VREF+ INPUT SIGNAL The AD7767/AD" />
參數資料
型號: AD7767BRUZ
廠商: Analog Devices Inc
文件頁數: 16/25頁
文件大?。?/td> 0K
描述: ADC 24BIT 128KSPS SAR 16-TSSOP
標準包裝: 1
位數: 24
采樣率(每秒): 128k
數據接口: 串行
轉換器數目: 1
功率耗散(最大): 18mW
電壓電源: 模擬和數字
工作溫度: -40°C ~ 105°C
安裝類型: 表面貼裝
封裝/外殼: 16-TSSOP(0.173",4.40mm 寬)
供應商設備封裝: 16-TSSOP
包裝: 管件
輸入數目和類型: 1 個差分,單極
產品目錄頁面: 779 (CN2011-ZH PDF)
配用: EVAL-AD7767EDZ-ND - BOARD EVAL AD7767 128KSPS 108DB
EVAL-AD7767-1EDZ-ND - BOARD EVAL AD7767-1 64KSPS 111DB
AD7767
Rev. C | Page 22 of 2
4
VREF+ INPUT SIGNAL
The AD7767/AD7767-1/AD7767-2 VREF + pin is supplied with a
voltage in the range of 2.4 V to 2 × AVDD (nominally 5 V). It is
recommended that the VREF+ input be generated by a low noise
voltage reference. Examples of such references are the ADR445,
ADR435, ADR425 (5 V output), and ADR421 (2.5 V output).
Typical reference supply circuits are shown in Figure 46.
The reference voltage input pin (VREF+) also acts as a power
supply to the AD7767/AD7767-1/AD7767-2 device. For a 5 V
VREF+ input, a full-scale input of 5 V on both VIN+ and VIN can
be applied while voltage supplies to pins AVDD remain at 2.5 V.
This configuration reduces the number of different supplies
required.
The output of the low noise voltage reference does not require a
buffer; however, decoupling the output of the low noise reference is
important. Place a 0.1 μF capacitor at the output of the voltage
reference devices (ADR445, ADR435, ADR425, and ADR421)
and follow the decoupling advice provided for the reference
device chosen.
As mentioned, the nominal supply to the VREF+ pin is 5 V to
achieve the full dynamic range available. When a 2.5 V VREF+
input is used (that is, in low power applications), the signal-to-
noise ratio and dynamic range figures (generated using a 5 V
VREF+ input) quoted in the Specifications section decrease by
6 dB, a direct result of halving the available input range.
The AD7767/AD7767-1/AD7767-2 device requires a 100 μF
capacitor to ground, which acts as a decoupling capacitor and as
a reservoir of charge for the VREF+ pin. Place this capacitor as
close to the AD7767/AD7767-1/AD7767-2 device as possible.
Reducing the value of this capacitor (C40 in Figure 46) to 10 μF
typically degrades noise performance by 1 dB. C40 can be an
electrolytic or tantalum capacitor.
C40
100F
C39
0.1F
C35
0.1F
C34
10F
REFERENCE
SUPPLY
V+
VREF+
VOUT
VIN
06
85
9-
0
21
AD7767/
AD7767-1/
AD7767-2
ADR4xx
Figure 46. AD7767/AD7767-1/AD7767-2 Reference Input Configuration
MULTIPLEXING ANALOG INPUT CHANNELS
The AD7767/AD7767-1/AD7767-2 can be used with a multi-
plexer configuration. As per any converter that uses a digital
filtering block, the maximum switching rate or the output data
rate per channel is a function of the digital filter settling time.
A user multiplexing the analog inputs to a converter that
employs a digital filter must wait the full digital filter settling
time before a valid conversion result can be achieved; after this
settling time, the channel can be switched. Then, the full
settling time must again be observed before a valid conversion
result is available and the input is switched once more.
The AD7767 filter settling time equals 74 divided by the output
data rate in use. The maximum switching frequency in a
multiplexed application is, therefore, 1/(74/ODR), where the
output data rate (ODR) is a function of the applied MCLK
frequency and the decimation rate employed by the device in
question. For example, applying a 1.024 MHz MCLK frequency
to the AD7767 results in a maximum output data rate of 128 kHz,
which in turn allows a 1.729 kHz multiplexer switching rate.
The AD7767-1 and the AD7767-2 employ digital filters with
longer settling time to achieve greater precision; thus, the
maximum switching frequency for these devices is 864 Hz and
432 Hz, respectively.
相關PDF資料
PDF描述
AD7660ASTZ IC ADC 16BIT UNIPOLAR 48-LQFP
VE-J11-MW-F1 CONVERTER MOD DC/DC 12V 100W
LTC1403AIMSE#PBF IC ADC 14BIT 2.8MSPS 10-MSOP
AD7658BSTZ IC ADC 12BIT 6CH 250KSPS 64LQFP
AD7767BRUZ-1 ADC 24BIT 64KSPS SAR 16-TSSOP
相關代理商/技術參數
參數描述
AD7767BRUZ-1 功能描述:ADC 24BIT 64KSPS SAR 16-TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率(每秒):1M 數據接口:串行,SPI? 轉換器數目:1 功率耗散(最大):- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤(4x4) 包裝:Digi-Reel® 輸入數目和類型:8 個單端,單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6
AD7767BRUZ-1-RL7 功能描述:ADC 24BIT 10.5MW 64KSPS 16TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率(每秒):300k 數據接口:并聯 轉換器數目:1 功率耗散(最大):75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC(0.295",7.50mm 寬) 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端,單極;1 個單端,雙極
AD7767BRUZ-2 功能描述:ADC 24BIT 32KSPS SAR 16-TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 其它有關文件:TSA1204 View All Specifications 標準包裝:1 系列:- 位數:12 采樣率(每秒):20M 數據接口:并聯 轉換器數目:2 功率耗散(最大):155mW 電壓電源:模擬和數字 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-TQFP 供應商設備封裝:48-TQFP(7x7) 包裝:Digi-Reel® 輸入數目和類型:4 個單端,單極;2 個差分,單極 產品目錄頁面:1156 (CN2011-ZH PDF) 其它名稱:497-5435-6
AD7767BRUZ-2-RL7 功能描述:ADC 24BIT 8.5MW 32KSPS 16TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率(每秒):300k 數據接口:并聯 轉換器數目:1 功率耗散(最大):75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC(0.295",7.50mm 寬) 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端,單極;1 個單端,雙極
AD7767BRUZ-RL7 功能描述:ADC 24BIT 15MW 128KSPS 16TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率(每秒):300k 數據接口:并聯 轉換器數目:1 功率耗散(最大):75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC(0.295",7.50mm 寬) 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端,單極;1 個單端,雙極