- 您現在的位置：買賣IC網 > PDF目錄10659 > AD7983BRMZ (Analog Devices Inc)IC ADC 16BIT 1.33MSPS 10MSOP PDF資料下載
參數資料
| 型號： | AD7983BRMZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 9/24頁 |
| 文件大小： | 0K |
| 描述： | IC ADC 16BIT 1.33MSPS 10MSOP |
| 標準包裝： | 1 |
| 系列： | PulSAR® |
| 位數： | 16 |
| 采樣率（每秒）： | 1.33M |
| 數據接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 12mW |
| 電壓電源： | 單電源 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 10-TFSOP，10-MSOP（0.118"，3.00mm 寬） |
| 供應商設備封裝： | 10-MSOP |
| 包裝： | 管件 |
| 輸入數目和類型： | 1 個差分，單極 |
| 產品目錄頁面： | 780 (CN2011-ZH PDF) |
AD7983
Rev. A | Page 17 of 24
When CNV goes low, the MSB is output onto SDO. The
remaining data bits are then clocked by subsequent SCK falling
edges. The data is valid on both SCK edges. Although the rising
edge can be used to capture the data, a digital host using the SCK
falling edge allows a faster reading rate provided that it has an
acceptable hold time. After the 16th SCK falling edge or when
CNV goes high, whichever is earlier, SDO returns to high
impedance.
CS MODE, 3-WIRE WITHOUT BUSY INDICATOR
This mode is usually used when a single AD7983 is connected
to an SPI-compatible digital host. The connection diagram is
shown in Figure 26, and the corresponding timing is given in
With SDI tied to VIO, a rising edge on CNV initiates a
conversion, selects the CS mode, and forces SDO to high
impedance. When a conversion is initiated, it continues until
completion irrespective of the state of CNV. This can be useful,
for example, to bring CNV low to select other SPI devices, such
as analog multiplexers; however, CNV must be returned high
before the minimum conversion time elapses and then held
high for the maximum conversion time to avoid the generation
of the busy signal indicator. When the conversion is complete, the
AD7983 enters the acquisition phase and goes into standby mode.
AD7983 SDO
SDI
DATA IN
DIGITAL HOST
CONVERT
CLK
VIO
CNV
SCK
06
97
4-
01
2
Figure 26. CS Mode, 3-Wire Without Busy Indicator
Connection Diagram (SDI High)
SDI = 1
tCNVH
tCONV
tCYC
CNV
ACQUISITION
tACQ
tSCK
tSCKL
CONVERSION
SCK
SDO
D15
D14
D13
D1
D0
tEN
tHSDO
1
2
3
14
15
16
tDSDO
tDIS
tSCKH
06
97
4-
0
13
Figure 27. CS Mode, 3-Wire Without Busy Indicator Serial Interface Timing (SDI High)
相關PDF資料 |
PDF描述 |
|---|---|
| MAX3362EKA#TG16 | IC TXRX RS485/422 SGL SOT23-8 |
| VI-J1L-MW-F3 | CONVERTER MOD DC/DC 28V 100W |
| AD1674ARZ | IC ADC 12BIT 100KSPS 28-SOIC |
| AD7693BRMZ | IC ADC 16BIT 500KSPS 10-MSOP |
| VI-J1L-MW-F2 | CONVERTER MOD DC/DC 28V 100W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7983BRMZRL7 | 制造商:AD 制造商全稱:Analog Devices 功能描述:16-Bit, 1.33 MSPS PulSAR ADC in MSOP/QFN |
| AD7983BRMZ-RL7 | 功能描述:IC ADC 16BIT 1.33MSPS 10MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:PulSAR® 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| AD7984 | 制造商:AD 制造商全稱:Analog Devices 功能描述:18-Bit, 1.33 MSPS PulSAR 10.5 mW ADC in MSOP/QFN |
| AD79841 | 制造商:AD 制造商全稱:Analog Devices 功能描述:18-Bit, 2 MSPS PulSAR 15 mW ADC in LFCSP (QFN) |
| AD7984BCPZ | 制造商:AD 制造商全稱:Analog Devices 功能描述:18-Bit, 1.33 MSPS PulSAR 10.5 mW ADC in MSOP/QFN |
發布緊急采購，3分鐘左右您將得到回復。