參數資料
型號: AD7793BRUZ-REEL
廠商: Analog Devices Inc
文件頁數: 17/33頁
文件大?。?/td> 0K
描述: IC ADC 24BIT 3CH LP 16-TSSOP
設計資源: Fully Isolated Input Module Based on AD7793 and ADuM5401(CN0066)
Fully Isolated Input Module Based on AD7793, ADuM5401, and a High Performance In-Amp (CN0067)
標準包裝: 2,500
位數: 24
采樣率(每秒): 500
數據接口: DSP,MICROWIRE?,QSPI?,串行,SPI?
轉換器數目: 1
功率耗散(最大): 2.5mW
電壓電源: 模擬和數字
工作溫度: -40°C ~ 105°C
安裝類型: 表面貼裝
封裝/外殼: 16-TSSOP(0.173",4.40mm 寬)
供應商設備封裝: 16-TSSOP
包裝: 帶卷 (TR)
輸入數目和類型: 3 個差分,單極;3 個差分,雙極
配用: EVAL-AD7793EBZ-ND - BOARD EVALUATION FOR AD7793
AD7792/AD7793
Rev. B | Page 23 of 32
Continuous Read
Rather than write to the communications register each time a
conversion is complete to access the data, the AD7792/AD7793
can be configured so that the conversions are placed on the
DOUT/RDY line automatically. By writing 01011100 to the
communications register, the user needs only to apply the
appropriate number of SCLK cycles to the ADC, and the 16/24-
bit word is automatically placed on the DOUT/RDY line when a
conversion is complete. The ADC should be configured for
continuous conversion mode.
When DOUT/RDY goes low to indicate the end of a conver-
sion, sufficient SCLK cycles must be applied to the ADC, and
the data conversion is placed on the DOUT/RDY line. When
the conversion is read, DOUT/RDY returns high until the next
conversion is available. In this mode, the data can be read only
once. In addition, the user must ensure that the data-word is
read before the next conversion is complete. If the user has not
read the conversion before the completion of the next
conversion, or if insufficient serial clocks are applied to the
AD7792/AD7793 to read the word, the serial output register is
reset when the next conversion is completed, and the new
conversion is placed in the output serial register.
To exit the continuous read mode, the instruction 01011000
must be written to the communications register while the
DOUT/RDY pin is low. While in the continuous read mode, the
ADC monitors activity on the DIN line so that it can receive the
instruction to exit the continuous read mode. Additionally, a
reset occurs if 32 consecutive 1s are seen on DIN. Therefore,
DIN should be held low in continuous read mode until an
instruction is written to the device.
04855-
017
DIN
SCLK
DOUT/RDY
CS
0x5C
DATA
Figure 19. Continuous Read
相關PDF資料
PDF描述
MS27497E10A13S CONN RCPT 13POS WALL MNT W/SCKT
AD7813YNZ IC ADC 10BIT PARALLEL 16-DIP
AD7708BRZ-REEL7 IC ADC 16BIT R-R 8/10CH 28SOIC
CS3100A-14S-78P CONN RCPT 2POS WALL MNT W/PINS
AD7366BRUZ-5-RL7 IC ADC 12BIT DUAL BIPO 24-TSSOP
相關代理商/技術參數
參數描述
AD7793BRUZ-REEL1 制造商:AD 制造商全稱:Analog Devices 功能描述:3-Channel, Low Noise, Low Power, 16-/24-Bit ?£-?? ADC with On-Chip In-Amp and Reference
AD7794 制造商:AD 制造商全稱:Analog Devices 功能描述:Low Power, 24-Bit Sigma-Delta ADC with In-Amp and Embedded Reference (6 Channel)
AD7794_07 制造商:AD 制造商全稱:Analog Devices 功能描述:6-Channel, Low Noise, Low Power, 24-/16-Bit ?£-?? ADC with On-Chip In-Amp and Reference
AD7794BRU 功能描述:IC ADC 24BIT 6CH LP 24-TSSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率(每秒):300k 數據接口:并聯 轉換器數目:1 功率耗散(最大):75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC(0.295",7.50mm 寬) 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端,單極;1 個單端,雙極
AD7794BRU-REEL 功能描述:IC ADC 24BIT 6CH LP 24-TSSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率(每秒):45k 數據接口:串行 轉換器數目:2 功率耗散(最大):315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC(0.295",7.50mm 寬) 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端,單極