參數資料
型號： AD8197ASTZ
廠商： ANALOG DEVICES INC
元件分類： 運動控制電子
英文描述： 4:1 HDMI/DVI Switch with Equalization
中文描述： 4-CHANNEL, AUDIO/VIDEO SWITCH, QCC100
封裝： 14 X 14 MM, LEAD FREE, MS-028BED, LQFP-100
文件頁數： 28/32頁
文件大?。?/td> 486K
代理商： AD8197ASTZ
AD8197
Preliminary Technical Data
These four signals can be switched through the auxiliary bus of
the AD8197 and do not need to be routed with the same strict
considerations as the high speed TMDS signals.
PrA| Page 28 of 32
In general, it is sufficient to route each auxiliary signal as a
single-ended trace. These signals are not sensitive to impedance
discontinuities, do not require a reference plane, and can be
routed on multiple layers of the PCB. However, it is best to
follow strict layout practices whenever possible to prevent the
PCB design from affecting the overall application. The specific
routing of the HPD, CEC, and DDC lines depends upon the
application in which the AD8197 is being used.
For example, the maximum speed of signals present on the
auxiliary lines is 100 kHz I
2
C data on the DDC lines; therefore,
any layout that enables 100 kHz I
2
C to be passed over the DDC
bus should suffice. The HDMI 1.3 specification, however, places
a strict 50 pF limit on the amount of capacitance that can be
measured on either SDA or SCL at the HDMI input connector.
This 50 pF limit includes the HDMI connector, the PCB, and
whatever capacitance is seen at the input of the AD8197, or an
equivalent receiver. There is a similar limit of 100 pF of input
capacitance for the CEC line.
The parasitic capacitance of traces on a PCB increases with
trace length. To help ensure that a design satisfies the HDMI
specification, the length of the CEC and DDC lines on the PCB
should be made as short as possible. Additionally, if there is a
reference plane in the layer adjacent to the auxiliary traces in
the PCB stack-up, relieving or clearing out this reference plane
immediately under the auxiliary traces significantly decreases
the amount of parasitic trace capacitance. An example of the
board stackup is shown in Figure 33.
PCB DIELECTRIC
LAYER 1: SIGNAL (MICROSTRIP)
SILKSCREEN
SILKSCREEN
PCB DIELECTRIC
PCB DIELECTRIC
LAYER 2: GND (REFERENCE PLANE)
LAYER 3: PWR (REFERENCE PLANE)
LAYER 4: SIGNAL (MICROSTRIP)
W
3W
3W
REFERENCE LAYER
RELIEVED UNDERNEATH
MICROSTRIP
0
Figure 33. Example Board Stackup
HPD is a dc signal presented by a sink to a source to indicate
that the source EDID is available for reading. The placement
of this signal is not critical, but it should be routed as directly
as possible.
When the AD8197 is powered up, one set of the auxiliary in-
puts is passively routed to the outputs. In this state, the AD8197
looks like a 100 Ω resistor between the selected auxiliary inputs
and the corresponding outputs as illustrated in Figure 27. The
AD8197 does not buffer the auxiliary signals, therefore, the
input traces, output traces, and the connection through the
AD8197 all must be considered when designing a PCB to meet
HDMI/DVI specifications. The unselected auxiliary inputs of the
AD8197 are placed into a high impedance mode when the device
is powered up. To ensure that all of the auxiliary inputs of the
AD8197 are in a high impedance mode when the device is powered
off, it is necessary to power the AMUXVCC supply as illustrated
in Figure 28.
In contrast to the auxiliary signals, the AD8197 buffers the
TMDS signals, allowing a PCB designer to layout the TMDS
inputs independently of the outputs.
相關PDF資料
PDF描述
AD8197ASTZ-RL 4:1 HDMI/DVI Switch with Equalization
AD8197-EVAL 4:1 HDMI/DVI Switch with Equalization
AD8197 4:1 HDMI/DVI Switch with Equalization
AD8200YCHIPS High Common-Mode Voltage, Single-Supply Difference Amplifier
AD8200YCSURF High Common-Mode Voltage, Single-Supply Difference Amplifier
相關代理商/技術參數
參數描述
AD8197ASTZ-RL 功能描述:IC SWITCH DVI/HDMI 4:1 100-LQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 模擬開關，多路復用器，多路分解器 系列:- 其它有關文件:STG4159 View All Specifications 標準包裝:5,000 系列:- 功能:開關 電路:1 x SPDT 導通狀態電阻:300 毫歐 電壓電源:雙電源 電壓 - 電源，單路/雙路(±):±1.65 V ~ 4.8 V 電流 - 電源:50nA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:7-WFBGA，F(xiàn)CBGA 供應商設備封裝:7-覆晶 包裝:帶卷 (TR)
AD8197B 制造商:AD 制造商全稱:Analog Devices 功能描述:4:1 HDMI/DVI Switch with Equalization
AD8197BASTZ 功能描述:IC SWITCH DVI/HDMI 4:1 100-LQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 模擬開關，多路復用器，多路分解器 系列:- 應用說明:Ultrasound Imaging Systems Application Note 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:250 系列:- 功能:開關 電路:單刀單擲 導通狀態電阻:48 歐姆 電壓電源:單電源 電壓 - 電源，單路/雙路(±):2.7 V ~ 5.5 V 電流 - 電源:5µA 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:48-LQFP 供應商設備封裝:48-LQFP（7x7） 包裝:托盤
AD8197BASTZ-RL 功能描述:IC SWITCH DVI/HDMI 4:1 100-LQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 模擬開關，多路復用器，多路分解器 系列:- 其它有關文件:STG4159 View All Specifications 標準包裝:5,000 系列:- 功能:開關 電路:1 x SPDT 導通狀態電阻:300 毫歐 電壓電源:雙電源 電壓 - 電源，單路/雙路(±):±1.65 V ~ 4.8 V 電流 - 電源:50nA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:7-WFBGA，F(xiàn)CBGA 供應商設備封裝:7-覆晶 包裝:帶卷 (TR)
AD8197BASTZ-RLKL1 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*