- 您現在的位置：買賣IC網 > PDF目錄10270 > AD7822BRUZ (Analog Devices Inc)IC ADC 8BIT PAR 2MSPS 20TSSOP PDF資料下載
參數資料
| 型號： | AD7822BRUZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 27/28頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 8BIT PAR 2MSPS 20TSSOP |
| 標準包裝： | 75 |
| 位數： | 8 |
| 采樣率（每秒）： | 2M |
| 數據接口： | 并聯 |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 36mW |
| 電壓電源： | 單電源 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 20-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 20-TSSOP |
| 包裝： | 管件 |
| 輸入數目和類型： | 1 個單端，單極 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁當前第27頁第28頁
AD7822/AD7825/AD7829
Rev. C | Page 8 of 28
TERMINOLOGY
Signal-to-(Noise + Distortion) Ratio
The measured ratio of signal-to-(noise + distortion) at the
output of the analog-to-digital converter. The signal is the rms
amplitude of the fundamental. Noise is the rms sum of all
nonfundamental signals up to half the sampling frequency
(fS/2), excluding dc. The ratio is dependent upon the number of
quantization levels in the digitization process: the more levels,
the smaller the quantization noise. The theoretical signal-to-(noise
+ distortion) ratio for an ideal N-bit converter with a sine wave
input is given by
Signal-to-(Noise + Distortion) = (6.02 N + 1.76) dB
Thus, for an 8-bit converter, this is 50 dB.
Total Harmonic Distortion (THD)
The ratio of the rms sum of harmonics to the fundamental. For
the AD7822/AD7825/AD7829, it is defined as
1
6
5
3
2
V
THD
2
4
2
log
20
(dB)
+
=
where V1 is the rms amplitude of the fundamental and V2, V3,
V4, V5, and V6 are the rms amplitudes of the second through the
sixth harmonics.
Peak Harmonic or Spurious Noise
The ratio of the rms value of the next largest component in the
ADC output spectrum (up to fS/2 and excluding dc) to the rms
value of the fundamental. Normally, the value of this specification
is determined by the largest harmonic in the spectrum, but for
parts where the harmonics are buried in the noise floor, it is a
noise peak.
Intermodulation Distortion
With inputs consisting of sine waves at two frequencies, fa and
fb, any active device with nonlinearities creates distortion
products at sum and difference frequencies of mfa ± nfb, where
m, n = 0, 1, 2, 3, … . Intermodulation terms are those for which
neither m nor n is equal to zero. For example, the second-order
terms include (fa + fb) and (fa fb), and the third-order terms
include (2fa + fb), (2fa fb), (fa + 2fb), and (fa 2fb).
The AD7822/AD7825/AD7829 are tested using the CCIF
standard, where two input frequencies near the top end of the
input bandwidth are used. In this case, the second- and third-
order terms are of different significance. The second-order terms
are usually distanced in frequency from the original sine waves,
and the third-order terms are usually at a frequency close to the
input frequencies. As a result, the second- and third-order terms
are specified separately. The calculation of the intermodulation
distortion is as per the THD specification, where it is the ratio
of the rms sum of the individual distortion products to the rms
amplitude of the fundamental expressed in decibels (dB).
Channel-to-Channel Isolation
A measure of the level of crosstalk between channels. It is
measured by applying a full-scale 20 kHz sine wave signal to
one input channel and determining how much that signal is
attenuated in each of the other channels. The figure given is the
worst case across all four or eight channels of the AD7825 and
AD7829, respectively.
Relative Accuracy or Endpoint Nonlinearity
The maximum deviation from a straight line passing through
the endpoints of the ADC transfer function.
Differential Nonlinearity
The difference between the measured and the ideal one LSB
change between any two adjacent codes in the ADC.
Offset Error
The deviation of the 128th code transition (01111111) to
(10000000) from the ideal, that is, VMID.
Offset Error Match
The difference in offset error between any two channels.
Zero-Scale Error
The deviation of the first code transition (00000000) to
(00000001) from the ideal; that is, VMID 1.25 V + 1 LSB (VDD =
5 V ± 10%), or VMID 1.0 V + 1 LSB (VDD = 3 V ± 10%).
Full-Scale Error
The deviation of the last code transition (11111110) to (11111111)
from the ideal; that is, VMID + 1.25 V 1 LSB (VDD = 5 V ± 10%),
or VMID + 1.0 V 1 LSB (VDD = 3 V ± 10%).
相關PDF資料 |
PDF描述 |
|---|---|
| MS27499E14F35SB | CONN RCPT 37POS BOX MNT W/SCKT |
| VE-23Z-MV-S | CONVERTER MOD DC/DC 2V 60W |
| VI-JNP-MX-S | CONVERTER MOD DC/DC 13.8V 75W |
| MS27499E14B35SC | CONN RCPT 37POS BOX MNT W/SCKT |
| D38999/20KD97SNLC | CONN HSG RCPT 12POS WALL MT SCKT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7822BRUZ1 | 制造商:AD 制造商全稱:Analog Devices 功能描述:3 V/5 V, 2 MSPS, 8-Bit, 1-/4-/8-Channel Sampling ADCs |
| AD7822BRUZ-REEL | 功能描述:IC ADC 8BIT 1CHAN 2MSPS 20TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 位數:12 采樣率（每秒）:3M 數據接口:- 轉換器數目:- 功率耗散（最大）:- 電壓電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-23-6 包裝:帶卷 (TR) 輸入數目和類型:- |
| AD7822BRUZ-REEL1 | 制造商:AD 制造商全稱:Analog Devices 功能描述:3 V/5 V, 2 MSPS, 8-Bit, 1-/4-/8-Channel Sampling ADCs |
| AD7822BRUZ-REEL7 | 功能描述:IC ADC 8BIT 1CHAN 2MSPS 20TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| AD7822BRUZ-REEL71 | 制造商:AD 制造商全稱:Analog Devices 功能描述:3 V/5 V, 2 MSPS, 8-Bit, 1-/4-/8-Channel Sampling ADCs |
發布緊急采購，3分鐘左右您將得到回復。