參數資料
型號: AD9216-40PCB
廠商: Analog Devices, Inc.
英文描述: 10-Bit, 65/80/105 MSPS Dual A/D Converter
中文描述: 10位,65/80/105 MSPS雙通道的A / D轉換器
文件頁數: 16/20頁
文件大小: 298K
代理商: AD9216-40PCB
AD9216
Preliminary Technical Data
The data format can be selected for either offset binary or twos
complement. This is discussed later in the Data Format section.
Rev. PrD
Page 16 of 20
6/15/2004
TIMING
The AD9216 provides latched data outputs with a pipeline
delay of six clock cycles. Data outputs are available one
propagation delay (t
) after the rising edge of the clock signal.
Refer to Figure 2 for a detailed timing diagram.
The internal duty cycle stabilizer can be enabled on the
AD9216 using the DCS pin. This provides a stable 50% duty
cycle to internal circuits.
The length of the output data lines and loads placed on them
should be minimized to reduce transients within the AD9216.
These transients can detract from the converter’s dynamic
performance. The lowest typical conversion rate of the AD9216
is 1 MSPS. At clock rates below 1 MSPS, dynamic
performance may degrade.
Figure 6.
NEEDS UPDATING
Example of Multiplexed Data Format Using the Channel A Output and the Same Clock Tied to CLK_A, CLK_B, and
MUX_SELECT
DATA FORMAT
The AD9216 data output format can be configured for either
twos complement or offset binary. This is controlled by the
Data Format Select pin (DFS). Connecting DFS to AGND will
produce offset binary output data. Conversely, connecting DFS
to AVDD will format the output data as twos complement.
The output data from the dual A/D converters can be
multiplexed onto a single 10-Bits output bus. The multiplexing
is accomplished by toggling the MUX_SELECT bit, which
directs channel data to the same or opposite channel data port.
When MUX_SELECT is logic high, the Channel A data is
directed to Channel A output bus, and Channel B data is
directed to the Channel B output bus. When MUX_SELECT is
logic low, the channel data is reversed, i.e., Channel A data is
directed to the Channel B output bus and Channel B data is
directed to the Channel A output bus. By toggling the
MUX_SELECT bit, multiplexed data is available on either of
the output data ports.
If the ADCs are run with synchronized timing, this same clock
can be applied to the MUX_SELECT bit. After the
MUX_SELECT rising edge, either data port will have the data
for its respective channel; after the falling edge, the alternate
channel’s data will be placed on the bus. Typically, the other
unused bus would be disabled by setting the appropriate OEB
high to reduce power consumption and noise. Figure 6 shows
an example of multiplex mode. When multiplexing data, the
data rate is two times the sample rate. Note that both channels
must remain active in this mode and that each channel's power-
down pin must remain low.
相關PDF資料
PDF描述
AD9216-65 10-Bit, 65/80/105 MSPS Dual A/D Converter
AD9216-65PCB 10-Bit, 65/80/105 MSPS Dual A/D Converter
AD9216-80 10-Bit, 65/80/105 MSPS Dual A/D Converter
AD9216BCP-65 10-Bit, 65/80/105 MSPS Dual A/D Converter
AD9216BCPZ-105 10-Bit, 65/80/105 MSPS Dual A/D Converter
相關代理商/技術參數
參數描述
AD9216-65 制造商:AD 制造商全稱:Analog Devices 功能描述:10-Bit, 65/80/105 MSPS Dual A/D Converter
AD9216-65PCB 制造商:AD 制造商全稱:Analog Devices 功能描述:10-Bit, 65/80/105 MSPS Dual A/D Converter
AD9216-80 制造商:AD 制造商全稱:Analog Devices 功能描述:10-Bit, 65/80/105 MSPS Dual A/D Converter
AD9216-80PCB 制造商:Analog Devices 功能描述:Evaluation Board With AD9216BCPZ-80 Dual A/D Converter 制造商:Analog Devices 功能描述:EVAL BD W/ AD9216BCPZ-80 DUAL A/D CNVRTR - Trays
AD9216-80PCBZ 功能描述:BOARD EVAL FOR AD9216 80MSPS RoHS:是 類別:編程器,開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率(每秒):94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源(標準):- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板,軟件