參數資料
型號： AD7790BRMZ
廠商： Analog Devices Inc
文件頁數： 6/20頁
文件大?。?/td> 0K
描述： IC ADC 16BIT SIGMA-DELTA 10-MSOP
標準包裝： 50
位數： 16
采樣率（每秒）： 120
數據接口： DSP，MICROWIRE?，QSPI?，串行，SPI?
轉換器數目： 1
功率耗散（最大）： 230µW
電壓電源： 單電源
工作溫度： -40°C ~ 105°C
安裝類型： 表面貼裝
封裝/外殼： 10-TFSOP，10-MSOP（0.118"，3.00mm 寬）
供應商設備封裝： 10-MSOP
包裝： 管件
輸入數目和類型： 1 個差分，雙極
產品目錄頁面： 779 (CN2011-ZH PDF)
AD7790
Data Sheet
Rev. A | Page 14 of 20
DIGITAL INTERFACE
As previously outlined, the AD7790’s programmable functions
are controlled using a set of on-chip registers. Data is written to
these registers via the part’s serial interface and read access to
the on-chip registers is also provided by this interface. All
communications with the part must start with a write to the
communications register. After power-on or reset, the device
expects a write to its communications register. The data written
to this register determines whether the next operation is a read
operation or a write operation and also determines to which
register this read or write operation occurs. Therefore, write
access to any of the other registers on the part begins with a
write operation to the communications register followed by a
write to the selected register. A read operation from any other
register (except when continuous read mode is selected) starts
with a write to the communications register followed by a read
operation from the selected register.
The AD7790’s serial interface consists of four signals: CS, DIN,
SCLK, and DOUT/RDY. The DIN line is used to transfer data
into the on-chip registers while DOUT/RDY is used for access-
ing from the on-chip registers. SCLK is the serial clock input for
the device and all data transfers (either on DIN or DOUT/RDY)
occur with respect to the SCLK signal. The DOUT/ RDY pin
operates as a Data Ready signal also, the line going low when a
new data-word is available in the output register. It is reset high
when a read operation from the data register is complete. It also
goes high prior to the updating of the data register to indicate
when not to read from the device to ensure that a data read is
not attempted while the register is being updated. CS is used to
select a device. It can be used to decode the AD7790 in systems
where several components are connected to the serial bus.
Figure 3 and Figure 4 show timing diagrams for interfacing to
the AD7790 with CS being used to decode the part. Figure 3
shows the timing for a read operation from the AD7790’s output
shift register while Figure 4 shows the timing for a write opera-
tion to the input shift register. In all modes except continuous
read mode, it is possible to read the same word from the data
register several times even though the DOUT/RDY line returns
high after the first read operation. However, care must be taken
to ensure that the read operations have been completed before
the next output update occurs. In continuous read mode, the
data register can be read only once.
The serial interface can operate in 3-wire mode by tying CS low.
In this case, the SCLK, DIN, and DOUT/RDY lines are used to
communicate with the AD7790. The end of the conversion can
be monitored using the RDY bit in the status register. This
scheme is suitable for interfacing to microcontrollers. If CS is
required as a decoding signal, it can be generated from a port
pin. For microcontroller interfaces, it is recommended that
SCLK idles high between data transfers.
The AD7790 can be operated with CS being used as a frame
synchronization signal. This scheme is useful for DSP interfac-
es. In this case, the first bit (MSB) is effectively clocked out by
CS since CS would normally occur after the falling edge of
SCLK in DSPs. The SCLK can continue to run between data
transfers, provided the timing numbers are obeyed.
The serial interface can be reset by writing a series of 1s on the
DIN input. If a Logic 1 is written to the AD7790 line for at least
32 serial clock cycles, the serial interface is reset. This ensures
that in 3-wire systems, the interface can be reset to a known
state if the interface gets lost due to a software error or some
glitch in the system. Reset returns the interface to the state in
which it is expecting a write to the communications register.
This operation resets the contents of all registers to their power-
on values.
The AD7790 can be configured to continuously convert or to
perform a single conversion. See Figure 8 through Figure 10.
相關PDF資料
PDF描述
AD8611AR-REEL IC COMP SNGL 4NS ULTRFAST 8-SOIC
AD7789BRMZ IC ADC 24BIT LP 10-MSOP
LT1720CS8#TR IC COMP DUAL R-R 4MA 4.5NS 8SOIC
LTC1445IS#TRPBF IC COMP W/REF LOWPWR QUAD 16SOIC
CS5530-ISZ IC ADC 24BIT 1CH W/LNA 20SSOP
相關代理商/技術參數
參數描述
AD7790BRMZ 制造商:Analog Devices 功能描述:IC 24-BIT ADC
AD7790BRMZ-REEL 功能描述:IC ADC 16BIT SIGMA-DELTA 10-MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:2,500 系列:- 位數:16 采樣率（每秒）:15 數據接口:MICROWIRE?，串行，SPI? 轉換器數目:1 功率耗散（最大）:480µW 電壓電源:單電源 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:38-WFQFN 裸露焊盤 供應商設備封裝:38-QFN（5x7） 包裝:帶卷 (TR) 輸入數目和類型:16 個單端，雙極；8 個差分，雙極 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494
AD7791 制造商:AD 制造商全稱:Analog Devices 功能描述:Low Power, Buffered 24-Bit Sigma-Delta ADC
AD7791BRM 功能描述:IC ADC 24BIT BUFFERED LP 10MSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極
AD7791BRM-REEL 制造商:Analog Devices 功能描述:ADC Single Delta-Sigma 120sps 24-bit Serial 10-Pin MSOP T/R 制造商:Analog Devices 功能描述:ADC SGL DELTA-SIGMA 0.12KSPS 24BIT SERL 10MSOP - Tape and Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*