參數資料
型號： AD7851ANZ
廠商： Analog Devices Inc
文件頁數： 21/36頁
文件大小： 0K
描述： IC ADC 14BIT SRL 333KSPS 24-DIP
產品變化通告： Product Discontinuance 27/Oct/2011
標準包裝： 15
位數： 14
采樣率（每秒）： 333k
數據接口： 8051，QSPI?，串行，SPI? µP
轉換器數目： 2
功率耗散（最大）： 89.25mW
電壓電源： 模擬和數字
工作溫度： -40°C ~ 85°C
安裝類型： 通孔
封裝/外殼： 24-DIP（0.300"，7.62mm）
供應商設備封裝： 24-PDIP
包裝： 管件
輸入數目和類型： 1 個偽差分，單極；1 個偽差分，雙極
AD7851
–28–
REV. B
If the user has control of the
CONVST pin but does not want to
exercise it for every conversion, the control register may be used
to start a conversion. Setting the
CONVST bit in the control
register to 1 starts a conversion. If the user does not have con-
trol of the
CONVST pin, a conversion should not be initiated
by writing to the control register. The reason for this is that the
user may get locked out and not be able to perform any further
write/read operations. When a conversion is started by writing to
the control register, the
SYNC goes low and read/write opera-
tions take place while the conversion is in progress. However,
once the conversion is complete, there is no way of writing to
the part unless the
CONVST pin is exercised. The CONVST
signal triggers the
SYNC signal low which allows read/write
operations to take place.
SYNC must be low to perform read/
write operations. The
SYNC is triggered low by the CONVST
signal rising edge or by setting the
CONVST bit in the control
register to 1. Therefore, if there is not full control of the
CONVST pin, the user may become locked out.
SERIAL
INTERFACE
MODE
?
POWER ON, APPLY CLKIN SIGNAL,
WAIT FOR AUTOMATIC CALIBRATION
DIN CONNECTED TO DGND
NO
YES
START
WAIT FOR BUSY SIGNAL
TO GO LOW
PULSE
CONVST PIN
READ
DATA
DURING
CONVERSION
?
WAIT APPROXIMATELY 200ns
AFTER
CONVST RISING EDGE
APPLY
SYNC (IF REQUIRED), SCLK, AND READ
CONVERSION RESULT ON DOUT PIN
PULSE
CONVST PIN
SYNC AUTOMATICALLY GOES LOW
AFTER
CONVST RISING EDGE
SCLK AUTOMATICALLY ACTIVE, READ
CONVERSION RESULT ON DOUT PIN
4, 5
2, 3
Figure 40. Flowchart for Setting Up and Reading from the AD7851
CONFIGURING THE AD7851
AD7851 as a Read-Only ADC
The AD7851 contains 14 on-chip registers that can be accessed
via the serial interface. In the majority of applications, it will not
be necessary to access all of these registers. Figure 40 outlines the
sequence used to configure the AD7851 as a read-only ADC. In
this case, there is no writing to the on-chip registers and only the
conversion result data is read from the part. Interface Mode 1
cannot be used in this case as it is necessary to write to the con-
trol register to set Interface Mode 1. Here the CLKIN signal is
applied directly after power-on; the CLKIN signal must be
present to allow the part to perform a calibration. This automatic
calibration will be completed approximately 42 ms after the
AD7851 has powered up (6 MHz CLK).
相關PDF資料
PDF描述
AD7853BNZ IC ADC 12BIT SRL 200KSPS 24-DIP
AD7854BRZ IC ADC 12BIT PARALLEL LP 28-SOIC
AD7856ARZ-REEL7 IC ADC 14BIT 8CHAN 5V 24SOIC
AD7858LBNZ IC ADC 12BIT 8CHAN SRL 24DIP
AD7859BSZ IC ADC 12BIT 8CHAN LP 44-MQFP
相關代理商/技術參數
參數描述
AD7851AR 制造商:Analog Devices 功能描述:ADC Single SAR 333ksps 14-bit Serial 24-Pin SOIC W 制造商:Rochester Electronics LLC 功能描述:14 BIT SELF CALIBRATION ADC I.C. - Bulk
AD7851AR-REEL 制造商:Analog Devices 功能描述:ADC Single SAR 333ksps 14-bit Serial 24-Pin SOIC W T/R
AD7851ARS 制造商:Analog Devices 功能描述:ADC Single SAR 333ksps 14-bit Serial 24-Pin SSOP 制造商:Analog Devices 功能描述:IC 14-BIT ADC
AD7851ARS-REEL 制造商:Analog Devices 功能描述:ADC Single SAR 333ksps 14-bit Serial 24-Pin SSOP T/R
AD7851ARSZ 功能描述:IC ADC 14BIT SRL 333KSPS 24SSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*