- 您現在的位置：買賣IC網 > PDF目錄373928 > AD8010AN (ANALOG DEVICES INC) 200 mA Output Current High Speed Amplifier PDF資料下載
參數資料
| 型號： | AD8010AN |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 運動控制電子 |
| 英文描述： | 200 mA Output Current High Speed Amplifier |
| 中文描述： | OP-AMP, 15000 uV OFFSET-MAX, 90 MHz BAND WIDTH, PDIP8 |
| 封裝： | MINI, PLASTIC, DIP-8 |
| 文件頁數： | 8/12頁 |
| 文件大?。?/td> | 164K |
| 代理商： | AD8010AN |
AD8010
–8–
REV. A
0
V
INPUT (500mV/DIV)
OUTPUT (1V/DIV)
G = +6
R
F
= 604
V
R
L
= 18.75
V
INPUT
OUTPUT
100ns
Figure 27. Overdrive Recovery; G = +6
OVERDRIVE RECOVERY
Overdrive of an amplifier occurs when the output and/or input
range are exceeded. The amplifier must recover from this over-
drive condition. As shown in Figure 27, the AD8010 recovers
within 35 ns from negative overdrive and within 75 ns from
positive overdrive.
THEORY OF OPERATION
The AD8010 is a current feedback amplifier optimized for high
current output while maintaining excellent performance with
respect to flatness, distortion and differential gain/phase. As a
video distribution amplifier, the AD8010 will drive up to 12
parallel video loads (12.5
) from a single output with 0.04%
differential gain and 0.04
°
differential phase errors. This means
that, unlike designs with one driver per output, any output is a
true reflection of the signal on all other outputs.
The high output current capability of the AD8010 also make it
useful in xDSL applications. The AD8010 can drive a 12.5
single-ended or 25
differential load with low harmonic distor-
tion. This makes it useful in designs that utilize a step-up trans-
former to drive a twisted-pair transmission line.
To achieve these levels of performance special precautions with
respect to supply bypassing are recommended (Figure 29). This
configuration minimizes the contribution from high frequency
supply rejection to differential gain and phase errors as well as
reducing distortion due to harmonic energy in the power
supplies.
R
S
–
V
200
100
10
20
5
C
10
10
15
G = +2
G = +5
G = +1
GAIN AS SHOWN
V
O
= 0.2V p-p
w/
#
30% OVERSHOOT
V
OUT
V
IN
R
F
R
G
150
V
50
V
R
S
C
L
Figure 28. Capacitive Load Drive vs. Series Resistor for
Various Gains
Driving Capacitance Loads
The AD8010 was designed primarily to drive nonreactive loads.
If driving loads with a capacitive component is desired, best
frequency response is obtained by the addition of a small series
resistance as shown in Figure 28. The inset figure shows the
optimum value for R
SERIES
vs. capacitive load. It is worth noting
that the frequency response of the circuit when driving large
capacitive loads will be dominated by the passive roll-off of
R
SERIES
and C
L
.
LAYOUT CONSIDERATIONS
The specified high speed performance of the AD8010 requires
careful attention to board layout and component selection.
Proper R
F
design techniques and low-pass parasitic component
selection are necessary.
The PCB should have a ground plane covering all unused por-
tions of the component side of the board to provide low imped-
ance path. The ground plane should be removed from the area
near the input pins to reduce the parasitic capacitance.
AD8010
V
IN
150
V
R
F
R
G
R
T
+V
S
–V
S
FB
C1
+
R
BT
Z
O
R
L
C2
+
Figure 29. Standard Noninverting Closed-Loop Configura-
tion with Recommended Bypassing Technique
The standard noninverting closed-loop configuration with the
recommended power supply bypassing technique is shown in
Figure 29. Ferrite beads (Amidon Associates, Torrance CA,
Part Number 43101) are used to suppress high frequency power
supply energy on the DUT supply lines at the DUT. C1 and C2
each represent the parallel combination of a 47
μ
F (16 V) tanta-
lum electrolytic capacitor, a 10
μ
F (10 V) tantalum electrolytic
capacitor and a 0.1
μ
F ceramic chip capacitor. Connect C1
from the +V
S
pin to the –V
S
pin. Connect C2 from the –V
S
pin
to signal ground.
The feedback resistor should be located close to the inverting
input pin in order to keep the parasitic capacitance at this node
to a minimum. Parasitic capacitances of less than 1 pF at the
inverting input can significantly affect high speed performance.
Stripline design techniques should be used for long traces
(greater than about 3 cm). These should be designed with a
characteristic impedance (Z
O
) of 50
or 75
and be properly
terminated at each end.
相關PDF資料 |
PDF描述 |
|---|---|
| AD8010AR | 200 mA Output Current High Speed Amplifier |
| AD8010AR-REEL | 200 mA Output Current High Speed Amplifier |
| AD8010AR-REEL7 | 200 mA Output Current High Speed Amplifier |
| AD8010AR-16 | Smartcard Connector; Body Material:Thermoplastic; Contact Material:Tin Bronze; Series:C702A; Operating Temperature Range : C to C RoHS Compliant: Yes |
| AD8010AR-16-REEL | Smartcard Connector; No. of Contacts:6; Body Material:Thermosplastic; Contact Material:Tin Bronze; Contact Plating:Gold Over Nickel; Series:C707A; Operating Temperature Range +/-:-40 C to +85 C; Voltage Rating:540V RoHS Compliant: Yes |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD8010ANZ | 功能描述:IC OPAMP CF 200MA LP 8DIP RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:1 系列:- 放大器類型:通用 電路數:4 輸出類型:滿擺幅 轉換速率:0.028 V/µs 增益帶寬積:105kHz -3db帶寬:- 電流 - 輸入偏壓:3nA 電壓 - 輸入偏移:100µV 電流 - 電源:3.3µA 電流 - 輸出 / 通道:12mA 電壓 - 電源，單路/雙路(±):2.7 V ~ 12 V，±1.35 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:14-TSSOP 包裝:剪切帶 (CT) 其它名稱:OP481GRUZ-REELCT |
| AD8010AR | 功能描述:IC OPAMP CF 200MA LP 8SOIC RoHS:否 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:2,500 系列:Excalibur™ 放大器類型:J-FET 電路數:1 輸出類型:- 轉換速率:45 V/µs 增益帶寬積:10MHz -3db帶寬:- 電流 - 輸入偏壓:20pA 電壓 - 輸入偏移:490µV 電流 - 電源:1.7mA 電流 - 輸出 / 通道:48mA 電壓 - 電源，單路/雙路(±):4.5 V ~ 38 V，±2.25 V ~ 19 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:8-SOIC 包裝:帶卷 (TR) |
| AD8010AR-16 | 制造商:Analog Devices 功能描述:ADSL Driver Single 16-Pin SOIC W Tube 制造商:Rochester Electronics LLC 功能描述:SOIC-WB 160MA OUTPUT CURRENT HI SPD AMP - Bulk |
| AD8010AR-16-REEL | 制造商:Analog Devices 功能描述:ADSL Driver Single 16-Pin SOIC W T/R |
| AD8010AR-16-REEL7 | 制造商:Analog Devices 功能描述:ADSL Driver Single 16-Pin SOIC W T/R 制造商:Rochester Electronics LLC 功能描述:SOIC-WB 160MA OUTPUT CURRENT HI SPD AMP - Tape and Reel |
發布緊急采購，3分鐘左右您將得到回復。