and the remaining bits are 0s.
This setting is the default reference selection setting. The default
value uses a 2.0 V p-p reference. For more information on this
function and others, see Application Note AN-877, Interfacing to
High Speed ADCs via SPI. This document details the functions
controlled by Register 0x00 to Register 0xFF. The remaining
registers, from Register 0x100 to Register 0x11B, are documented
in the Memory Map Register Description section.
Open Locations
All address and bit locations that are not included in Table 25
are not currently supported for this device. Unused bits of a
valid address location should be written with 0s. Writing to these
locations is required only when part of an address location is
open (for example, Address 0x18). If the entire address location
is open (for example, Address 0x13), this address location should
not be written.
Default Values
After the AD9627 is reset, critical registers are loaded with
default values. The default values for the registers are given in
the memory map register table, Table 25.
Logic Levels
An explanation of logic level terminology follows:
“Bit is set” is synonymous with “bit is set to Logic 1” or
“writing Logic 1 for the bit.”
“Clear a bit” is synonymous with “bit is set to Logic 0” or
“writing Logic 0 for the bit.”
Transfer Register Map
Address 0x08 to Address 0x18 are shadowed. Writes to these
addresses do not affect part operation until a transfer command
is issued by writing 0x01 to Address 0xFF, setting the transfer bit.
This allows these registers to be updated internally and simulta-
neously when the transfer bit is set. The internal update takes
place when the transfer bit is set, and the bit autoclears.
Channel-Specific Registers
Some channel setup functions, such as the signal monitor
thresholds, can be programmed differently for each channel.
In these cases, channel address locations are internally duplicated
for each channel. These registers and bits are designated in Table 25
as local. These local registers and bits can be accessed by setting
the appropriate Channel A or Channel B bits in Register 0x05.
If both bits are set, the subsequent write affects the registers of
both channels. In a read cycle, only Channel A or Channel B
should be set to read one of the two registers. If both bits are set
during an SPI read cycle, the part returns the value for Channel A.
Registers and bits designated as global in Table 25 affect the
entire part or the channel features where independent settings are
not allowed between channels. The settings in Register 0x05 do
not affect the global registers and bits.
相關PDF資料 |
PDF描述 |
|---|---|
| AD9627ABCPZ11-150 | IC ADC 11BIT 150MSPS 64LFCSP |
| AD9628BCPZRL7-125 | IC ADC 12BIT 125MSPS 64LFCSP |
| AD9629BCPZ-65 | IC ADC 12BIT 65MSPS 32LFCSP |
| AD9633BCPZRL7-105 | IC ADC 12BIT SRL 105MSPS 48LFCSP |
| AD9634BCPZRL7-170 | IC ADC 12BIT SRL 170MSPS 32LFCSP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9627ABCPZ-150 | 功能描述:IC ADC 12BIT 150MSPS 64LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 其它有關文件:TSA1204 View All Specifications 標準包裝:1 系列:- 位數:12 采樣率（每秒）:20M 數據接口:并聯 轉換器數目:2 功率耗散（最大）:155mW 電壓電源:模擬和數字 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-TQFP 供應商設備封裝:48-TQFP（7x7） 包裝:Digi-Reel® 輸入數目和類型:4 個單端，單極；2 個差分，單極 產品目錄頁面:1156 (CN2011-ZH PDF) 其它名稱:497-5435-6 |
| AD9627ABCPZ-80 | 功能描述:IC ADC 12BIT 80MSPS 64LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| AD9627BCPZ-105 | 制造商:Analog Devices 功能描述:ADC Dual Pipelined 105Msps 12-bit Parallel/LVDS 64-Pin LFCSP EP |
| AD9627BCPZ11-105 | 制造商:Analog Devices 功能描述: 制造商:Rochester Electronics LLC 功能描述: |
| AD9627BCPZ11-150 | 制造商:Analog Devices 功能描述: 制造商:Rochester Electronics LLC 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。