- 您現在的位置：買賣IC網 > PDF目錄373935 > AD8092ARM (ANALOG DEVICES INC) Low-Cost, High-Speed Rail-to-Rail Amplifiers PDF資料下載
參數資料
| 型號： | AD8092ARM |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 運動控制電子 |
| 英文描述： | Low-Cost, High-Speed Rail-to-Rail Amplifiers |
| 中文描述： | DUAL OP-AMP, 27000 uV OFFSET-MAX, PDSO8 |
| 封裝： | MO-187AA, MSOP-8 |
| 文件頁數： | 11/16頁 |
| 文件大小： | 229K |
| 代理商： | AD8092ARM |
–11–
AD8091/AD8092
REV. A
LAYOUT, GROUNDING, AND BYPASSING
CONSIDERATIONS
Power Supply Bypassing
Power supply pins are actually inputs and care must be taken
so that a noise-free stable dc voltage is applied. The purpose of
bypass capacitors is to create low impedances from the supply to
ground at all frequencies, thereby shunting or filtering a majority
of the noise.
Decoupling schemes are designed to minimize the bypassing imped-
ance at all frequencies with a parallel combination of capacitors.
0.01
μ
F or 0.001
μ
F (X7R or NPO) chip capacitors are critical
and should be as close as possible to the amplifier package. Larger
chip capacitors, such as the 0.1
μ
F capacitor, can be shared among
a few closely spaced active components in the same signal path.
A 10
μ
F tantalum capacitor is less critical for high-frequency
bypassing and, in most cases, only one per board is needed at
the supply inputs.
Grounding
A ground plane layer is important in densely packed PC boards to
spread the current minimizing parasitic inductances. However,
an understanding of where the current flows in a circuit is critical
to implementing effective high-speed circuit design. The length
of the current path is directly proportional to the magnitude of
parasitic inductances and thus the high-frequency impedance of
the path. High-speed currents in an inductive ground return will
create an unwanted voltage noise.
The length of the high-frequency bypass capacitor leads are most
critical. A parasitic inductance in the bypass grounding will work
against the low impedance created by the bypass capacitor. Place
the ground leads of the bypass capacitors at the same physical
location. Because load currents flow from the supplies as well,
the ground for the load impedance should be at the same physical
location as the bypass capacitor grounds. For the larger value
capacitors, which are intended to be effective at lower frequencies,
the current return path distance is less critical.
Input Capacitance
Along with bypassing and ground, high-speed amplifiers can be
sensitive to parasitic capacitance between the inputs and ground.
A few pF of capacitance will reduce the input impedance at high
frequencies, in turn increasing the amplifier
’
s gain, causing peaking
of the frequency response or even oscillations, if severe enough.
It is recommended that the external passive components, which
are connected to the input pins, be placed as close as possible to
the inputs to avoid parasitic capacitance. The ground and power
planes must be kept at a distance of at least 0.05 mm from the
input pins on all layers of the board.
Input-to-Output Coupling
The input and output signal traces should not be parallel to mini-
mize capacitive coupling between the inputs and output, avoiding
any positive feedback.
DRIVING CAPACITIVE LOADS
A highly capacitive load will react with the output of the amplifiers,
causing a loss in phase margin and subsequent peaking or even
oscillation, as illustrated in Figures 2 and 3. There are two
methods to effectively minimize its effect.
1. Put a small value resistor in series with the output to isolate
the load capacitor from the amps
’
output stage.
2. Increase the phase margin with higher noise gains or by adding a
pole with a parallel resistor and capacitor from
–
IN to the output.
FREQUENCY
–
MHz
500
0.1
1
10
100
V
= +5V
G = +1
R
L
= 2k
C
L
= 50pF
V
O
= 200mV p-p
8
6
4
2
0
2
4
6
8
10
G
–
Figure 2. Closed-Loop Frequency Response: C
L
= 50 pF
2.60V
2.55V
2.50V
2.45V
2.40V
p
Figure 3. 200 mV Step Response: C
L
= 50 pF
相關PDF資料 |
PDF描述 |
|---|---|
| AD8092ARM-REEL | Low-Cost, High-Speed Rail-to-Rail Amplifiers |
| AD8092ARM-REEL7 | Low-Cost, High-Speed Rail-to-Rail Amplifiers |
| AD8099ACPZ-REEL7 | TV 13C 13#22D SKT RECP |
| AD8099ARDZ-REEL | Ultralow Distortion, High Speed 0.95 nV/Hz Voltage Noise Op Amp |
| AD8099ARD-REEL | Ultralow Distortion, High Speed 0.95 nV/Hz Voltage Noise Op Amp |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD8092ARM-EBZ | 功能描述:BOARD EVAL FOR AD8092ARM RoHS:是 類別:編程器，開發系統 >> 評估板 - 運算放大器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- |
| AD8092ARM-REEL | 制造商:Analog Devices 功能描述:OP Amp Dual GP R-R O/P 制造商:Rochester Electronics LLC 功能描述:SOIC DUAL 200MHZ L/C RAIL-TO-RAIL AMP - Tape and Reel |
| AD8092ARM-REEL7 | 制造商:Analog Devices 功能描述:OP Amp Dual GP R-R O/P 制造商:Analog Devices 功能描述:OP AMP DUAL GP R-R O/P 6V/12V 8MSOP - Tape and Reel |
| AD8092ARMZ | 功能描述:IC OPAMP VF R-R DUAL LDIST 8MSOP RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 產品培訓模塊:Differential Circuit Design Techniques for Communication Applications 標準包裝:1 系列:- 放大器類型:RF/IF 差分 電路數:1 輸出類型:差分 轉換速率:9800 V/µs 增益帶寬積:- -3db帶寬:2.9GHz 電流 - 輸入偏壓:3µA 電壓 - 輸入偏移:- 電流 - 電源:40mA 電流 - 輸出 / 通道:- 電壓 - 電源，單路/雙路(±):3 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-VQFN 裸露焊盤，CSP 供應商設備封裝:16-LFCSP-VQ 包裝:剪切帶 (CT) 產品目錄頁面:551 (CN2011-ZH PDF) 其它名稱:ADL5561ACPZ-R7CT |
| AD8092ARMZ-REEL | 功能描述:IC OPAMP VF R-R DUAL LDIST 8MSOP RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:160 系列:- 放大器類型:通用 電路數:4 輸出類型:滿擺幅 轉換速率:10 V/µs 增益帶寬積:9MHz -3db帶寬:- 電流 - 輸入偏壓:1pA 電壓 - 輸入偏移:250µV 電流 - 電源:730µA 電流 - 輸出 / 通道:28mA 電壓 - 電源，單路/雙路(±):2.7 V ~ 5.5 V，±1.35 V ~ 2.75 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:16-SOIC N 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。