- 您現在的位置：買賣IC網 > PDF目錄9712 > AD7877ACPZ-REEL7 (Analog Devices Inc)IC ADC 12BIT TOUCHSCREEN 32LFCSP PDF資料下載
參數資料
| 型號： | AD7877ACPZ-REEL7 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 8/45頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 12BIT TOUCHSCREEN 32LFCSP |
| 標準包裝： | 1,500 |
| 類型： | 電阻 |
| 觸摸面板接口： | 4 線 |
| 輸入數/鍵： | 1 TSC |
| 分辨率（位）： | 12 b |
| 評估套件： | 可供 |
| 數據接口： | 串行，SPI? |
| 數據速率/采樣率 (SPS，BPS)： | 125k |
| 電壓基準： | 外部，內部 |
| 電源電壓： | 2.7 V ~ 5.25 V |
| 電流 - 電源： | 1µA |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 32-VFQFN 裸露焊盤，CSP |
| 供應商設備封裝： | 32-LFCSP-VQ |
| 包裝： | 帶卷 (TR) |
| 配用： | EVAL-AD7877EBZ-ND - BOARD EVALUATION FOR AD7877 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁
Data Sheet
AD7877
Rev. D | Page 15 of 44
AUX3/GPIO4
BAT1
BAT2
AUX2/GPIO3
AUX1/GPIO2
12-BIT SUCCESSIVE
APPROXIMATION ADC
WITH TRACK-AND-HOLD
9 TO 1
I/P
MUX
TEMPERATURE
SENSOR
Y–
Y+
X–
X+
VCC
REF–
IN+
REF
INT/EXT
REF+
DUAL 3-1
MUX
X– Y– GND X+ Y+ VREF
03796-006
Figure 28. Analog Input Structure
The AD7877 can be set up to automatically convert either
specific input channels or a sequence of channels. The results of
the ADC conversions are stored in the results registers. See the
Serial Interface section for details.
When measuring the ancillary analog inputs (AUX1 to AUX3,
BAT1 and BAT2), the ADC uses the internal reference, or an
external reference applied to the VREF pin, and the measurement
is referred to GND.
MEASURING TOUCH SCREEN INPUTS
When measuring the touch screen inputs, it is possible to
measure using the internal (or external) reference, or to use the
touch screen excitation voltage as the reference and perform a
ratiometric, differential measurement. The differential method
is the default and is selected by clearing the SER/DFR bit
(Bit 11) in Control Register 1. The single-ended method is
selected by setting this bit.
Single-Ended Method
Figure 29 illustrates the single-ended method for the Y position.
For the X position, the excitation voltage is applied to X+ and
X and the voltage measured at Y+.
03796-007
ADC
REF+
INPUT
(VIA MUX)
X+
REF–
TOUCH
SCREEN
Y+
Y–
GND
VREF
VCC
Figure 29. Single-Ended Conversion of Touch Screen Inputs
The voltage seen at the input to the ADC in Figure 29 is
YTOTAL
Y
CC
IN
R
V
×
=
(1)
The advantage of the single-ended method is that the touch
screen excitation voltage can be switched off once the signal is
acquired. Because a screen can draw over 1 mA, this is a
significant consideration for a battery-powered system.
The disadvantages of the single-ended method are as follows:
It can be used only if VCC is close to VREF. If VCC is greater
than VREF, some positions on the screen are outside the
range of the ADC. If VCC is less than VREF, the full range of
the ADC is not used.
The ratio of VCC to VREF must be known. If VREF and/or VCC
vary relative to one another, this can introduce errors.
Voltage drops across the switches can introduce errors.
Touch screens can have a total end-to-end resistance
ranging from 200 to 900 . Taking the lowest screen
resistance of 200 and a typical switch resistance of 14
can reduce the apparent excitation voltage to 200/228 ×
100 = 87% of its actual value. In addition, the voltage drop
across the low-side switch adds to the ADC input voltage.
This introduces an offset into the input voltage, thus, it can
never reach zero.
The single-ended method is adequate for applications that use a
fairly blunt and imprecise instrument for an input device, such
as a finger.
Ratiometric Method
The ratiometric method illustrated in Figure 30 shows the
negative input of the ADC reference tied to Y and the positive
input connected to Y+. Thus, the screen excitation voltage
provides the reference for the ADC. The input of the ADC is
connected to X+ to determine the Y position.
03796-008
ADC
REF+
INPUT
(VIA MUX)
REF–
VCC
X+
TOUCH
SCREEN
Y+
Y–
GND
Figure 30. Ratiometric Conversion of Touch Screen Inputs
相關PDF資料 |
PDF描述 |
|---|---|
| SSTV16857CG | IC REGIST BUFF 14BIT DDR 48TSSOP |
| MS27497T24B35SC | CONN RCPT 128POS WALL MNT W/SCKT |
| AD7877ACBZ-REEL | IC CTRLR TOUCH SCREEN 25-WLCSP |
| MS27497E24F35S | CONN RCPT 128POS WALL MNT W/SCKT |
| MS3106R32-17PY | CONN PLUG 4POS STRAIGHT W/PINS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7877WACPZ-REEL7 | 功能描述:IC CTRLR TOUCH SCREEN 32LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 觸摸屏控制器 系列:- 標準包裝:96 系列:- 類型:- 觸摸面板接口:- 輸入數/鍵:- 分辨率（位）:- 評估套件:* 數據接口:- 數據速率/采樣率 (SPS，BPS):- 電壓基準:- 電源電壓:- 電流 - 電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:帶卷 (TR) |
| AD7878 | 制造商:AD 制造商全稱:Analog Devices 功能描述:LC2MOS Complete 12-Bit 100 kHz Sampling ADC with DSP Interface |
| AD7878AQ | 制造商:Rochester Electronics LLC 功能描述:COMPLETE 12 BIT ADC IC - Bulk |
| AD7878BQ | 功能描述:IC ADC 12BIT W/DSP INT 28-CDIP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:250 系列:- 位數:12 采樣率（每秒）:1.8M 數據接口:并聯 轉換器數目:1 功率耗散（最大）:1.82W 電壓電源:模擬和數字 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-LQFP 供應商設備封裝:48-LQFP（7x7） 包裝:管件 輸入數目和類型:2 個單端，單極 |
| AD7878JN | 制造商:Analog Devices 功能描述:ADC Single SAR 100ksps 12-bit Parallel 28-Pin PDIP W 制造商:Rochester Electronics LLC 功能描述:COMPLETE 12 BIT ADC IC - Bulk 制造商:Analog Devices 功能描述:LC2MOS Complete 12-Bit 100 kHz Sampling ADC with DSP Interface |
發布緊急采購，3分鐘左右您將得到回復。