參數資料
型號： AD9516-4/PCBZ
廠商： Analog Devices Inc
文件頁數： 33/80頁
文件大?。?/td> 0K
描述： BOARD EVAL FOR AD9516-4 1.8GHZ
產品培訓模塊： Active Filter Design Tools
設計資源： AD9516 Eval Brd Schematic
AD9516 Gerber Files
AD9516-4 BOM
標準包裝： 1
主要目的： 計時，時鐘發生器
嵌入式： 否
已用 IC / 零件： AD9516-4
主要屬性： 2 輸入，14 輸出，1.6GHz VCO
次要屬性： CMOS、LVDS、LVPECL 輸出邏輯，ADIsimCLK&trade 圖形用戶界面
已供物品： 板，線纜，CD，電源
產品目錄頁面： 776 (CN2011-ZH PDF)
相關產品： AD9516-4BCPZ-REEL7-ND - IC CLOCK GEN 1.8GHZ VCO 64-LFCSP
AD9516-4BCPZ-ND - IC CLOCK GEN 1.6GHZ VCO 64-LFCSP
Data Sheet
AD9516-4
Rev. C | Page 39 of 80
PROGRAMMABLE
N DELAY
REFIN (REF1)
REFIN (REF2)
CLK
REF1
REF2
STATUS
R
DIVIDER
VCO STATUS
PROGRAMMABLE
R DELAY
REFERENCE
SWITCHOVER
REF_SEL
CPRSET VCP
VS
GND
RSET
DISTRIBUTION
REFERENCE
REFMON
CP
STATUS
LD
P, P + 1
PRESCALER
A/B
COUNTERS
N DIVIDER
BYPASS
LF
LOW DROPOUT
REGULATOR (LDO)
VCO
PHASE
FREQUENCY
DETECTOR
LOCK
DETECT
CHARGE
PUMP
PL
L
RE
F
E
RE
NCE
HOLD
0
1
0
1
DIVIDE BY
2, 3, 4, 5, OR 6
06
42
3-
0
70
Figure 54. Reference and VCO Status Monitors
VCO Calibration
The AD9516 on-chip VCO must be calibrated to ensure proper
operation over process and temperature. The VCO calibration
is controlled by a calibration controller running off of a divided
REFIN clock. The calibration requires that the PLL be set up
properly to lock the PLL loop and that the REFIN clock be present.
During the first initialization after a power-up or a reset of the
AD9516, a VCO calibration sequence is initiated by setting
Register 0x018[0] = 1b. This can be done as part of the initial
setup, before executing update registers (Register 0x232[0] = 1b).
Subsequent to the initial setup, a VCO calibration sequence is
initiated by resetting Register 0x018[0] = 0b, executing an update
registers operation, setting Register 0x018[0] = 1b, and executing
another update registers operation. A readback bit, Bit 6 in
Register 0x01F, indicates when a VCO calibration is finished
by returning a logic true (that is, 1b).
The sequence of operations for the VCO calibration is as follows:
Program the PLL registers to the proper values for the PLL
loop. Note that that automatic holdover mode must be
disabled, and the VCO divider must not be set to “Static.”
Ensure that the input reference signal is present.
For the initial setting of the registers after a power-up or reset,
initiate VCO calibration by setting Register 0x018[0] = 1b.
Subsequently, whenever a calibration is desired, set
Register 0x018[0] = 0b, update registers; and then set
Register 0x018[0] = 1b, update registers.
A SYNC operation is initiated internally, causing the
outputs to go to a static state determined by normal SYNC
function operation.
VCO calibrates to the desired setting for the requested
VCO frequency.
Internally, the SYNC signal is released, allowing outputs to
continue clocking.
PLL loop is closed.
PLL locks.
A sync is executed during the VCO calibration; therefore, the
outputs of the AD9516 are held static during the calibration,
which prevents unwanted frequencies from being produced.
However, at the end of a VCO calibration, the outputs may
resume clocking before the PLL loop is completely settled.
The VCO calibration clock divider is set as shown in Table 54
(Register 0x018[2:1]).
The calibration divider divides the PFD frequency (reference
frequency divided by R) down to the calibration clock. The
calibration occurs at the PFD frequency divided by the
calibration divider setting. Lower VCO calibration clock
frequencies result in longer times for a calibration to be
completed.
The VCO calibration clock frequency is given by
fCAL_CLOCK = fREFIN/(R × cal_div)
where:
fREFIN is the frequency of the REFIN signal.
R is the value of the R divider.
cal_div is the division set for the VCO calibration divider
(Register 0x018[2:1]).
The VCO calibration takes 4400 calibration clock cycles.
Therefore, the VCO calibration time in PLL reference clock
cycles is given by
Time to Calibrate VCO =
4400 × R × cal_div PLL Reference Clock Cycles
Table 29. Example Time to Complete a VCO Calibration
with Different fREFIN Frequencies
fREFIN (MHz)
R Divider
PFD
Time to Calibrate VCO
100
1
100 MHz
88 μs
10
1 MHz
8.8 ms
10
100
100 kHz
88 ms
相關PDF資料
PDF描述
EVAL-ADAU1761Z BOARD EVAL FOR ADAU1761
MAX6174BASA+ IC VREF SERIES PREC 4.096V 8SOIC
GSC06DRXI-S734 CONN EDGECARD 12POS DIP .100 SLD
0982660987 CBL 29PS 0.5MM JMPR TYPE A 1.18"
SRR5028-680Y INDUCTOR POWER 68UH 0.62A SMD
相關代理商/技術參數
參數描述
AD9516-5 制造商:AD 制造商全稱:Analog Devices 功能描述:14-Output Clock Generator
AD9516-5/PCBZ 功能描述:BOARD EVAL FOR AD9516-5 2.5GHZ RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 標準包裝:1 系列:- 主要目的:電信，線路接口單元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要屬性:T1/J1/E1 LIU 次要屬性:- 已供物品:板，電源，線纜，CD 其它名稱:82EBV2081
AD9516-5BCPZ 功能描述:IC CLOCK GEN W/PLL 64-LFCSP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘發生器，PLL，頻率合成器 系列:- 標準包裝:2,000 系列:- 類型:PLL 時鐘發生器 PLL:帶旁路 輸入:LVCMOS，LVPECL 輸出:LVCMOS 電路數:1 比率 - 輸入:輸出:2:11 差分 - 輸入:輸出:是/無 頻率 - 最大:240MHz 除法器/乘法器:是/無 電源電壓:3.135 V ~ 3.465 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:32-LQFP 供應商設備封裝:32-TQFP（7x7） 包裝:帶卷 (TR)
AD9516-5BCPZ-REEL7 功能描述:IC CLOCK GEN W/PLL 64-LFCSP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘發生器，PLL，頻率合成器 系列:- 標準包裝:2,000 系列:- 類型:PLL 時鐘發生器 PLL:帶旁路 輸入:LVCMOS，LVPECL 輸出:LVCMOS 電路數:1 比率 - 輸入:輸出:2:11 差分 - 輸入:輸出:是/無 頻率 - 最大:240MHz 除法器/乘法器:是/無 電源電壓:3.135 V ~ 3.465 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:32-LQFP 供應商設備封裝:32-TQFP（7x7） 包裝:帶卷 (TR)
AD9516-5PCBZ 制造商:AD 制造商全稱:Analog Devices 功能描述:14-Output Clock Generator
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*