- 您現在的位置：買賣IC網 > PDF目錄375225 > AC25B1FL MOSFET Transistor Power Dissipation:30W; Continuous Drain Current, Id:50uA; On-Resistance, Rds(on):0.015Ohm; Package/Case:TO-220; Drain Source Voltage, Vds:60V; Mounting Type:Through Hole PDF資料下載
參數資料
| 型號： | AC25B1FL |
| 英文描述： | MOSFET Transistor Power Dissipation:30W; Continuous Drain Current, Id:50uA; On-Resistance, Rds(on):0.015Ohm; Package/Case:TO-220; Drain Source Voltage, Vds:60V; Mounting Type:Through Hole |
| 中文描述： | 晶閘管產品目錄 |
| 文件頁數： | 156/224頁 |
| 文件大?。?/td> | 2697K |
| 代理商： | AC25B1FL |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁當前第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁第200頁第201頁第202頁第203頁第204頁第205頁第206頁第207頁第208頁第209頁第210頁第211頁第212頁第213頁第214頁第215頁第216頁第217頁第218頁第219頁第220頁第221頁第222頁第223頁第224頁
AN1006
Application Notes
http://www.teccor.com
+1 972-580-7777
AN1006 - 4
2002 Teccor Electronics
Thyristor Product Catalog
Power Rectifiers
The rectifier is a unidirectional device which conducts when for-
ward voltage (above 0.7 V) is applied.
To connect the rectifier:
1. Connect
Anode
to
Collector Terminal (C)
.
2. Connect
Cathode
to
Emitter Terminal (E)
.
To begin testing, perform the following procedures.
Procedure 1: V
RRM
and I
RM
To measure the V
RRM
and I
RM
parameter:
1. Set
Variable Collector Supply Voltage Range
to
1500 V.
(
2000 V
on 370)
2. Set
Horizontal
knob to sufficient scale to allow viewing of
trace at the required voltage level (
100 V/DIV
for 400 V and
600 V devices and
50 V/DIV
for 200 V devices).
3. Set
Mode
to
Leakage.
4. Set
Vertical
knob to
100 μA/DIV.
(Due to leakage setting, the
CRT readout will be 100 nA per division.)
5. Set
Terminal Selector
to
Emitter Grounded-Open Base.
6. Set
Polarity
to (–).
7. Set
Power Dissipation
to
2.2 W.
(
2 W
on 370)
8. Set
Left-Right Terminal Jack Selector
to correspond with
location of test fixture.
9. Increase
Variable Collector Supply Voltage
to the rated
V
RRM
of the device and observe the dot on the CRT. Read
across horizontally from the dot to the vertical current scale.
This measured value is the leakage current.
(Figure AN1006.2)
Figure AN1006.2
I
RM
= 340 nA at V
RRM
= 600 V
Procedure 2: V
FM
Before testing, note the following:
A Kelvin test fixture is required for this test. If a Kelvin fixture is
not used, an error in measurement of VFM will result due to
voltage drop in fixture. If a Kelvin fixture is not available,
Figure AN1006.3 shows necessary information to wire a test
fixture with Kelvin connections.
Due to the current limitations of standard curve tracer
model 576, V
FM
cannot be tested at rated current without a Tek-
tronix model 176 high-current module. The procedure below is
done at I
T(RMS)
= 10 A (20 A
PK
). This test parameter allows the
use of a standard curve tracer and still provides an estimate of
whether V
FM
is within specification.
Figure AN1006.3
Instructions for Wiring Kelvin Socket
To measure the V
FM
parameter:
1. Set
Variable Collector Supply Voltage Range
to
15 Max
Peak Volts
. (
16 V
on 370)
2. Set
Horizontal
knob to
0.5 V/DIV
.
3. Set
Mode
to
Norm
.
4. Set
Vertical
knob to
2 A/DIV
.
5. Set
Power Dissipation
to
220 W
(
100 W
on 577).
6. Set
Polarity
to
(+).
7. Set
Left-Right Terminal Jack Selector
to correspond with
location of test fixture.
8. Increase
Variable Collector Supply Voltage
until current
reaches 20 A.
WARNING: Limit test time to 15 seconds maximum.
To measure V
FM
, follow along horizontal scale to the point where
the trace crosses the 20 A axis. The distance from the left-hand
side of scale to the crossing point is the V
FM
value.
(Figure AN1006.4)
Note: Model 370 current is limited to 10 A.
VRRM
IRM
100
nA
100
V
PER
V
E
R
T
DIV
PER
H
O
R
I
Z
DIV
PER
S
T
E
P
()k
DIV
9m
PER
DIV
SOCKET
SOCKET PINS
One set of
pins wired to
Collector (C),
Base (B), and
Emitter (E)
Terminals
The pins which correspond to
the anode and cathode of the
device are wired to the terminals
marked C
SENSE
(MT2/Anode) and
E
SENSE
(MT1/Cathode). The gate
does not require a Kelvin
connection.
Socket used
must have two
sets of pins
相關PDF資料 |
PDF描述 |
|---|---|
| AC25D1FL | HEAT SINK, TO-220/218, 13 C/W; Case style:TO-220 / TO-218; Thermal resistance:13(degree C)/W; Width, external:34.5mm; Depth, external:25mm; Length / Height, external:12.5mm; Material:Aluminium; Surface finish:Black Anodised; Centres, RoHS Compliant: Yes |
| AC25E1FL | HEAT SINK, TO-220/218, 13 C/W; Case style:TO-220 / TO-218; Thermal resistance:13(degree C)/W; Width, external:34.5mm; Depth, external:25mm; Length / Height, external:12.5mm; Material:Aluminium; Surface finish:Black Anodised; Centres, RoHS Compliant: Yes |
| AC25F1FL | HEAT SINK, TO-220/218, 13 C/W; Case style:TO-202; Thermal resistance:13(degree C)/W; Width, external:34.5mm; Depth, external:25mm; Length / Height, external:12.5mm; Material:Aluminium; Surface finish:Black Anodised; Centres, RoHS Compliant: Yes |
| AC03DGM | 3A MOLD TRIAC |
| AC03FGM | Circular Connector; No. of Contacts:6; Series:JTPQ00R; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:16; Circular Contact Gender:Pin; Circular Shell Style:Wall Mount Receptacle; Insert Arrangement:16-6 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AC25BAN100 | 制造商:DISTRIBUTED BY MCM 功能描述:BRITELITE SPEAKER CABLE |
| AC25C-N02G-SV-18JRZ | 制造商:SMC Corporation of America 功能描述:F/MS/R COMBO MODULAR, 1/4INCH W/ GAUGE |
| AC25D1FL | 制造商:TECCOR 制造商全稱:TECCOR 功能描述:Thyristor Product Catalog |
| AC25F1FL | 制造商:TECCOR 制造商全稱:TECCOR 功能描述:Thyristor Product Catalog |
| AC25-N02DE-Z | 制造商:SMC Corporation of America 功能描述:Filter, Regulator & Lubricator, 150 PSI max, 1/4NPT ports, auto drain, press gauge |
發布緊急采購，3分鐘左右您將得到回復。