- 您現在的位置：買賣IC網 > PDF目錄10289 > AD7707BRU-REEL7 (Analog Devices Inc)IC ADC 16BIT 3CH 20-TSSOP T/R PDF資料下載
參數資料
| 型號： | AD7707BRU-REEL7 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 10/52頁 |
| 文件大小： | 0K |
| 描述： | IC ADC 16BIT 3CH 20-TSSOP T/R |
| 標準包裝： | 1,000 |
| 位數： | 16 |
| 采樣率（每秒）： | 500 |
| 數據接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 1mW |
| 電壓電源： | 模擬和數字 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 20-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 20-TSSOP |
| 包裝： | 帶卷 (TR) |
| 輸入數目和類型： | 1 個單端，單極；1 個單端，雙極；2 個偽差分，單極；2 個偽差分，雙極 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁
AD7707
Rev. B | Page 18 of 52
ON-CHIP REGISTERS
The AD7707 contains eight on-chip registers that can be
accessed via the serial port of the part. The first of these is a
communications register that controls the channel selection,
decides whether the next operation is a read or write operation
and selects which register the next read or write operation
accesses. All communications to the part must start with a write
operation to the communications register. After power-on or
RESET, the device expects a write to its communications register.
The data written to this register determines whether the next
operation to the part is a read or a write operation and
determines to which register this read or write operation occurs.
Therefore, write access to any of the other registers on the part
starts with a write operation to the communications register
followed by a write to the selected register. A read operation
from any other register on the part (including the communications
register itself and the data register) starts with a write operation
to the communications register followed by a read operation
from the selected register. The communications register also
controls the standby mode and channel selection and the DRDY
status is available by reading from the communications register.
The second register is a setup register that determines calibration
mode, gain setting, bipolar/unipolar operation, and buffered
mode. The third register is the clock register and contains the
filter selection bits and clock control bits. The fourth register is
the data register from which the output data from the part is
accessed. The final registers are the calibration registers, which
store channel calibration data. The registers are described in
more detail in the following sections.
COMMUNICATIONS REGISTER (RS2, RS1, RS0 = 0,
0, 0)
The communications register is an 8-bit register from which
data can either be read or to which data can be written. All
communications to the part must start with a write operation to
the communications register. The data written to the commu-
nications register determines whether the next operation is a
read or write operation and to which register this operation
takes place. When the subsequent read or write operation to the
selected register is complete, the interface returns to where it
expects a write operation to the communications register. This
is the default state of the interface, and on power-up or after a
RESET, the AD7707 is in this default state waiting for a write
operation to the communications register. In situations where
the interface sequence is lost, if a write operation of sufficient
duration (containing at least 32 serial clock cycles) takes place
with DIN high, the AD7707 returns to this default state.
outlines the bit designations for the communications register.
Table 14. Communications Register
0/DRDY (0)
RS2 (0)
RS1 (0)
RS0 (0)
R/W (0)
STBY (0)
CH1 (0)
CH0 (0)
Table 15. Communications Register Bit Descriptions
Bit
Description
0/DRDY
For a write operation, a 0 must be written to this bit so that the write operation to the communications register actually takes place. If a
1 is written to this bit, the part does not clock on to subsequent bits in the register. The serial interface stays at this bit location
until a 0 is written to this bit. Once a 0 is written to this bit, the next seven bits are loaded to the communications register. For a read
operation, this bit provides the status of the DRDY flag from the part. The status of this bit is the same as the DRDY output pin.
RS2 to
RS0
Register selection bits. These three bits select to which one of eight on-chip registers the next read or write operation takes
place, as shown in Table 16, along with the register size. When the read or write operation to the selected register is complete,
the part waits for a write operation to the communications register. It does not remain in a state where it continues to access the
register.
R/W
Read/Write select. This bit selects whether the next operation is a read or write operation to the selected register. A 0 indicates a
write cycle for the next operation to the appropriate register, while a 1 indicates a read operation from the appropriate register.
STBY
Standby. Writing a 1 to this bit puts the part into its standby or power-down mode. In this mode, the part consumes only
8 μA of power supply current. The part retains its calibration coefficients and control word information when in standby. Writing
a 0 to this bit places the part in its normal operating mode. The serial interface on the AD7707 remains operational when the
part is in standby mode.
CH1,
CH0
Channel select. These two bits select a channel for conversion or for access to the calibration coefficients as outlined in Table 17.
Three pairs of calibration registers on the part are used to store the calibration coefficients following a calibration on a channel. They are
shown in Table 17 for the AD7707 to indicate which channel combinations have independent calibration coefficients. With CH1
at Logic 1 and CH0 at a Logic 0, the part looks at the LOCOM input internally shorted to itself. This can be used as a test method
to evaluate the noise performance of the part with no external noise sources. In this mode, the LOCOM input should be
connected to an external voltage within the allowable common-mode range for the part.
相關PDF資料 |
PDF描述 |
|---|---|
| MS27497T16B8PA | CONN RCPT 8POS WALL MNT W/PINS |
| D38999/24MF32BA | CONN HSG RCPT 32POS JAM NUT SCKT |
| MS27497E14A18P | CONN RCPT 18POS WALL MNT W/PINS |
| D38999/26JG39SALC | CONN HSG PLUG 39POS STRGHT SCKT |
| MS3106A20-19S | CONN PLUG 3POS STRAIGHT W/SCKT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7707BRUZ | 功能描述:IC ADC 16BIT 3CH 20-TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 其它有關文件:TSA1204 View All Specifications 標準包裝:1 系列:- 位數:12 采樣率（每秒）:20M 數據接口:并聯 轉換器數目:2 功率耗散（最大）:155mW 電壓電源:模擬和數字 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-TQFP 供應商設備封裝:48-TQFP（7x7） 包裝:Digi-Reel® 輸入數目和類型:4 個單端，單極；2 個差分，單極 產品目錄頁面:1156 (CN2011-ZH PDF) 其它名稱:497-5435-6 |
| AD7707BRUZ-REEL | 功能描述:IC ADC 16BIT 3CH 20-TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| AD7707BRUZ-REEL7 | 功能描述:IC ADC 16BIT 3CHAN 20TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| AD7707BRZ | 功能描述:IC ADC 16BIT 3CHAN 20SOIC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 其它有關文件:TSA1204 View All Specifications 標準包裝:1 系列:- 位數:12 采樣率（每秒）:20M 數據接口:并聯 轉換器數目:2 功率耗散（最大）:155mW 電壓電源:模擬和數字 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-TQFP 供應商設備封裝:48-TQFP（7x7） 包裝:Digi-Reel® 輸入數目和類型:4 個單端，單極；2 個差分，單極 產品目錄頁面:1156 (CN2011-ZH PDF) 其它名稱:497-5435-6 |
| AD7707BRZ-REEL | 功能描述:IC ADC 16BIT 3CHAN 20SOIC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
發布緊急采購，3分鐘左右您將得到回復。