參數資料
型號: AD7669JP
廠商: Analog Devices Inc
文件頁數: 3/20頁
文件大?。?/td> 0K
描述: IC I/O PORT 8BIT ANLG 28-PLCC
產品變化通告: Product Discontinuance 27/Oct/2011
標準包裝: 1
系列: LC²MOS
應用: 模擬 I/O
接口: 總線
電源電壓: 4.75 V ~ 5.25 V
封裝/外殼: 28-LCC(J 形引線)
供應商設備封裝: 28-PLCC(11.51x11.51)
包裝: 管件
安裝類型: 表面貼裝
AD7569/AD7669
–11–
REV. B
RESET
line, the DAC output resets to 0 V when the entire
system is reset. Figure 7 shows the input control logic for the
AD7569 DAC; the write cycle timing diagram is shown in
Figure 8.
Figure 7. AD7569 DAC Input Control Logic
Figure 8. AD7569/AD7669 Write Cycle Timing Diagram
DAC Timing and Control—AD7669
Table III shows the truth table for the dual DAC operation of
the AD7669. The part contains two 8-bit DAC registers that are
loaded from the data bus under the control of CS, A/B and WR.
Address line A/B selects which DAC register the data is
loaded to. The data contained in the DAC registers determines
the analog output from the respective DACs. The WR input is
an edge-triggered input, and data is transferred into the selected
DAC register on the rising edge of WR. Holding CS and WR
low does not make the selected DAC register transparent. The
A
/B input should not be changed while CS and WR are low.
Table III. AD7669 DAC Truth Table
CS
WR
A
/B
RESET
DAC Function
H
X
H
DAC Registers Unaffected
L
g
L
H
DACA Register Updated
g
L
H
DACA Register Updated
L
g
H
DACB Register Updated
g
L
H
DACB Register Updated
X
L
DAC Registers Loaded with
All Zeros
L = Low State, H = High State, X = Don’t Care
The contents of the DAC registers are reset to all 0s by an active
low pulse on the RESET line, and for the unipolar output
ranges, the outputs remain at 0 V after RESET returns high.
For the bipolar output ranges, a low pulse on RESET causes the
outputs to go to negative full scale. In unipolar applications, the
RESET
line can be used to ensure power-up to 0 V on the
AD7669 DAC outputs and is also useful when used as a zero
override in system calibration cycles. If the RESET input is con-
nected to the system RESET line, then the DAC outputs reset
to 0 V when the entire system is reset. Figure 9 shows the DAC
input control logic for the AD7669, and the write cycle timing
diagram is shown in Figure 8.
Figure 9. AD7669 DAC Control Logic
ADC Timing and Control
The ADC on the AD7569/AD7669 is capable of two basic oper-
ating modes. In the first mode, the ST line is used to start con-
version and drive the track-and-hold into hold mode. At the end
of conversion, the track-and-hold returns to its tracking mode.
The second mode is achieved by hard-wiring the ST line high.
In this case, CS and RD start conversion, and the microproces-
sor is driven into a WAIT state for the duration of conversion by
BUSY
.
Figure 10. ADC Mode 1 Interface Timing
相關PDF資料
PDF描述
MS27467P19F35S CONN PLUG 66POS STRAIGHT W/SCKT
AD7569JN IC I/O PORT 8BIT ANLG 24-DIP
MS27468E23B53P CONN RCPT 53POS JAM NUT W/PINS
131-9403-021 CONN SMB PLUG CABLE STR RG-316
D38999/20WJ61PC CONN RCPT 61POS WALL MNT W/PINS
相關代理商/技術參數
參數描述
AD7669JP-REEL 制造商:Analog Devices 功能描述:Data Acquisition System Single ADC Dual DAC 8-Bit 28-Pin PLCC T/R 制造商:Rochester Electronics LLC 功能描述:COMPLETE 8-BIT I/0 SYSTEM - Tape and Reel
AD7669JPZ 功能描述:IC I/O PORT 8BIT ANLG 28-PLCC RoHS:是 類別:集成電路 (IC) >> 接口 - 專用 系列:LC²MOS 特色產品:NXP - I2C Interface 標準包裝:1 系列:- 應用:2 通道 I²C 多路復用器 接口:I²C,SM 總線 電源電壓:2.3 V ~ 5.5 V 封裝/外殼:16-TSSOP(0.173",4.40mm 寬) 供應商設備封裝:16-TSSOP 包裝:剪切帶 (CT) 安裝類型:表面貼裝 產品目錄頁面:825 (CN2011-ZH PDF) 其它名稱:568-1854-1
AD7669JR 制造商:Analog Devices 功能描述:Data Acquisition System Single ADC Dual DAC 8-Bit 28-Pin SOIC W 制造商:Rochester Electronics LLC 功能描述:COMPLETE 8-BIT 1/O SYSTEM - Bulk
AD7669JR-REEL 制造商:Rochester Electronics LLC 功能描述:- Tape and Reel
AD7669JRZ 功能描述:IC I/O PORT 8BIT ANLG 28SOIC RoHS:是 類別:集成電路 (IC) >> 接口 - 專用 系列:LC²MOS 特色產品:NXP - I2C Interface 標準包裝:1 系列:- 應用:2 通道 I²C 多路復用器 接口:I²C,SM 總線 電源電壓:2.3 V ~ 5.5 V 封裝/外殼:16-TSSOP(0.173",4.40mm 寬) 供應商設備封裝:16-TSSOP 包裝:剪切帶 (CT) 安裝類型:表面貼裝 產品目錄頁面:825 (CN2011-ZH PDF) 其它名稱:568-1854-1