參數資料
型號: AD7767BRUZ-1-RL7
廠商: Analog Devices Inc
文件頁數: 11/25頁
文件大?。?/td> 0K
描述: ADC 24BIT 10.5MW 64KSPS 16TSSOP
標準包裝: 1,000
位數: 24
采樣率(每秒): 64k
數據接口: 串行
轉換器數目: 1
功率耗散(最大): 18mW
電壓電源: 模擬和數字
工作溫度: -40°C ~ 105°C
安裝類型: 表面貼裝
封裝/外殼: 16-TSSOP(0.173",4.40mm 寬)
供應商設備封裝: 16-TSSOP
包裝: 帶卷 (TR)
輸入數目和類型: 1 個差分,單極
配用: EVAL-AD7767EDZ-ND - BOARD EVAL AD7767 128KSPS 108DB
EVAL-AD7767-1EDZ-ND - BOARD EVAL AD7767-1 64KSPS 111DB
AD7767
Rev. C | Page 18 of
24
DAISY CHAINING
Daisy chaining devices allows numerous devices to use the same
digital interface lines by cascading the outputs of multiple ADCs
on a single data line. This feature is especially useful for reduc-
ing component count and wiring connections, for example, in
isolated multiconverter applications or for systems with a limited
interfacing capacity. Data readback is analogous to clocking a
shift register where data is clocked on the falling edge of SCLK.
The block diagram in Figure 36 shows how devices must be
connected to achieve daisy-chain functionality. The scheme
shown operates by passing the output data of the SDO pin of an
AD7767 device to the SDI input of the next AD7767 device in
the chain. The data then continues through the chain until it is
clocked onto the SDO pin of the first device in the chain.
READING DATA IN DAISY-CHAIN MODE
An example of a daisy chain of four AD7767 devices is shown in
Figure 36 and Figure 37. In the case illustrated in Figure 36, the
output of the AD7767 labeled A is the output of the full daisy
chain. The last device in the chain (the AD7767 labeled D) has
its serial data input (SDI) pin connected to ground. All the
devices in the chain must use common MCLK, SCLK, CS, and
SYNC/PD signals.
To enable the daisy-chain conversion process, apply a common
SYNC/PD pulse to all devices, synchronizing all the devices in
the chain (see the
section).
After applying a SYNC/PD pulse to all the devices, there is a
delay (as listed in
) before valid conversion data appears
at the output of the chain of devices. As shown in
, the
first conversion result is output from the AD7767 device labeled
A. This 24-bit conversion result is followed by the conversion
results from the devices labeled B, C, and D, respectively, with
all conversion results output in an MSB-first sequence. The
stream of conversion results is clocked through each device in
the chain and is eventually clocked onto the SDO pin of the
AD7767 device labeled A. The conversion results of all the
devices in the chain must be clocked onto the SDO pin of the
final device in the chain while its
DRDY signal is active low.
This is illustrated in the examples shown (
and
),
where the conversion results from the devices labeled A, B, C,
and D are clocked onto SDO (A) during the time between the
falling edge of
DRDY (A) and the rising edge of DRDY (A).
CHOOSING THE SCLK FREQUENCY
As shown in Figure 37, the number of SCLK falling edges that
occur during the period when DRDY (A) is active low must
match the number of devices in the chain multiplied by 24 (the
number of bits that must be clocked through onto SDO (A) for
each device).
The period of SCLK (tSCLK) required for a known daisy-chain
length using a known common MCLK frequency must,
therefore, be established in advance. Note that the maximum
SCLK frequency is governed by t8 and is specified in the Timing
Specifications table for different VDRIVE voltages.
In the case where CS is tied logic low,
×
K
t
READ
SCLK
24
(1)
where:
K
is the number of AD7767 devices in the chain.
tSCLK
is the period of the SCLK.
tREAD
equals tDRDY t5.
In the case where CS is used in the daisy-chain interface,
(
) (
)
×
+
K
t
13
7
6
READ
SCLK
24
(2)
where:
K
is the number of AD7767 devices in the chain.
tSCLK
is the period of the SCLK.
tREAD
equals tDRDY t5.
Note that the maximum value of SCLK is governed by t8 and is
specified in the Timing Specifications table for different VDRIVE
voltages.
相關PDF資料
PDF描述
VI-23D-CU-F2 CONVERTER MOD DC/DC 85V 200W
AD7658BSTZ-REEL IC ADC 12BIT 6CH 250KSPS 64-LQFP
VI-23D-CU-F1 CONVERTER MOD DC/DC 85V 200W
VE-B2W-MW-F2 CONVERTER MOD DC/DC 5.5V 100W
VI-23B-IW-S CONVERTER MOD DC/DC 95V 100W
相關代理商/技術參數
參數描述
AD7767BRUZ-2 功能描述:ADC 24BIT 32KSPS SAR 16-TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 其它有關文件:TSA1204 View All Specifications 標準包裝:1 系列:- 位數:12 采樣率(每秒):20M 數據接口:并聯 轉換器數目:2 功率耗散(最大):155mW 電壓電源:模擬和數字 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-TQFP 供應商設備封裝:48-TQFP(7x7) 包裝:Digi-Reel® 輸入數目和類型:4 個單端,單極;2 個差分,單極 產品目錄頁面:1156 (CN2011-ZH PDF) 其它名稱:497-5435-6
AD7767BRUZ-2-RL7 功能描述:ADC 24BIT 8.5MW 32KSPS 16TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率(每秒):300k 數據接口:并聯 轉換器數目:1 功率耗散(最大):75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC(0.295",7.50mm 寬) 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端,單極;1 個單端,雙極
AD7767BRUZ-RL7 功能描述:ADC 24BIT 15MW 128KSPS 16TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率(每秒):300k 數據接口:并聯 轉換器數目:1 功率耗散(最大):75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC(0.295",7.50mm 寬) 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端,單極;1 個單端,雙極
AD7768-4BSTZ 功能描述:24 Bit Analog to Digital Converter 4 Input 4 Sigma-Delta 64-LQFP (10x10) 制造商:analog devices inc. 系列:- 包裝:托盤 零件狀態:有效 位數:24 采樣率(每秒):256k 輸入數:4 輸入類型:差分 數據接口:SPI 配置:ADC 無線電 - S/H:ADC:- A/D 轉換器數:4 架構:三角積分 參考類型:外部 電壓 - 電源,模擬:2 V ~ 5.5 V 電壓 - 電源,數字:- 特性:同步采樣 工作溫度:-40°C ~ 150°C 封裝/外殼:64-LQFP 供應商器件封裝:64-LQFP(10x10) 標準包裝:1
AD7768-4BSTZ-RL 功能描述:24 Bit Analog to Digital Converter 4 Input 4 Sigma-Delta 64-LQFP (10x10) 制造商:analog devices inc. 系列:- 包裝:帶卷(TR) 零件狀態:有效 位數:24 采樣率(每秒):256k 輸入數:4 輸入類型:差分 數據接口:SPI 配置:ADC 無線電 - S/H:ADC:- A/D 轉換器數:4 架構:三角積分 參考類型:外部 電壓 - 電源,模擬:2 V ~ 5.5 V 電壓 - 電源,數字:- 特性:同步采樣 工作溫度:-40°C ~ 150°C 封裝/外殼:64-LQFP 供應商器件封裝:64-LQFP(10x10) 標準包裝:1,500