- 您現在的位置：買賣IC網 > PDF目錄375243 > AD8197-EVAL (Analog Devices, Inc.) 4:1 HDMI/DVI Switch with Equalization PDF資料下載
參數資料
| 型號： | AD8197-EVAL |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | 4:1 HDMI/DVI Switch with Equalization |
| 中文描述： | 4:1的HDMI / DVI接口與均衡開關 |
| 文件頁數： | 29/32頁 |
| 文件大?。?/td> | 486K |
| 代理商： | AD8197-EVAL |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁當前第29頁第30頁第31頁第32頁
Preliminary Data Sheet
AD8197
Power Supplies
The AD8197 has five separate power supplies referenced to
two separate grounds. The supply/ground pairs are:
AVCC/AVEE
VTTI/AVEE
VTTO/AVEE
DVCC/DVEE
AMUXVCC/DVEE
PrA | Page 29 of 32
The AVCC/AVEE (3.3 V) and DVCC/DVEE (3.3 V) supplies
power the core of the AD8197. The VTTI/AVEE supply (3.3 V)
powers the input termination (see Figure 25). Similarly, the
VTTO/AVEE supply (3.3 V) powers the output termination
(see Figure 26). The AMUXVCC/DVEE supply (3.3 V to 5 V)
powers the auxiliary multiplexer core and determines the
maximum allowed voltage on the auxiliary lines. For example,
if the DDC bus is using 5 V I
2
C, then AMUXVCC should be
connected to +5 V relative to DVEE.
In a typical application, all pins labeled AVEE or DVEE should
be connected directly to ground. All pins labeled AVCC,
DVCC, VTTI, or VTTO should be connected to 3.3 V, and
Pin AMUXVCC tied to 5 V. The supplies can also be powered
individually, but care must be taken to ensure that each stage of
the AD8197 is powered correctly.
Power Supply Bypassing
The AD8197 requires minimal supply bypassing. When
powering the supplies individually, place a 0.01 μF capacitor
between each 3.3 V supply pin (AVCC, DVCC, VTTI, and
VTTO) and ground to filter out supply noise. Generally, bypass
capacitors should be placed near the power pins and should
connect directly to the relevant supplies (without long inter-
vening traces). For example, to improve the parasitic inductance
of the power supply decoupling capacitors, minimize the trace
length between capacitor landing pads and the vias as shown in
Figure 34.
EXTRA ADDED INDUCTANCE
RECOMMENDED
NOT RECOMMENDED
0
Figure 34. Recommended Pad Outline for Bypass Capacitors
In applications where the AD8197 is powered by a single 3.3 V
supply, it is recommended to use two reference supply planes
and bypass the 3.3 V reference plane to the ground reference
plane with one 220 pF, one 1000 pF, two 0.01 μF, and one 4.7 μF
capacitors. The capacitors should via down directly to the
supply planes and be placed within a few centimeters of the
AD8197. The AMUXVCC supply does not require additional
bypassing. This bypassing scheme is illustrated in Figure 35.
Figure 35. Example Placement of Power Supply Decoupling Capacitors
Around the AD8197
相關PDF資料 |
PDF描述 |
|---|---|
| AD8197 | 4:1 HDMI/DVI Switch with Equalization |
| AD8200YCHIPS | High Common-Mode Voltage, Single-Supply Difference Amplifier |
| AD8200YCSURF | High Common-Mode Voltage, Single-Supply Difference Amplifier |
| AD8206YCSURF | Single-Supply 42 V System Difference Amplifier |
| AD8206YR | Single-Supply 42 V System Difference Amplifier |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD820 | 制造商:Analog Devices 功能描述: |
| AD820_07 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Single-Supply, Rail-to-Rail, Low Power FET-Input Op Amp |
| AD8200 | 制造商:AD 制造商全稱:Analog Devices 功能描述:High Common-Mode Voltage, Single Supply Difference Amplifier |
| AD8200_03 | 制造商:AD 制造商全稱:Analog Devices 功能描述:High Common-Mode Voltage, Single-Supply Difference Amplifier |
| AD8200CHIPS | 制造商:AD 制造商全稱:Analog Devices 功能描述:High Common-Mode Voltage, Single Supply Difference Amplifier |
發布緊急采購，3分鐘左右您將得到回復。