- 您現在的位置：買賣IC網 > PDF目錄10259 > AD7794BRU-REEL (Analog Devices Inc)IC ADC 24BIT 6CH LP 24-TSSOP PDF資料下載
參數資料
| 型號： | AD7794BRU-REEL |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 25/37頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 24BIT 6CH LP 24-TSSOP |
| 標準包裝： | 2,500 |
| 位數： | 24 |
| 采樣率（每秒）： | 470 |
| 數據接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 2.5mW |
| 電壓電源： | 模擬和數字 |
| 工作溫度： | -40°C ~ 105°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 24-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 24-TSSOP |
| 包裝： | 帶卷 (TR) |
| 輸入數目和類型： | 6 個差分，單極；6 個差分，雙極 |
| 配用： | EVAL-AD7794EBZ-ND - BOARD EVALUATION FOR AD7794 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁當前第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁
AD7794/AD7795
Rev. D | Page 30 of 36
Single Conversion Mode
In single conversion mode, the AD7794/AD7795 are placed in
shutdown mode between conversions. When a single
conversion is initiated by setting MD2 to 0, MD1 to 0, and MD0
to 1 in the mode register, the AD7794/AD7795 power up,
perform a single conversion, and then return to shutdown
mode. The on-chip oscillator requires 1 ms to power up. A
conversion requires a time period of 2 × tADC. DOUT/RDY goes
low to indicate the completion of a conversion. When the data-
word has been read from the data register, DOUT/RDY goes
high. If CS is low, DOUT/RDY remains high until another
conversion is initiated and completed. The data register can be
read several times, if required, even when DOUT/RDY has
gone high.
Continuous Conversion Mode
This is the default power-up mode. The AD7794/AD7795
continuously convert with the RDY pin in the status register
going low each time a conversion is complete. If CS is low, the
DOUT/RDY line also goes low when a conversion is complete.
To read a conversion, the user writes to the communications
register, indicating that the next operation is a read of the data
register. The digital conversion is placed on the DOUT/RDY
pin as soon as SCLK pulses are applied to the ADC. DOUT/RDY
returns high when the conversion is read. The user can read this
register additional times, if required. However, the user must
ensure that the data register is not being accessed at the completion
of the next conversion, or else the new conversion word is lost.
Continuous Read
Rather than write to the communications register each time a
conversion is complete to access the data, the AD7794/AD7795
can be configured so that the conversions are placed on the
DOUT/RDY line automatically. By writing 01011100 to the
communications register, the user need only apply the
appropriate number of SCLK cycles to the ADC. The 24-bit
word is automatically placed on the DOUT/RDY line when a
conversion is complete. The ADC should be configured for
continuous conversion mode.
When DOUT/RDY goes low to indicate the end of a conversion,
sufficient SCLK cycles must be applied to the ADC, and the
data conversion is placed on the DOUT/RDY line. When the
conversion is read, DOUT/RDY returns high until the next
conversion is available.
In this mode, the data can be read only once. Also, the user must
ensure that the data-word is read before the next conversion is
complete. If the user has not read the conversion before the
completion of the next conversion, or if insufficient serial clocks are
applied to the AD7794/AD7795 to read the word, the serial
output register is reset when the next conversion is complete.
The new conversion is then placed in the output serial register.
To exit the continuous read mode, the instruction 01011000
must be written to the communications register while the RDY
pin is low. While in the continuous read mode, the ADC
monitors activity on the DIN line so that it can receive the
instruction to exit the continuous read mode. Additionally, a
reset occurs if 32 consecutive 1s are seen on DIN. Therefore,
DIN should be held low in continuous read mode until an
instruction is to be written to the device.
相關PDF資料 |
PDF描述 |
|---|---|
| D38999/26KJ4BN | CONN HSG PLUG 56POS STRGHT SCKT |
| VE-23X-CU-F2 | CONVERTER MOD DC/DC 5.2V 200W |
| D38999/26WJ7SBLC | CONN HSG PLUG 99POS STRGHT SCKT |
| D38999/26KJ24AN | CONN HSG PLUG 24POS STRGHT PINS |
| VE-23X-CU-F1 | CONVERTER MOD DC/DC 5.2V 200W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7794BRUZ | 功能描述:IC ADC 24BIT SIG-DEL 6CH 24TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
| AD7794BRUZ1 | 制造商:AD 制造商全稱:Analog Devices 功能描述:6-Channel, Low Noise, Low Power, 24-/16-Bit ?￡-?? ADC with On-Chip In-Amp and Reference |
| AD7794BRUZ-REEL | 功能描述:IC ADC 24BIT 6CH LP 24-TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| AD7794BRUZ-REEL1 | 制造商:AD 制造商全稱:Analog Devices 功能描述:6-Channel, Low Noise, Low Power, 24-/16-Bit ?￡-?? ADC with On-Chip In-Amp and Reference |
| AD7794CRU | 制造商:Analog Devices 功能描述:AFE 6CH 24/16BIT 470HZ 24T 制造商:Analog Devices 功能描述:AFE, 6CH, 24/16BIT, 470HZ, 24TSSOP; IC Function:Analogue Front End Device IC; Supply Voltage Min:2.7V; Supply Voltage Max:5.25V; Operating Temperature Min:-40C; Operating Temperature Max:125C; Digital IC Case Style:TSSOP; No. of ;RoHS Compliant: Yes |
發布緊急采購，3分鐘左右您將得到回復。