- 您現在的位置：買賣IC網 > PDF目錄10616 > AD8325ARUZ (Analog Devices Inc)IC LN DVR CATV FINE-STEP 28TSSOP PDF資料下載
參數資料
| 型號： | AD8325ARUZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 2/16頁 |
| 文件大小： | 0K |
| 描述： | IC LN DVR CATV FINE-STEP 28TSSOP |
| 標準包裝： | 50 |
| 類型： | 線路驅動器，發射器 |
| 應用： | 調制解調器，機頂盒 |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 28-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 28-TSSOP |
| 包裝： | 管件 |
AD8325
Differential Inputs
The AD8325-EVAL evaluation board may be driven with a
differential signal in one of two ways. A transformer may be
used to convert a single-ended signal to differential, or a differ
ential signal source may be used. Figure 7 and the following
paragraphs describe each of these methods.
Single-Ended-to-Differential Input (Figure 7, Option 1)
A TOKO 617DB-A0070 1:1 transformer is preinstalled in the
T3 location of the evaluation board. Install 0
W chip resistors at
R14, R15, and R20, and leave R16 through R19 open. For
50
W differential input impedance, install a 51.1 W resistor at R13.
For 75
W differential input impedance, use a 78.7 W resistor.
In this configuration, the input signal must be applied to the
VIN+ port of the evaluation board. For input impedances other
than 50
W or 75 W, the correct value for R13 can be calculated
using the following equation.
Desired Input Impedance = (R13 1600)
Differential Input (Figure 7, Option 2)
If a differential signal source is available, it may be applied
directly to both the VIN+ and VIN– input ports of the evaluation
board. In this case, 0
W chip resistors should be installed at
locations R16 through R19, and R14, R15, and R20 should be
left open. The equation at the end of the preceding paragraph
can be used to compute the correct value for R13 for any
desired differential input impedance. For differential input
impedances of 75
W or 150 W, the value of R13 will be 78.7 W or
165
W respectively.
DIFF IN
T1
R13
AD8325
DIFFERENTIAL INPUT, OPTION 1
VIN+
–
DIFFERENTIAL INPUT, OPTION 2
VIN
AD8325
R13
Figure 7. Differential Input Termination Options
Installing the Visual Basic Control Software
To install the “CABDRIVE_25” evaluation board control soft
ware, close all Windows applications and then run “SETUP.EXE”
located on Disk 1 of the AD8325 Evaluation Software. Follow
the on-screen instructions and insert Disk 2 when prompted to
do so. Enter the path of the directory into which the software
will be installed and select the button in the upper left corner to
complete the installation.
Running the Software
To invoke the control software, go to START -> PROGRAMS
-> CABDRIVE_25, or select the AD8325.EXE icon from the
directory containing the software.
Controlling the Gain/Attenuation of the AD8325
The slide bar controls the AD8325’s gain/attenuation, which is
displayed in dB and in V/V. The gain scales at 0.7526 dB per
LSB with the valid codes being from decimal 0 to 79. The gain
code (i.e., position of the slide bar) is displayed in decimal, binary,
and hexadecimal (see Figure 8).
Transmit Enable, Transmit Disable, and Sleep
The “Transmit Enable” and “Transmit Disable” buttons select
the mode of operation of the AD8325 by controlling the logic
level on the asynchronous TXEN pin. The “Transmit Enable”
button applies a Logic 1 to the TXEN pin putting the AD8325
in forward transmit mode. The “Transmit Disable” button
applies a Logic 0 to the TXEN pin selecting reverse mode, where
the forward signal transmission is disabled while a back termina
tion of 75
W is maintained. On early revisions of the software,
the “Transmit Enable” and “Transmit Disable” buttons may be
called “Power-Up” and “Power-Down” respectively. Checking
the “Enable SLEEP Mode” box applies a Logic 0 to the asyn
chronous
SLEEP pin, putting the AD8325 into SLEEP mode.
Memory Section
The “MEMORY” section of the software provides a convenient
way to alternate between two gain settings. The “X->M1” but
ton stores the current value of the gain slide bar into memory
while the “RM1” button recalls the stored value, returning the
gain slide bar to that level. The “X->M2” and “RM2” buttons
work in the same manner.
–10–
REV. A
相關PDF資料 |
PDF描述 |
|---|---|
| MAX3430EPA+ | IC TXRX RS-485 3.3V 8-DIP |
| VI-BWM-IV-F3 | CONVERTER MOD DC/DC 10V 150W |
| VI-BW3-IV-F4 | CONVERTER MOD DC/DC 24V 150W |
| VI-BW3-IV-F1 | CONVERTER MOD DC/DC 24V 150W |
| VI-BW2-IV-F3 | CONVERTER MOD DC/DC 15V 150W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD8325ARUZ-REEL | 功能描述:IC LN DVR CATV FINE-STEP 28TSSOP RoHS:是 類別:集成電路 (IC) >> 線性 - 視頻處理 系列:- 產品變化通告:Product Discontinuation 07/Mar/2011 標準包裝:3,000 系列:OMNITUNE™ 類型:調諧器 應用:移動電話，手機，視頻顯示器 安裝類型:表面貼裝 封裝/外殼:65-WFBGA 供應商設備封裝:PG-WFSGA-65 包裝:帶卷 (TR) 其它名稱:SP000365064 |
| AD8325-EVAL | 制造商:Analog Devices 功能描述:Evaluation Board For 5 V CATV Line Driver Fine Step Output Power Control 制造商:Analog Devices 功能描述:EVAL BD 5 V CATV LINE DRVR FINE STEP OUTPUT PWR CONTROL - Bulk 制造商:Analog Devices 功能描述:EVAL CARD ((NS)) |
| AD8326 | 制造商:AD 制造商全稱:Analog Devices 功能描述:High Output Power Programmable CATV Line Driver |
| AD8326ARE | 制造商:Analog Devices 功能描述:SP Amp Line Driver Amp Single 制造商:Rochester Electronics LLC 功能描述:TSSOP HIGH OUTPUT POWER CATV LINE DRIVER - Bulk |
| AD8326ARE-EVAL | 制造商:Analog Devices 功能描述:Evaluation Board For AD8326 High Output Power Programmable CATV Line Driver |
發布緊急采購，3分鐘左右您將得到回復。