參數資料
型號: AD7687BCPZRL7
廠商: Analog Devices Inc
文件頁數: 17/28頁
文件大?。?/td> 0K
描述: IC ADC 16BIT SAR 250KSPS 10LFCSP
標準包裝: 1
系列: PulSAR®
位數: 16
采樣率(每秒): 250k
數據接口: DSP,MICROWIRE?,QSPI?,串行,SPI?
轉換器數目: 1
功率耗散(最大): 12.5mW
電壓電源: 模擬和數字
工作溫度: -40°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: 10-WFDFN 裸露焊盤,CSP
供應商設備封裝: 10-LFCSP-WD(3x3)
包裝: 標準包裝
輸入數目和類型: 1 個差分,雙極
產品目錄頁面: 778 (CN2011-ZH PDF)
配用: EVAL-AD7687CBZ-ND - BOARD EVALUATION FOR AD7687
其它名稱: AD7687BCPZRL7DKR
AD7687
Data Sheet
Rev. B | Page 24 of 28
APPLICATION HINTS
LAYOUT
The printed circuit board that houses the AD7687 should be
designed so that the analog and digital sections are separated
and confined to certain areas of the board. The pinout of the
AD7687, with all its analog signals on the left side and all its
digital signals on the right side, eases this task.
Avoid running digital lines under the device because these
couple noise onto the die, unless a ground plane under the
AD7687 is used as a shield. Fast switching signals, such as CNV
or clocks, should never run near analog signal paths. Crossover
of digital and analog signals should be avoided
At least one ground plane should be used. It could be common
or split between the digital and analog sections. In the latter
case, the planes should be joined underneath the AD7687s.
The AD7687 voltage reference input REF has a dynamic input
impedance and should be decoupled with minimal parasitic
inductances. This is done by placing the reference decoupling
ceramic capacitor close to, and ideally right up against, the REF
and GND pins and connecting it with wide, low impedance
traces.
Finally, the power supplies VDD and VIO of the AD7687
should be decoupled with ceramic capacitors (typically 100 nF)
placed close to the AD7687 and connected using short and wide
traces to provide low impedance paths and reduce the effect of
glitches on the power supply lines.
An example of layout following these rules is shown in
EVALUATING THE AD7687’S PERFORMANCE
Other recommended layouts for the AD7687 are outlined
in the documentation of the evaluation board for the AD7687
(EVAL-AD7687). The evaluation board package includes
a fully assembled and tested evaluation board, documentation,
and software for controlling the board from a PC via the
EVAL-CONTROL BRD3.
02972-046
Figure 47. Example of Layout of the AD7687 (Top Layer)
02972-047
Figure 48. Example of Layout of the AD7687 (Bottom Layer)
相關PDF資料
PDF描述
LTC2847IUHF#PBF IC TXRX MULTIPROTOCOL 38-QFN
1445818-3 CONN PLUG HOUSING 11-7POS CPC
MAX1249BEEE+ IC ADC 10BIT SERIAL 16-QSOP
1445820-1 CONN PLUG HOUSING 11-5POS CPC
1445819-1 CONN PLUG HOUSING 11-6POS CPC
相關代理商/技術參數
參數描述
AD7687BRM 制造商:Analog Devices 功能描述:ADC Single SAR 250ksps 16-bit Serial 10-Pin MSOP Tube 制造商:Analog Devices 功能描述:IC 16-BIT ADC
AD7687BRMRL7 制造商:Analog Devices 功能描述:ADC Single SAR 250ksps 16-bit Serial 10-Pin MSOP T/R
AD7687BRMZ 功能描述:IC ADC 16BIT 250KSPS 10-MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:PulSAR® 標準包裝:1 系列:microPOWER™ 位數:8 采樣率(每秒):1M 數據接口:串行,SPI? 轉換器數目:1 功率耗散(最大):- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤(4x4) 包裝:Digi-Reel® 輸入數目和類型:8 個單端,單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6
AD7687BRMZRL7 功能描述:IC ADC 16BIT 250KSPS 10MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:PulSAR® 標準包裝:1,000 系列:- 位數:12 采樣率(每秒):300k 數據接口:并聯 轉換器數目:1 功率耗散(最大):75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC(0.295",7.50mm 寬) 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端,單極;1 個單端,雙極
AD7688 制造商:AD 制造商全稱:Analog Devices 功能描述:16-Bit, +/-0.65 LSB INL, 500 kSPS PulSAR Differential ADC in MSOP/QFN