- 您現在的位置：買賣IC網 > PDF目錄17027 > AD9233-125EBZ (Analog Devices Inc)BOARD EVALUATION FOR AD9233 PDF資料下載
參數資料
| 型號： | AD9233-125EBZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 22/44頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD EVALUATION FOR AD9233 |
| 標準包裝： | 1 |
| ADC 的數量： | 1 |
| 位數： | 12 |
| 采樣率（每秒）： | 125M |
| 數據接口： | 串行 |
| 輸入范圍： | 1 ~ 2 Vpp |
| 在以下條件下的電源（標準）： | 455mW @125MSPS |
| 工作溫度： | -40°C ~ 85°C |
| 已用 IC / 零件： | AD9233 |
| 已供物品： | 板，電源 |
| 相關產品： | AD9233BCPZRL7-125-ND - IC ADC 12BIT 125MSPS 48-LFCSP AD9233BCPZRL7-105-ND - IC ADC 12BIT 105MSPS 48-LFCSP AD9233BCPZ-105-ND - IC ADC 12BIT 105MSPS 48-LFCSP AD9233BCPZ-125-ND - IC ADC 12BIT 80/105/125 48-LFCSP AD9233BCPZ-80-ND - IC ADC 12BIT 80MSPS 48-LFCSP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁當前第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁
AD9233
Rev. A | Page 29 of 44
DEFAULT OPERATION AND JUMPER SELECTION
SETTINGS
The following is a list of the default and optional settings or
modes allowed on the AD9233 Rev. A evaluation board.
POWER
Connect the switching power supply that is supplied in the
evaluation kit between a rated 100 V ac to 240 V ac wall outlet
at 47 Hz to 63 Hz and P500.
VIN
The evaluation board is set up for a double balun configuration
analog input with optimum 50 Ω impedance matching out to
70 MHz. For more bandwidth response, the differential capacitor
across the analog inputs can be changed or removed (see Table 8).
The common mode of the analog inputs is developed from the
center tap of the transformer via the CML pin of the ADC. See
the Analog Input Considerations section for more information.
VREF
VREF is set to 1.0 V by tying the SENSE pin to ground via
JP507 (Pin 1 and Pin 2). This causes the ADC to operate in
2.0 V p-p full-scale range. A separate external reference option
is also included on the evaluation board. Simply connect JP507
between Pin 2 and Pin 3, connect JP501, and provide an external
reference at E500. Proper use of the VREF options is detailed in
the Voltage Reference section.
RBIAS
RBIAS requires a 10 kΩ (R503) to ground and is used to set the
ADC core bias current.
CLOCK
The default clock input circuitry is derived from a simple
transformer-coupled circuit using a high bandwidth 1:1
impedance ratio transformer (T503) that adds a very low
amount of jitter to the clock path. The clock input is 50 Ω
terminated and ac-coupled to handle single-ended sine wave
inputs. The transformer converts the single-ended input to a
differential signal that is clipped before entering the ADC
clock inputs.
PDWN
To enable the power-down feature, connect JP506, shorting the
PDWN pin to AVDD.
CSB
The CSB pin is internally pulled-up, setting the chip into
external pin mode, to ignore the SDIO and SCLK information.
To connect the control of the CSB pin to the SPI circuitry on the
evaluation board, connect JP1 Pin 1 and Pin 2. To set the chip
into serial pin mode and to enable the SPI information on the
SDIO and SCLK pins, tie JP1 low (connect Pin 2 and Pin 3) in
the always enabled mode.
SCLK/DFS
If the SPI port is in external pin mode, the SCLK/DFS pin sets the
data format of the outputs. If the pin is left floating, the pin is
internally pulled down, setting the default condition to binary.
Connecting JP2 Pin 2 and Pin 3 sets the format to twos
complement. If the SPI port is in serial pin mode, connecting
JP2 Pin 1 and Pin 2 connects the SCLK pin to the on board
SPI circuitry. See the Serial Port Interface (SPI) section for
more details.
SDIO/DCS
If the SPI port is in external pin mode, the SDIO/DCS pin acts
to set the duty cycle stabilizer. If the pin is left floating, the pin is
internally pulled up, setting the default condition to DCS enabled.
To disable the DCS, connect JP3 Pin 2 and Pin 3. If the SPI port
is in serial pin mode, connecting JP3 Pin 1 and Pin 2 connects the
SDIO pin to the on-board SPI circuitry. See the Serial Port
Interface (SPI) section for more details.
ALTERNATIVE CLOCK CONFIGURATIONS
A differential LVPECL clock can also be used to clock the ADC
input using the AD9515 (U500). When using this drive option,
the components listed in Table 16 need to be populated.
Consult the AD9515 data sheet for further information.
To configure the analog input to drive the AD9515 instead of
the default transformer option, the following components need
to be added, removed, and/or changed.
Remove R507, R508, C532, and C533 in the default
clock path.
Populate R505 with a 0 Ω resistor and C531 in the default
clock path.
Populate R511, R512, R513, R515 to R524, U500, R580,
R582, R583, R584, C536, C537, and R586.
If using an oscillator, two oscillator footprint options are also
available (OSC500) to check the performance of the ADC.
JP508 provides the user flexibility in using the enable pin, which
is common on most oscillators. Populate OSC500, R575, R587,
and R588 to use this option.
相關PDF資料 |
PDF描述 |
|---|---|
| LGU2D681MELB | CAP ALUM 680UF 200V 20% SNAP |
| GCM22DRUN | CONN EDGECARD 44POS DIP .156 SLD |
| AD9204-20EBZ | BOARD EVALUATION 20MSPS AD9204 |
| GCM22DRUH | CONN EDGECARD 44POS DIP .156 SLD |
| AD9204-40EBZ | BOARD EVALUATION 40MSPS AD9204 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9233-80EB | 制造商:Analog Devices 功能描述: |
| AD9233-80EBZ | 功能描述:BOARD EVAL FOR AD9233 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
| AD9233BCPZ-105 | 功能描述:IC ADC 12BIT 105MSPS 48-LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 其它有關文件:TSA1204 View All Specifications 標準包裝:1 系列:- 位數:12 采樣率（每秒）:20M 數據接口:并聯 轉換器數目:2 功率耗散（最大）:155mW 電壓電源:模擬和數字 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-TQFP 供應商設備封裝:48-TQFP（7x7） 包裝:Digi-Reel® 輸入數目和類型:4 個單端，單極；2 個差分，單極 產品目錄頁面:1156 (CN2011-ZH PDF) 其它名稱:497-5435-6 |
| AD9233BCPZ-125 | 功能描述:IC ADC 12BIT 80/105/125 48-LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
| AD9233BCPZ-80 | 功能描述:IC ADC 12BIT 80MSPS 48-LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 其它有關文件:TSA1204 View All Specifications 標準包裝:1 系列:- 位數:12 采樣率（每秒）:20M 數據接口:并聯 轉換器數目:2 功率耗散（最大）:155mW 電壓電源:模擬和數字 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-TQFP 供應商設備封裝:48-TQFP（7x7） 包裝:Digi-Reel® 輸入數目和類型:4 個單端，單極；2 個差分，單極 產品目錄頁面:1156 (CN2011-ZH PDF) 其它名稱:497-5435-6 |
發布緊急采購，3分鐘左右您將得到回復。