- 您現在的位置：買賣IC網 > PDF目錄5921 > AD8130AR (Analog Devices Inc)IC AMP DIFF LN LDIST 40MA 8SOIC PDF資料下載
參數資料
| 型號： | AD8130AR |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 2/41頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC AMP DIFF LN LDIST 40MA 8SOIC |
| 設計資源： | High CMRR Circuit for Converting Wideband Complementary DAC Outputs to Single-Ended Without Precision Resistors (CN0142) |
| 標準包裝： | 98 |
| 放大器類型： | 差分 |
| 電路數： | 1 |
| 轉換速率： | 1100 V/µs |
| -3db帶寬： | 290MHz |
| 電流 - 輸入偏壓： | 500nA |
| 電壓 - 輸入偏移： | 400µV |
| 電流 - 電源： | 13mA |
| 電流 - 輸出 / 通道： | 40mA |
| 電壓 - 電源，單路/雙路(±)： | 4.5 V ~ 25.2 V，±2.25 V ~ 12.6 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 8-SO |
| 包裝： | 管件 |
第1頁當前第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁
AD8129/AD8130
Rev. C | Page 9 of 40
ABSOLUTE MAXIMUM RATINGS
Table 4.
Parameter
Rating
Supply Voltage
26.4 V
Power Dissipation
Refer to Figure 4
Input Voltage (Any Input)
VS 0.3 V to +VS + 0.3 V
Differential Input Voltage (AD8129)
VS ≥ ±11.5 V
±0.5 V
Differential Input Voltage (AD8129)
VS < ±11.5 V
±6.2 V
Differential Input Voltage (AD8130)
±8.4 V
Storage Temperature Range
65°C to +150°C
Lead Temperature (Soldering, 10 sec)
300°C
Junction Temperature
150°C
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
THERMAL RESISTANCE
θJA is specified for the worst-case conditions, that is, θJA is
specified for the device soldered in a circuit board in still air.
Table 5. Thermal Resistance
Package Type
θJA
Unit
8-Lead SOIC/4-Layer
121
°C/W
8-Lead MSOP/4-Layer
142
°C/W
Maximum Power Dissipation
The maximum safe power dissipation in the AD8129/AD8130
packages is limited by the associated rise in junction temp-
erature (TJ) on the die. At approximately 150°C, which is the
glass transition temperature, the plastic changes its properties.
Even temporarily exceeding this temperature limit can change
the stresses that the package exerts on the die, permanently
shifting the parametric performance of the AD8129/AD8130.
Exceeding a junction temperature of 150°C for an extended
period can result in changes in the silicon devices, potentially
causing failure.
The power dissipated in the package (PD) is the sum of the
quiescent power dissipation and the power dissipated in the
package due to the load drive. The quiescent power is the
voltage between the supply pins (VS) times the quiescent
current (IS). The power dissipated due to the load drive
depends upon the particular application. The power due to
load drive is calculated by multiplying the load current by the
associated voltage drop across the device. RMS voltages and
currents must be used in these calculations.
Airflow reduces θJA. In addition, more metal directly in contact
with the package leads from metal traces through holes, ground,
and power planes reduces the θJA.
Figure 4 shows the maximum safe power dissipation in the
package vs. the ambient temperature for the 8-lead SOIC
(121°C/W) and MSOP (θJA = 142°C/W) packages on a JEDEC
standard 4-layer board. θJA values are approximations.
AMBIENT TEMPERATURE (°C)
M
A
XIM
U
M
POW
E
R
D
ISSIPA
TION
(
W
)
1.75
1.50
1.00
1.25
0.50
0.25
0.75
0
–40 –30 –20 –10 0
10 20 30 40 50 60 70 80 90 100 110 120
SOIC
MSOP
02464-005
Figure 4. Maximum Power Dissipation vs. Temperature
ESD CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on
the human body and test equipment and can discharge without detection. Although this product features
proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy
electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance
degradation or loss of functionality.
相關PDF資料 |
PDF描述 |
|---|---|
| LT1993IUD-4#PBF | IC DIFF AMP/ADC DRVR 16-QFN |
| ADA4817-1ARDZ-R7 | IC OPAMP VF 410MHZ LN 40MA 8SOIC |
| OP284FSZ-REEL7 | IC OPAMP GP R-R 4.25MHZ LN 8SOIC |
| AD8295ACPZ-WP | IC AMP INST 1MHZ TRPL LN 16LFCSP |
| GTCS25-900M-R02 | GAS TUBE 5MM 90V 20% 2.5KA SMD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD8130AR | 制造商:Analog Devices 功能描述:SEMICONDUCTOR ((NW)) |
| AD8130AR-EB | 制造商:Analog Devices 功能描述:LEADED EVALUATION BOARD - Boxed Product (Development Kits) |
| AD8130AR-EBZ | 功能描述:BOARD EVAL FOR AD8130AR RoHS:是 類別:編程器，開發系統 >> 評估板 - 運算放大器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- |
| AD8130ARM | 功能描述:IC AMP DIFF LN LDIST 40MA 8MSOP RoHS:否 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:100 系列:- 放大器類型:通用 電路數:1 輸出類型:- 轉換速率:0.2 V/µs 增益帶寬積:- -3db帶寬:- 電流 - 輸入偏壓:100pA 電壓 - 輸入偏移:30µV 電流 - 電源:380µA 電流 - 輸出 / 通道:- 電壓 - 電源，單路/雙路(±):±2 V ~ 18 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:8-SO 包裝:管件 |
| AD8130ARM-EBZ | 功能描述:BOARD EVAL FOR AD8130ARM RoHS:是 類別:編程器，開發系統 >> 評估板 - 運算放大器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- |
發布緊急采購，3分鐘左右您將得到回復。