- 您現在的位置：買賣IC網 > PDF目錄97841 > ACPM-5005-TR1 815 MHz - 849 MHz RF/MICROWAVE NARROW BAND MEDIUM POWER AMPLIFIER PDF資料下載
參數資料
| 型號： | ACPM-5005-TR1 |
| 元件分類： | 放大器 |
| 英文描述： | 815 MHz - 849 MHz RF/MICROWAVE NARROW BAND MEDIUM POWER AMPLIFIER |
| 封裝： | 3 X 3 MM, GREEN, PLASTIC, SMT, 10 PIN |
| 文件頁數： | 4/13頁 |
| 文件大小： | 303K |
| 代理商： | ACPM-5005-TR1 |
12
Storage Condition
Packages described in this document must be stored
in sealed moisture barrier, antistatic bags. Shelf life in a
sealed moisture barrier bag is 12 months at <40°C and
90% relative humidity (RH) J-STD-033 p.7.
Out-of-Bag Time Duration
After unpacking the device must be soldered to the PCB
within 168 hours as listed in the J-STD-020B p.11 with
factory conditions <30°C and 60% RH.
Baking
It is not necessary to re-bake the part if both conditions
(storage conditions and out-of bag conditions) have been
satisfied. Baking must be done if at least one of the con-
ditions above have not been satisfied. The baking condi-
tions are 125°C for 12 hours J-STD-033 p.8.
CAUTION
Tape and reel materials typically cannot be baked at the
temperature described above. If out-of-bag exposure
time is exceeded, parts must be baked for a longer time
at low temperatures, or the parts must be de-reeled,
de-taped, re-baked and then put back on tape and reel.
(See moisture sensitive warning label on each shipping
bag for information of baking).
Board Rework
Component Removal, Rework and Remount
If a component is to be removed from the board, it is
recommended that localized heating be used and the
maximum body temperatures of any surface mount
component on the board not exceed 200°C. This method
will minimize moisture related component damage. If any
component temperature exceeds 200°C, the board must
be baked dry per 4-2 prior to rework and/or component
removal. Component temperatures shall be measured at
the top center of the package body. Any SMD packages
that have not exceeded their floor life can be exposed to
a maximum body temperature as high as their specified
maximum reflow temperature.
Removal for Failure Analysis
Not following the above requirements may cause
moisture/reflow damage that could hinder or com-
damage that could hinder or com-
com-
pletely prevent the determination of the original failure
mechanism.
Baking of Populated Boards
Some SMD packages and board materials are not able to
withstand long duration bakes at 125°C. Examples of this
are some FR-4 materials, which cannot withstand a 24 hr
bake at 125°C. Batteries and electrolytic capacitors are
also temperature sensitive. With component and board
temperature restrictions in mind, choose a bake tem-
perature from Table 4-1 in J-STD 033; then determine the
appropriate bake duration based on the component to be
removed. For additional considerations see IPC-7711 and
IPC-7721.
Derating due to Factory Environmental Conditions
Factory floor life exposures for SMD packages removed
from the dry bags will be a function of the ambient envi-
ronmental conditions. A safe, yet conservative, handling
approach is to expose the SMD packages only up to the
maximum time limits for each moisture sensitivity level
as shown in next table. This approach, however, does not
work if the factory humidity or temperature is greater
than the testing conditions of 30°C/60% RH. A solution
for addressing this problem is to derate the exposure
times based on the knowledge of moisture diffusion in
the component package materials ref. JESD22-A120).
Recommended equivalent total floor life exposures can
be estimated for a range of humidities and temperatures
based on the nominal plastic thickness for each device.
Table on next page lists equivalent derated floor lives for
humidities ranging from 20-90% RH for three tempera-
ture, 20°C, 25°C, and 30°C.
Table on next page is applicable to SMDs molded
with novolac, biphenyl or multifunctional epoxy mold
compounds. The following assumptions were used in cal-
culating this table:
1. Activation Energy for diffusion = 0.35eV (smallest
known value).
2. For ≤60% RH, use Diffusivity = 0.121exp ( -0.35eV/kT)
mm2/s (this used smallest known Diffusivity @ 30°C).
3. For >60% RH, use Diffusivity = 1.320exp ( -0.35eV/kT)
mm2/s (this used largest known Diffusivity @ 30°C).
相關PDF資料 |
PDF描述 |
|---|---|
| ACPM-5013-BLK | 777 MHz - 798 MHz RF/MICROWAVE NARROW BAND MEDIUM POWER AMPLIFIER |
| ACPM-5013-TR1 | 777 MHz - 798 MHz RF/MICROWAVE NARROW BAND MEDIUM POWER AMPLIFIER |
| ACPM-5205-TR1 | 824 MHz - 849 MHz RF/MICROWAVE NARROW BAND LOW POWER AMPLIFIER |
| ACPM-5208-BLK | 880 MHz - 915 MHz RF/MICROWAVE NARROW BAND LOW POWER AMPLIFIER |
| ACPM-7311-BLKR | 824 MHz - 849 MHz RF/MICROWAVE NARROW BAND LOW POWER AMPLIFIER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ACPM-5007 | 制造商:AVAGO 制造商全稱:AVAGO TECHNOLOGIES LIMITED 功能描述:LTE Band7 (2500-2570 MHz) 3 x 3 mm Power Amplifi er Module |
| ACPM-5007-BLK | 制造商:Avago Technologies 功能描述:PA MODULE LTE BAND7 WITH CPL 3X3MM - Bulk |
| ACPM-5007-TR1 | 制造商:Avago Technologies 功能描述: 制造商:Avago Technologies 功能描述:3X3MM PAM, UMTS BAND 13 WITH CPL |
| ACPM-5008-BLK | 制造商:Avago Technologies 功能描述:3X3MM PAM, UMTS BAND8 WITH CPL - Rail/Tube |
| ACPM-5008-SC2 | 功能描述:RF Amplifier IC UMTS 880MHz ~ 915MHz 10-SMD 制造商:broadcom limited 系列:- 包裝:散裝 零件狀態:過期 頻率:880MHz ~ 915MHz P1dB:- 增益:28dB 噪聲系數:- RF 類型:UMTS 電壓 - 電源:3.2 V ~ 4.2 V 電流 - 電源:520mA 測試頻率:915MHz 封裝/外殼:10-SMD 模塊 供應商器件封裝:10-SMD 標準包裝:1 |
發布緊急采購，3分鐘左右您將得到回復。