- 您現在的位置：買賣IC網 > PDF目錄5689 > AD783JR (Analog Devices Inc)IC AMP SAMPLE HOLD LP 5MA 8SOIC PDF資料下載
參數資料
| 型號： | AD783JR |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 7/8頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC AMP SAMPLE HOLD LP 5MA 8SOIC |
| 標準包裝： | 1 |
| 放大器類型： | 采樣和保持 |
| 電路數： | 1 |
| -3db帶寬： | 15MHz |
| 電流 - 輸入偏壓： | 100nA |
| 電流 - 電源： | 9.5mA |
| 電流 - 輸出 / 通道： | 5mA |
| 電壓 - 電源，單路/雙路(±)： | ±4.75 V ~ 5.25 V |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 8-SO |
| 包裝： | 管件 |
AD783
REV. A
–7–
The AD783 does not provide separate analog and digital ground
leads as is the case with most A-to-D converters. The common
pin is the single ground terminal for the device. It is the refer-
ence point for the sampled input voltage and the held output
voltage and also the digital ground return path. The common
pin should be connected to the reference (analog) ground of the
A-to-D converter with a separate ground lead. Since the analog
and digital grounds in the AD783 are connected internally, the
common pin should also be connected to the digital ground,
which is usually tied to analog common at the A-to-D converter.
Figure 3 illustrates the recommended decoupling and grounding
practice.
NOISE CHARACTERISTICS
Designers of data conversion circuits must also consider the
effect of noise sources on the accuracy of the data acquisition
system. A sample-and-hold amplifier that precedes the A-to-D
converter introduces some noise and represents another source
of uncertainty in the conversion process. The noise from the
AD783 is specified as the total output noise, which includes
both the sampled wideband noise of the SHA in addition to the
band limited output noise. The total output noise is the rms
sum of the sampled dc uncertainty and the hold mode noise. A
plot of the total output noise vs. the equivalent input bandwidth
of the converter being used is given in Figure 4.
300
0
1k
10M
200
100
10k
1M
100k
FREQUENCY – Hz
OUTPUT
NOISE
–
V
rms
Figure 4. RMS Noise vs. Input Bandwidth of ADC
DRIVING THE ANALOG INPUTS
For best performance, it is important to drive the AD783 analog
input from a low impedance signal source. This enhances the
sampling accuracy by minimizing the analog and digital cross-
talk. Signals which come from higher impedance sources (e.g.,
over 5 k
) will have a relatively higher level of crosstalk. For
applications where signals have high source impedance, an
operational amplifier buffer in front of the AD783 is required.
The AD711 (precision BiFET op amp) is recommended for
these applications.
HIGH FREQUENCY SAMPLING
Aperture jitter and distortion are the primary factors which limit
frequency domain performance of a sample-and-hold amplifier.
Aperture jitter modulates the phase of the hold command and
produces an effective noise on the sampled analog input. The
magnitude of the jitter induced noise is directly related to the
frequency of the input signal.
A graph showing the magnitude of the jitter induced error vs.
frequency of the input signal is given in Figure 5.
The accuracy in sampling high frequency signals is also
constrained by the distortion and noise created by the
sample-and-hold. The level of distortion increases with
frequency and reduces the “effective number of bits” of the
conversion.
Measurements of Figures 6 and 7 were made using a 14-bit
A/D converter with VIN = 5 V p-p and a sample frequency of
100 kSPS.
1%
1k
1M
0.1%
0.01%
10k
100k
FREQUENCY – Hz
APERTURE JITTER TYPICAL AT 20ps
1/2 BIT @
8 BITS
1/2 BIT @
10 BITS
1/2 BIT @
12 BITS
1/2 BIT @
14 BITS
Figure 5. Error Magnitude vs. Frequency
–65
–95
1M
–80
–90
1k
–85
100
–70
–75
100k
10k
FREQUENCY – Hz
THD
–
dB
Figure 6. Total Harmonic Distortion vs. Frequency
90
0
1M
20
10
10k
1k
30
40
50
60
70
80
100k
FREQUENCY – Hz
S/(N
+
D)
–
dB
Figure 7. Signal/(Noise and Distortion) vs. Frequency
相關PDF資料 |
PDF描述 |
|---|---|
| 100NH2G-690 | FUSE 100A 690V CLASS GL/GG |
| 925320-01-14-10 | CONN HEADER 14POS DL .100" GOLD |
| TV02W360-G | TVS 200W 36V UNIDIRECT SOD-123 |
| TV02W330-HF | TVS 200W 33V UNIDIRECT SOD-123 |
| TV02W330-G | TVS 200W 33V UNIDIRECT SOD-123 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD783JRZ | 功能描述:IC AMP SAMPLE HOLD LP 5MA 8SOIC RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:2,500 系列:- 放大器類型:通用 電路數:4 輸出類型:- 轉換速率:0.6 V/µs 增益帶寬積:1MHz -3db帶寬:- 電流 - 輸入偏壓:45nA 電壓 - 輸入偏移:2000µV 電流 - 電源:1.4mA 電流 - 輸出 / 通道:40mA 電壓 - 電源，單路/雙路(±):3 V ~ 32 V，±1.5 V ~ 16 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:14-TSSOP 包裝:帶卷 (TR) 其它名稱:LM324ADTBR2G-NDLM324ADTBR2GOSTR |
| AD783SQ | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Sample/Track-and-Hold Amplifier |
| AD783SQ/883B | 制造商:Rochester Electronics LLC 功能描述:IC, 12-BIT 250 NS S/H AMP - Bulk |
| AD7840 | 制造商:AD 制造商全稱:Analog Devices 功能描述:LC2MOS Complete 14-Bit DAC |
| AD7840AQ | 制造商:Analog Devices 功能描述: 制造商:Rochester Electronics LLC 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。