- 您現在的位置：買賣IC網 > PDF目錄375240 > AD7859L (Analog Devices, Inc.) 3 V to 5 V Single Supply, 200 kSPS 8-Channel, 12-Bit Sampling ADCs(單電源,200kSPS 8通道12位采樣A/D轉換器) PDF資料下載
參數資料
| 型號： | AD7859L |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | 3 V to 5 V Single Supply, 200 kSPS 8-Channel, 12-Bit Sampling ADCs(單電源,200kSPS 8通道12位采樣A/D轉換器) |
| 中文描述： | 3 V至5 V單電源，200 kSPS的8通道，12位采樣ADC（單電源，速度高達200ksps的8通道12位采樣的A / D轉換器） |
| 文件頁數： | 9/28頁 |
| 文件大?。?/td> | 555K |
| 代理商： | AD7859L |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
AD7859/AD7859L
REV. A
–9–
CONTROL REGISTER
The arrangement of the control register is shown below. The control register is a write only register and contains 14 bits of data. The
control register is selected by putting two 1s in ADDR1 and ADDR0. The function of the bits in the control register is described
below. The power-up status of all bits is 0.
MSB
SGL/
DIFF
CHSLT2
CHSLT1
CHSLT0
PMGT1
PMGT0
RDSLT1
RDSLT0
AMODE
CONVST
CALMD
CALSLT1
CALSLT0
STCAL
LSB
CONTROL REGISTER BIT FUNCTION DESCRIPTION
Bit
Mnemonic
Comment
13
SGL/
DIFF
A 0 in this bit position configures the input channels for pseudo-differential mode. A 1 in this bit posi-
tion configures the input channels in single ended mode. Please see Table III for channel selection.
These three bits are used to select the analog input on which the conversion is performed. The analog
inputs can be configured as eight single-ended channels or four pseudo-differential channels. The
default selection is AIN1 for the positive input and AIN2 for the negative input. Please see Table III for
channel selection information.
Power Management Bits. These two bits are used with the
SLEEP
pin for putting the part into various
Power-Down modes (See
Power-Down
section for more details).
Theses two bits determine which register is addressed for the read operations. Please see Table II.
12
11
10
CHSLT2
CHSLT1
CHSLT0
9
8
7
6
5
PMGT1
PMGT0
RDSLT1
RDSLT0
AMODE
Analog Mode Bit. This bit has two different functions, depending on the status of the SGL/
DIFF
bit.
When SGL/
DIFF
is 0, AMODE selects between unipolar and bipolar analog input ranges. A logic 0 in
this bit position selects the unipolar range, 0 to V
REF
(i.e., AIN(+) – AIN(–) = 0 to V
REF
). A logic 1 in
this bit position selects the bipolar range –V
REF
/2 to +V
REF
/2 (i.e., AIN(+) – AIN(–) = –V
REF
/2 to
+V
REF
/2). In this case AIN(–) needs to be tied to at least +V
REF
/2 to allow AIN(+) to have a full input
swing from 0 V to +V
REF
.
When SGL/
DIFF
is 1, AMODE selects the source for the AIN(–) channel of the sample and hold cir-
cuitry. If AMODE is a 0, AGND is selected. If AMODE is a 1, then AIN8 is selected. Please see
Table III for more information.
Conversion Start Bit. A logic 1 in this bit position starts a single conversion, and this bit is automatically
reset to 0 at the end of conversion. This bit may also be used in conjunction with system calibration (see
calibration section on page 21).
Calibration Mode Bit. A 0 here selects self-calibration and a 1 selects a system calibration (see Table IV).
Calibration Selection Bits 1 and 0. These bits have two functions, depending on the STCAL bit.
With the STCAL bit set to 1, the CALSLT1 and CALSLT0 bits, along with the CALMD bit, deter-
mine the type of calibration performed by the part (see Table IV).
With the STCAL bit set to 0, the CALSLT1 and CALSLT0 bits are decoded to address the calibration
register for read/write of calibration coefficients (see Table V for more details).
Start Calibration Bit. When STCAL is set to a 1, a calibration is performed, as determined by the
CALMD, CALSLT1 and CALSLT0 bits. Please see Table IV. When STCAL is set to a zero, no cali-
bration is performed.
4
CONVST
3
2
1
CALMD
CALSLT1
CALSLT0
0
STCAL
相關PDF資料 |
PDF描述 |
|---|---|
| AD7859 | 3 V to 5 V Single Supply, 200 kSPS 8-Channel, 12-Bit Sampling ADCs(單電源,200kSPS 8通道12位采樣A/D轉換器) |
| AD7861AP | 11-Bit Resolution Simultaneous Sampling A/D Converter |
| AD7861 | 11-Bit Resolution Simultaneous Sampling A/D Converter(同時采樣11位A/D轉換器) |
| AD7862 | Simultaneous Sampling Dual 250 kSPS 12-Bit ADC(同時采樣250kSPS 12位雙A/D轉換器) |
| AD7863 | Simultaneous Sampling Dual 175 kSPS 14-Bit ADC(同時采樣175kSPS14位雙A/D轉換器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7859LAS | 制造商:Analog Devices 功能描述:ADC Single SAR 100ksps 12-bit Parallel 44-Pin MQFP 制造商:Rochester Electronics LLC 功能描述:12-BIT 8 CH.PARALLEL 100 KSPS I.C. - Bulk 制造商:Analog Devices 功能描述:IC 12-BIT ADC |
| AD7859LAS3 | 制造商:AD 制造商全稱:Analog Devices 功能描述:3 V to 5 V Single Supply, 200 kSPS8-Channel, 12-Bit Sampling ADCs |
| AD7859LAS-REEL | 制造商:Analog Devices 功能描述:ADC Single SAR 100ksps 12-bit Parallel 44-Pin MQFP T/R |
| AD7859LASZ | 功能描述:IC ADC 12BIT 8CH 200KSPS 44-MQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
發(fā)布緊急采購，3分鐘左右您將得到回復。