- 您現在的位置：買賣IC網 > PDF目錄10301 > AD7938BCPZ-6REEL7 (Analog Devices Inc)IC ADC 12BIT 8CH 625KSPS 32LFCSP PDF資料下載
參數資料
| 型號： | AD7938BCPZ-6REEL7 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 22/32頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 12BIT 8CH 625KSPS 32LFCSP |
| 標準包裝： | 1,500 |
| 位數： | 12 |
| 采樣率（每秒）： | 625k |
| 數據接口： | 并聯 |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 7.5mW |
| 電壓電源： | 單電源 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 32-VFQFN 裸露焊盤，CSP |
| 供應商設備封裝： | 32-LFCSP-VQ |
| 包裝： | 帶卷 (TR) |
| 輸入數目和類型： | 8 個單端，單極；4 個差分，單極；4 個偽差分，單極；7 偽差分，單極 |
| 配用： | EVAL-AD7938CBZ-ND - EVAL BOARD FOR AD7938 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁當前第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
Data Sheet
AD7938-6
Rev. C | Page 29 of 32
APPLICATION HINTS
GROUNDING AND LAYOUT
The printed circuit board that houses the AD7938-6 should be
designed so that the analog and digital sections are separated
and confined to certain areas of the board. This facilitates the
use of ground planes that can be easily separated. Generally, a
minimum etch technique is best for ground planes since it gives
the best shielding. Digital and analog ground planes should be
joined in only one place, and the connection should be a star
ground point established as close to the ground pins on the
AD7938-6 as possible. Avoid running digital lines under the
device as this couples noise onto the die. The analog ground
plane should be allowed to run under the AD7938-6 to avoid
noise coupling. The power supply lines to the AD7938-6 should
use as large a trace as possible to provide low impedance paths
and reduce the effects of glitches on the power supply line.
Fast switching signals, such as clocks, should be shielded with
digital ground to avoid radiating noise to other sections of the
board, and clock signals should never run near the analog
inputs. Avoid crossover of digital and analog signals. Traces on
opposite sides of the board should run at right angles to each
other. This reduces the effects of feedthrough through the
board. A microstrip technique is by far the best but is not
always possible with a double-sided board. In this technique,
the component side of the board is dedicated to ground planes,
while signals are placed on the solder side.
Good decoupling is also important. All analog supplies should
be decoupled with 10 μF tantalum capacitors in parallel with
0.1 μF capacitors to GND. To achieve the best performance
from these decoupling components, they must be placed as
close as possible to the device, ideally right up against the
device. The 0.1 μF capacitors should have low effective series
resistance (ESR) and effective series inductance (ESI), such as
the common ceramic types or surface-mount types, which
provide a low impedance path to ground at high frequencies to
handle transient currents due to internal logic switching.
PCB DESIGN GUIDELINES FOR CHIP SCALE
PACKAGE
The lands on the chip scale package (CP-32-2) are rectangular.
The printed circuit board pad for these should be 0.1 mm
longer than the package land length and 0.05 mm wider than
the package land width. The land should be centered on the
pad. This ensures that the solder joint size is maximized. The
bottom of the chip scale package has a thermal pad. The
thermal pad on the printed circuit board should be at least as
large as this exposed pad. On the printed circuit board, there
should be a clearance of at least 0.25 mm between the thermal
pad and the inner edges of the pad pattern. This ensures that
shorting is avoided. Thermal vias can be used on the printed
circuit board thermal pad to improve thermal performance of
the package. If vias are used, they should be incorporated in the
thermal pad at 1.2 mm pitch grid. The via diameter should be
between 0.3 mm and 0.33 mm, and the via barrel should be
plated with 1 oz. copper to plug the via. The user should
connect the printed circuit board thermal pad to AGND.
EVALUATING THE AD7938-6 PERFORMANCE
The recommended layout for the AD7938-6 is outlined in the
evaluation board documentation. The evaluation board
package includes a fully assembled and tested evaluation board,
documentation, and software for controlling the board from the
PC via the evaluation board controller. The evaluation board
controller can be used in conjunction with the AD7938-6
evaluation board, as well as many other Analog Devices evaluation
boards ending in the CB designator, to demonstrate/evaluate
the ac and dc performance of the AD7938-6.
The software allows the user to perform ac (fast Fourier
transform) and dc (histogram of codes) tests on the AD7938-6.
The software and documentation are on the CD that ships with
the evaluation board.
相關PDF資料 |
PDF描述 |
|---|---|
| LTC2355CMSE-12#TRPBF | IC ADC 12BIT 3.5MSPS 10-MSOP |
| LTC2356CMSE-12#TRPBF | IC ADC 12BIT 3.5MSPS 10-MSOP |
| AD7887BR-REEL7 | IC ADC 12BIT 2CH SRL 8-SOIC |
| MS27497T18A32P | CONN RCPT 32POS WALL MNT W/PINS |
| AD7887BR-REEL | IC ADC 12BIT 2CH SRL 8-SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7938BCPZ-REEL7 | 功能描述:IC ADC 12BIT 8CH 1.5MSPS 32LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
| AD7938BSU | 制造商:Analog Devices 功能描述: |
| AD7938BSU-6 | 制造商:Analog Devices 功能描述:ADC Single SAR 625ksps 12-bit Parallel 32-Pin TQFP |
| AD7938BSU-6REEL | 制造商:AD 制造商全稱:Analog Devices 功能描述:8-Channel, 625 kSPS, 12-Bit Parallel ADCs with a Sequencer |
| AD7938BSU-6REEL7 | 制造商:Analog Devices 功能描述:ADC Single SAR 625ksps 12-bit Parallel 32-Pin TQFP T/R |
發布緊急采購，3分鐘左右您將得到回復。