- 您現在的位置：買賣IC網 > PDF目錄375223 > AAT4626IHS-1-B1 (Advanced Analogic Technologies, Inc.) USB Dual-Channel Power Switch PDF資料下載
參數資料
| 型號： | AAT4626IHS-1-B1 |
| 廠商： | Advanced Analogic Technologies, Inc. |
| 英文描述： | USB Dual-Channel Power Switch |
| 中文描述： | 的USB雙通道電源開關 |
| 文件頁數： | 10/14頁 |
| 文件大小： | 373K |
| 代理商： | AAT4626IHS-1-B1 |
PCB Layout Information
In order to obtain the maximum performance from
the AAT4626, very careful attention must be con-
sidered in regard to the printed circuit board layout.
In most port power switch and port protection appli-
cations, high voltage and current transient events
will occur. Proper printed circuit board (PCB) lay-
out can help reduce the effects of transient events.
PCB trace resistance will effect over all circuit tran-
sient response, in addition small voltage drops will
be incurred.
Refer to the following guidelines for power port
PCB layout:
1.
PCB traces should be kept as short and direct
as possible to minimize the effects of the PCB
on circuit performance.
2.
Make component solder pads large to mini-
mize contact resistance
The AAT4626 output bulk capacitors and fer-
rite beads should be placed as close to the
device as possible. PCB traces to the output
connector should be kept as short as possible
to minimized trace resistance and the associ-
ated voltage drop (I2R loss).
If ferrite beads are used in the circuit, select
ferrite beads with a minimum series resistance.
The use of PCB trace vias should be avoided
on all traces that conduct high currents. If
vias are necessary, make the vias as large as
possible and use multiple vias connected in
parallel to minimize their effect.
3.
4.
5.
AAT4626
USB Dual-Channel Power Switch
10
4626.2002.1.0.93
Figure 3: Summary of typical circuit voltage drops caused by AAT4626 circuit components and PCB
trace resistance.
Trace Resistance
0.01ohms
(5mV)
(5mV)
C
BULK
0.1
μ
F
C
BULK
0.1
μ
F
Cable, Connector
and Contact
Resistance
0.03ohms
(15mV)
(15mV)
V+
GND
Input
Power Supply
4.50V to 5.25V
P-Channel Mosfet
Switch On Resistance
0.09ohms
(45mV)
AAT4626
Ch. A
Ferrite Bead
and PCB trace
resistance
0.02ohms
(10mV)
(10mV)
V
BUS
GND
Downstream
Peripheral Port
500mA Max.
Load Current
Total Voltage Drop = 75mV
OUTA
IN
GND
Evaluation Board Layout
The AAT4626 evaluation layout follows the recom-
mend printed circuit board layout procedures and
can be used as an example for good application
layouts. Note that ferrite beards are not used on
this simple device evaluation board. The board
layout shown is not to scale.
相關PDF資料 |
PDF描述 |
|---|---|
| AAT4626IHS-1-T1 | USB Dual-Channel Power Switch |
| AAT4626IAS-1-T1 | USB Dual-Channel Power Switch |
| AAT4626IAS-B1 | USB Dual-Channel Power Switch |
| AAT4626IAS-T1 | USB Dual-Channel Power Switch |
| AAT4626IHS-B1 | USB Dual-Channel Power Switch |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AAT4626IHS-1-T1 | 制造商:Skyworks Solutions Inc 功能描述:AAT4626 Series 130 mOhm 1.25 A SMT USB Dual-Channel Power Switch - TSSOP-8 制造商:Skyworks Solutions Inc 功能描述:Power Switch ICs - USB USB Dual-Channel Power Switch |
| AAT4626IHS-B1 | 制造商:ANALOGICTECH 制造商全稱:Advanced Analogic Technologies 功能描述:USB Dual-Channel Power Switch |
| AAT4626IHS-T1 | 制造商:ANALOGICTECH 制造商全稱:Advanced Analogic Technologies 功能描述:USB Dual-Channel Power Switch |
| AAT4631IDH-T1 | 制造商:Skyworks Solutions Inc 功能描述:POWER MOSFET TRANSISTOR |
| AAT4644 | 制造商:ANALOGICTECH 制造商全稱:Advanced Analogic Technologies 功能描述:4-Channel Current Limited Load Switch |
發布緊急采購，3分鐘左右您將得到回復。