- 您現在的位置：買賣IC網 > PDF目錄1980 > AD7327BRUZ-REEL7 (Analog Devices Inc)IC ADC 12BIT+ SAR 8CHAN 20TSSOP PDF資料下載
參數資料
| 型號： | AD7327BRUZ-REEL7 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 21/37頁 |
| 文件大小： | 0K |
| 描述： | IC ADC 12BIT+ SAR 8CHAN 20TSSOP |
| 標準包裝： | 1,000 |
| 位數： | 12 |
| 采樣率（每秒）： | 500k |
| 數據接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 17mW |
| 電壓電源： | 雙 ± |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 20-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 20-TSSOP |
| 包裝： | 帶卷 (TR) |
| 輸入數目和類型： | 8 個單端，單極；8 個單端，雙極；4 個差分，單極；4 個差分，雙極 |
| 配用： | EVAL-AD7327CBZ-ND - BOARD EVALUATION FOR AD7327 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁當前第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁
Data Sheet
AD7327
Rev. B | Page 27 of 36
REFERENCE
The AD7327 can operate with either the internal 2.5 V on-
chip reference or an externally applied reference. The internal
reference is selected by setting the Ref bit in the control register
to 1. On power-up, the Ref bit is 0, which selects the external
reference for the AD7327 conversion. Suitable reference sources
The internal reference circuitry consists of a 2.5 V band gap
reference and a reference buffer. When operating the AD7327
in internal reference mode, the 2.5 V internal reference is available
at the REFIN/OUT pin, which should be decoupled to AGND
using a 680 nF capacitor. It is recommended that the internal
reference be buffered before applying it elsewhere in the system.
The internal reference is capable of sourcing up to 90 μA.
On power-up, if the internal reference operation is required for
the ADC conversion, a write to the control register is necessary
to set the Ref bit to 1. During the control register write, the
conversion result from the first initial conversion is invalid. The
reference buffer requires 500 μs to power up and charge the
680 nF decoupling capacitor during the power-up time.
The AD7327 is specified for a 2.5 V to 3 V reference range.
When a 3 V reference is selected, the ranges are ±12 V, ±6 V,
±3 V, and 0 V to +12 V. For these ranges, the VDD and VSS supply
must be equal to or greater than the maximum analog input
range selected (see Table 6).
VDRIVE
the serial interface operates. VDRIVE allows the ADC to easily
interface to both 3 V and 5 V processors. For example, if the
powered from a 3 V supply. This allows the AD7327 to accept
large bipolar input signals with low voltage digital processing.
TEMPERATURE INDICATOR
The AD7327 has an on-chip temperature indicator. The
temperature indicator can be used to give local temperature
measurements on the AD7327. To access the temperature
indicator, the ADC should be configured in pseudo differential
mode, Mode 1 = Mode 0 = 1, and channel Bit ADD2, Bit ADD1,
and Bit ADD0 should be set to 1. VIN7 must be tied to AGND or
to a small dc voltage within the specified pseudo input range for
the selected analog input range. When a conversion is initiated
in this configuration, the output code represents the temperature
(see Figure 46 and Figure 47). When using the temperature
indicator on the AD7327, the part should be operated at low
throughput rates, such as approximately 50 kSPS for the ±10 V
range and 30 kSPS for the ±2.5 V range. The throughput rate is
reduced for the temperature indicator mode because the AD7327
requires more acquisition time for this mode.
4420
4340
–40
100
TEMPERATURE (°C)
AD
C
O
UT
P
U
T
CO
DE
4410
4400
4390
4380
4370
4360
4350
–20
0
20
40
60
80
±10V RANGE, INT REF
VCC =VDRIVE =5V
VDD/VSS = ±12V
50kSPS
0
5401-
033
Figure 46. Temperature vs. ADC Output Code for ±10 V Range
5450
5100
–40
80
TEMPERATURE (°C)
AD
C
O
UT
P
U
T
CO
DE
5400
5350
5300
5250
5200
5150
–20
0
20
40
60
VCC =VDRIVE =5V
VDD/VSS =±12V
±2.5V RANGE
INT REFERENCE
30kSPS
0
5401-
034
Figure 47. Temperature vs. ADC Output Code for ±2.5 V Range
相關PDF資料 |
PDF描述 |
|---|---|
| AD7328BRUZ-REEL | IC ADC 12BIT+SAR 8CHAN 20-TSSOP |
| AD7329BRUZ-REEL7 | IC ADC 12BIT+SAR 8CHAN 24-TSSOP |
| AD73311ARSZ | IC ANALOG FRONT END 20-SSOP |
| AD73322LARUZ-REEL | IC PROCESSOR FRONTEND DL 28TSSOP |
| AD73322LYRZ | IC ANALOG FRONT END DUAL 28-SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7328 | 制造商:AD 制造商全稱:Analog Devices 功能描述:8-Channel, Software-Selectable True Bipolar Input, 12-Bit Plus Sign ADC |
| AD7328BRUZ | 功能描述:IC ADC 12BIT+ SAR 8CHAN 20TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:iCMOS® 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
| AD7328BRUZ | 制造商:Analog Devices 功能描述:A/D Converter (A-D) IC |
| AD7328BRUZ-REEL | 功能描述:IC ADC 12BIT+SAR 8CHAN 20-TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:iCMOS® 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| AD7328BRUZ-REEL7 | 功能描述:IC ADC 12BIT+ SAR 8CHAN 20TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:iCMOS® 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
發布緊急采購，3分鐘左右您將得到回復。