- 您現在的位置：買賣IC網 > PDF目錄373935 > AD8099ARDZ-REEL (ANALOG DEVICES INC) Ultralow Distortion, High Speed 0.95 nV/Hz Voltage Noise Op Amp PDF資料下載
參數資料
| 型號： | AD8099ARDZ-REEL |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 運動控制電子 |
| 英文描述： | Ultralow Distortion, High Speed 0.95 nV/Hz Voltage Noise Op Amp |
| 中文描述： | OP-AMP, 500 uV OFFSET-MAX, PDSO8 |
| 封裝： | LEAD FREE, MS-012, SOIC-8 |
| 文件頁數： | 16/28頁 |
| 文件大?。?/td> | 1208K |
| 代理商： | AD8099ARDZ-REEL |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
AD8099
APPLICATIONS
USING THE AD8099
The AD8099 offers unrivaled noise and distortion performance
in low signal gain configurations. In low gain configurations
(less than15), the AD8099 requires external compensation. The
amount of gain and performance needed will determine the
compensation network.
Rev. B | Page 16 of 28
Understanding the subtleties of the AD8099 gives the user
insight on how to exact its peak performance. Use the
component values and circuit configurations shown in the
Applications section as starting points for designs. Specific
circuit applications will dictate the final configuration and value
of your components.
CIRCUIT COMPONENTS
The circuit components are referenced in Figure 59, the
recommended noninverting circuit schematic for the AD8099.
See Table 4 for typical component values and performance data.
1
8
4
7
5
3
6
2
AD8099
C5
0.1
μ
F
C
C
C
F
C1
C4
10
μ
F
C2
10
μ
F
C3
0.1
μ
F
R
C
R
F
R
G
R
S
R1
+V
S
–V
S
V
OUT
DISABLE
0
V
IN
Figure 59. Wideband Noninverting Gain Configuration (SOIC)
R
F
and R
G
—
The feedback resistor and the gain set resistor
determine the noise gain of the amplifier; typical R
F
values
range from 250 to 499 .
C
F
—Creates a zero in the loop response to compensate the pole
created by the input capacitance (including stray capacitance)
and the feedback resistor R
F
. C
F
helps reduce high frequency
peaking and ringing in the closed-loop response. Typical range
is 0.5 pF to 1.5 pF for evaluation circuits used here.
R1
—This resistor terminates the input of the amplifier to the
source resistance of the signal source, typically 50 . (This is
application specific and not always required.)
R
S
—Many high speed amplifiers in low gain configurations
require that the input stage be terminated into a nominal
impedance to maintain stability. The value of R
S
should be kept
to 50 or lower to maintain low noise performance. At higher
gains, R
S
may be reduced or even eliminated. Typical range is
0 to 50 .
C
C
—The compensation capacitor decreases the open-loop gain
at higher frequencies where the phase is degrading. By decreas-
ing the open-loop gain here, the phase margin is increased and
the amplifier is stabilized. Typical range is 0 pF to 5 pF. The
value of C
C
is gain dependent.
R
C
—
The series lead inductance of the package and the com-
pensation capacitance (C
C
) forms a series resonant circuit. R
C
dampens this resonance and prevents oscillations. The
recommended value of R
C
is 50 for a closed-loop gain of 2.
This resistor introduces a zero in the open-loop response and
must be kept low so that this zero occurs at a higher frequency.
The purpose of the compensation network is to decrease the
open-loop gain. If the resistance becomes too large, the gain will
be reduced to the resistor value, and not necessarily to 0 ,
which is what a single capacitor would do over frequency.
Typical value range is 0 to 50 .
C1
—To lower the impedance of R
C
, C1 is placed in parallel with
R
C
. C1 is not required, but greatly reduces peaking at low
closed-loop gains. The typical value range is 0 pF to 2 pF.
C2 and C3
—Bypass capacitors are connected
between
both
supplies for optimum distortion and PSRR performance. These
capacitors should be placed as close as possible to the supply
pins of the amplifier. For
C3, C5
,
a 0508 case size should be
used. The 0508 case size offers reduced inductance and better
frequency response.
C4 and C2
—Electrolytic bypass capacitors.
相關PDF資料 |
PDF描述 |
|---|---|
| AD8099ARD-REEL | Ultralow Distortion, High Speed 0.95 nV/Hz Voltage Noise Op Amp |
| AD8099ARD-REEL7 | Ultralow Distortion, High Speed 0.95 nV/Hz Voltage Noise Op Amp |
| AD8099ARD | Ultralow Distortion, High Speed 0.95 nV/Hz Voltage Noise Op Amp |
| AD8099ARDZ | Ultralow Distortion, High Speed 0.95 nV/Hz Voltage Noise Op Amp |
| AD8099 | Ultralow Distortion, High Speed 0.95 nV/Hz Voltage Noise Op Amp |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD8099ARDZ-REEL7 | 功能描述:IC OPAMP VF ULN ULDIST 8SOIC RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:50 系列:LinCMOS™ 放大器類型:通用 電路數:4 輸出類型:- 轉換速率:0.05 V/µs 增益帶寬積:110kHz -3db帶寬:- 電流 - 輸入偏壓:0.7pA 電壓 - 輸入偏移:210µV 電流 - 電源:57µA 電流 - 輸出 / 通道:30mA 電壓 - 電源，單路/雙路(±):3 V ~ 16 V，±1.5 V ~ 8 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:14-SOIC 包裝:管件 產品目錄頁面:865 (CN2011-ZH PDF) 其它名稱:296-1834296-1834-5 |
| AD8099CP-R2 | 制造商:Analog Devices 功能描述:OP AMP SGL VOLT FDBK 6V/12V 8LFCSP - Tape and Reel |
| AD809BR | 制造商:Rochester Electronics LLC 功能描述:155.52MHZ FREQUENCY SYNTH - Bulk 制造商:Analog Devices 功能描述:Frequency Synthesizer, 16 Pin, Plastic, SOP |
| AD809BR-REEL7 | 功能描述:IC SYNTH FREQ 155.52MHZ 16-SOIC RoHS:否 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘發生器，PLL，頻率合成器 系列:- 標準包裝:1,000 系列:Precision Edge® 類型:時鐘/頻率合成器 PLL:無 輸入:CML，PECL 輸出:CML 電路數:1 比率 - 輸入:輸出:2:1 差分 - 輸入:輸出:是/是 頻率 - 最大:10.7GHz 除法器/乘法器:無/無 電源電壓:2.375 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-VFQFN 裸露焊盤，16-MLF? 供應商設備封裝:16-MLF?（3x3） 包裝:帶卷 (TR) 其它名稱:SY58052UMGTRSY58052UMGTR-ND |
| AD809BRZ | 功能描述:IC SYNTH FREQ 155.52MHZ 16SOIC RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘發生器，PLL，頻率合成器 系列:- 標準包裝:1,000 系列:Precision Edge® 類型:時鐘/頻率合成器 PLL:無 輸入:CML，PECL 輸出:CML 電路數:1 比率 - 輸入:輸出:2:1 差分 - 輸入:輸出:是/是 頻率 - 最大:10.7GHz 除法器/乘法器:無/無 電源電壓:2.375 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-VFQFN 裸露焊盤，16-MLF? 供應商設備封裝:16-MLF?（3x3） 包裝:帶卷 (TR) 其它名稱:SY58052UMGTRSY58052UMGTR-ND |
發布緊急采購，3分鐘左右您將得到回復。