- 您現在的位置：買賣IC網 > PDF目錄10674 > AD7682BCPZ (Analog Devices Inc)IC ADC 16BIT 4CH 250KSPS 20LFCSP PDF資料下載
參數資料
| 型號： | AD7682BCPZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 11/32頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 16BIT 4CH 250KSPS 20LFCSP |
| 產品培訓模塊： | Power Line Monitoring |
| 產品變化通告： | Startup Circuitry Design Improvement Change 15/April/2009 |
| 標準包裝： | 1 |
| 系列： | PulSAR® |
| 位數： | 16 |
| 采樣率（每秒）： | 250k |
| 數據接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 21mW |
| 電壓電源： | 模擬和數字 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 20-VFQFN 裸露焊盤，CSP |
| 供應商設備封裝： | 20-LFCSP-VQ |
| 包裝： | 托盤 |
| 輸入數目和類型： | 8 個單端，單極；4 個差分，雙極；4 個偽差分，雙極 |
| 產品目錄頁面： | 778 (CN2011-ZH PDF) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
Data Sheet
AD7682/AD7689
Rev. D | Page 19 of 32
Unipolar or Bipolar
Figure 26 shows an example of the recommended connection
available.
Bipolar Single Supply
Figure 27 shows an example of a system with a bipolar input
using single supplies with the internal reference (optional
different VIO supply). This circuit is also useful when the
amplifier/signal conditioning circuit is remotely located with
some common mode present. Note that for any input config-
uration, the INx inputs are unipolar and are always referenced
to GND (no negative voltages even in bipolar range).
For this circuit, a rail-to-rail input/output amplifier can be used;
however, the offset voltage vs. input common-mode range should
be noted and taken into consideration (1 LSB = 62.5 μV with
VREF = 4.096 V). Note that the conversion results are in twos
complement format when using the bipolar input configuration.
Refer to the AN-581 Application Note, Biasing and Decoupling
Op Amps in Single Supply Applications, for additional details
about using single-supply amplifiers.
ANALOG INPUTS
Input Structure
Figure 28 shows an equivalent circuit of the input structure of
protection for the analog inputs, IN[7:0] and COM. Care must
be taken to ensure that the analog input signal does not exceed
the supply rails by more than 0.3 V because this causes the
diodes to become forward biased and to start conducting
current.
These diodes can handle a forward-biased current of 130 mA
maximum. For instance, these conditions may eventually occur
when the input buffer supplies are different from VDD. In such
a case, for example, an input buffer with a short circuit, the
current limitation can be used to protect the part.
CIN
RIN
D1
D2
CPIN
INx+
OR INx–
OR COM
GND
VDD
07
35
3-
0
3
0
Figure 28. Equivalent Analog Input Circuit
This analog input structure allows the sampling of the true
differential signal between INx+ and COM or INx+ and INx.
(COM or INx = GND ± 0.1 V or VREF ± 0.1 V). By using these
differential inputs, signals common to both inputs are rejected,
as shown in Figure 29.
70
65
60
55
50
45
40
35
30
1
10k
10
CM
RR
(
d
B)
100
1k
FREQUENCY (kHz)
07
35
3-
03
1
Figure 29. Analog Input CMRR vs. Frequency
During the acquisition phase, the impedance of the analog inputs
can be modeled as a parallel combination of the capacitor, CPIN,
and the network formed by the series connection of RIN and CIN.
CPIN is primarily the pin capacitance. RIN is typically 2.2 kΩ and
is a lumped component composed of serial resistors and the on
resistance of the switches. CIN is typically 27 pF and is mainly
the ADC sampling capacitor.
Selectable Low-Pass Filter
During the conversion phase, where the switches are opened,
filter that reduces undesirable aliasing effects and limits the
noise from the driving circuitry. The low-pass filter can be pro-
grammed for the full bandwidth or of the bandwidth with
Note that the converter throughput must also be reduced by
when using the filter. If the maximum throughput is used with the
bandwidth (BW) set to , the converter acquisition time, tACQ, is
violated, resulting in increased THD.
相關PDF資料 |
PDF描述 |
|---|---|
| AD7794BRUZ | IC ADC 24BIT SIG-DEL 6CH 24TSSOP |
| AD7689ACPZ | IC ADC 16BIT 250KSPS 8CH 20LFCSP |
| LTC1598CG#PBF | IC A/D CONV 12BIT SRL 8CH 24SSOP |
| KA339A | IC COMPARATOR QUAD 14-DIP |
| KA339 | IC COMPARATOR QUAD 14-DIP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7682BCPZRL7 | 功能描述:IC ADC 16BIT 4CH 250KSPS 20LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:PulSAR® 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| AD7683 | 制造商:AD 制造商全稱:Analog Devices 功能描述:16-Bit, 100 kSPS PulSAR ADC in MSOP/QFN |
| AD7683ACPZRL | 功能描述:IC ADC 16BIT SRL 100KSPS 8LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:PulSAR® 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| AD7683ACPZRL7 | 功能描述:IC ADC 16BIT 100KSPS 8LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:PulSAR® 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| AD7683ARM | 制造商:Analog Devices 功能描述:ADC Single SAR 100ksps 16-bit Serial 8-Pin MSOP Tube |
發布緊急采購，3分鐘左右您將得到回復。