- 您現在的位置：買賣IC網 > PDF目錄1982 > AD7689BCPZRL7 (Analog Devices Inc)IC ADC 16BIT 250KSPS 8CH 20LFCSP PDF資料下載
參數資料
| 型號： | AD7689BCPZRL7 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 15/32頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 16BIT 250KSPS 8CH 20LFCSP |
| 產品培訓模塊： | Power Line Monitoring Motor Control |
| 產品變化通告： | Startup Circuitry Design Improvement Change 15/April/2009 |
| 標準包裝： | 1 |
| 系列： | PulSAR® |
| 位數： | 16 |
| 采樣率（每秒）： | 250k |
| 數據接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 21mW |
| 電壓電源： | 模擬和數字 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 20-VFQFN 裸露焊盤，CSP |
| 供應商設備封裝： | 20-LFCSP-VQ |
| 包裝： | 標準包裝 |
| 輸入數目和類型： | 8 個單端，單極；4 個差分，雙極；4 個偽差分，雙極 |
| 其它名稱： | AD7689BCPZRL7DKR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
AD7682/AD7689
Data Sheet
Rev. D | Page 22 of 32
External Reference and Internal Buffer
For improved drift performance, an external reference can be
used with the internal buffer, as shown in Figure 32. The
external source is connected to REFIN, the input to the on-chip
unity gain buffer, and the output is produced on the REF pin.
An external reference can be used with the internal buffer with
or without the temperature sensor enabled. Refer to Table 10 for
register details. With the buffer enabled, the gain is unity and
is limited to an input/output of VDD = 0.2 V; however, the
maximum voltage allowable must be ≤(VDD 0.5 V).
The internal reference buffer is useful in multiconverter appli-
cations because a buffer is typically required in these applications.
In addition, a low power reference can be used because the
internal buffer provides the necessary performance to drive the
REF
GND
TEMP
AD7682/
AD7689
10F
100nF
REFIN
REF SOURCE
≤ (VDD – 0.5V)
Figure 32. External Reference Using Internal Buffer
External Reference
In any of the six voltage reference schemes, an external reference
can be connected directly on the REF pin as shown in Figure 33
because the output impedance of REF is >5 kΩ. To reduce power
consumption, the reference and buffer should be powered down.
Refer to Table 10 for register details. For improved drift
performance, an external reference such as the ADR43x or
ADR44x is recommended.
REF
GND
TEMP
10F
REFIN
REF SOURCE
0.5V < REF < (VDD + 0.3V)
NO CONNECTION
REQUIRED
07
35
3-
0
47
AD7682/
AD7689
Figure 33.External Reference
Note that the best SNR is achieved with a 5 V external reference
as the internal reference is limited to 4.096 V. The SNR
degradation is as follows:
5
096
.
4
log
20
=
LOSS
SNR
Reference Decoupling
Whether using an internal or external reference, the AD7682/
AD7689 voltage reference output/input, REF, has a dynamic
input impedance and should therefore be driven by a low
impedance source with efficient decoupling between the REF
and GND pins. This decoupling depends on the choice of the
voltage reference but usually consists of a low ESR capacitor
connected to REF and GND with minimum parasitic inductance.
A 10 μF (X5R, 1206 size) ceramic chip capacitor is appropriate
external reference, or a low impedance buffer such as the
The placement of the reference decoupling capacitor is also impor-
the Layout section. Mount the decoupling capacitor on the same
side as the ADC at the REF pin with a thick PCB trace. The GND
should also connect to the reference decoupling capacitor with
the shortest distance and to the analog ground plane with
several vias.
If desired, smaller reference decoupling capacitor values down
to 2.2 μF can be used with a minimal impact on performance,
especially on DNL.
Regardless, there is no need for an additional lower value ceramic
decoupling capacitor (for example, 100 nF) between the REF
and GND pins.
other PulSAR devices, it is more effective to use the internal
reference buffer to buffer the external reference voltage, thus
reducing SAR conversion crosstalk.
The voltage reference temperature coefficient (TC) directly
impacts full scale; therefore, in applications where full-scale
accuracy matters, care must be taken with the TC. For instance,
a ±10 ppm/°C TC of the reference changes full scale by ±1 LSB/°C.
相關PDF資料 |
PDF描述 |
|---|---|
| AD7690BCPZRL | IC ADC 18BIT 400KSPS 10-LFCSP |
| AD7691BCPZRL7 | IC ADC 18BIT SAR 250KSPS 10LFCSP |
| AD7693BRMZRL7 | IC ADC 16BIT 500KSPS 10-MSOP |
| AD7694ARMZ | IC ADC 16BIT SAR 250KSPS 8MSOP |
| AD7699BCPZRL7 | IC ADC 8CH 16BIT 500KSPS 20LFCSP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD768ACHIPS | 制造商:AD 制造商全稱:Analog Devices 功能描述:16-Bit, 30 MSPS D/A Converter |
| AD768AF/QMLR | 制造商:Analog Devices 功能描述: |
| AD768AR | 功能描述:IC DAC 16BIT 30MSPS 28-SOIC RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1,000 系列:- 設置時間:1µs 位數:8 數據接口:串行 轉換器數目:8 電壓電源:雙 ± 功率耗散（最大）:941mW 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC W 包裝:帶卷 (TR) 輸出數目和類型:8 電壓，單極 采樣率（每秒）:* |
發布緊急采購，3分鐘左右您將得到回復。