- 您現在的位置：買賣IC網 > PDF目錄382829 > AAT4625IKS-1-T1 (Advanced Analog Technology,lnc.) USB Single-Channel Power Switch PDF資料下載
參數資料
| 型號： | AAT4625IKS-1-T1 |
| 廠商： | Advanced Analog Technology,lnc. |
| 英文描述： | USB Single-Channel Power Switch |
| 中文描述： | 的USB單通道電源開關 |
| 文件頁數： | 10/15頁 |
| 文件大?。?/td> | 396K |
| 代理商： | AAT4625IKS-1-T1 |
AAT4625
USB Single-Channel Power Switch
10
4625.2006.04.1.2
Reverse Voltage
The AAT4625 is designed to control current flowing
from IN to OUT. If a voltage is applied to OUT
which is greater than that on IN, a large reverse
current may flow, potentially damaging the device.
Under-Voltage Lockout
The AAT4625 has been designed with an under-volt-
age lockout control circuit. The under-voltage lock-
out prevents the output MOSFET device from turn-
ing on until V
IN
exceeds the typical UVLO threshold
of 2.3V. During operation, the device will automati-
cally shut down if V
IN
falls below the UVLO threshold
and the fault flag will be toggled.
Hot-Plug Applications
Application circuit cards with a high inrush current
potential can be limited by use of the AAT4625.
The AAT4625 has both slew rate limited turn-on
characteristics and a current limit controlled output
which make it ideally suited for power port hot-plug
applications. A host power back plane or hot-plug
receptacle may be sensitive to short duration, high
power surges. The AAT4625 will turn on in a linear
ramping fashion and regulate the inrush current
within the specified current limit for the device. The
error flag usually will not be affected during appli-
cation turn-on, since the 10ms flag blanking time is
intended for these types of events. If an application
turn-on current surge exceeds 10ms, an RC delay
filter may be added to the flag output to prevent the
system from receiving an error during the start-up
sequence (see Figure 2).
Figure 2: AAT4625 Inrush Current Protected Application.
0.1
μ
F
AAT4625
1
2
3
4
5
6
7
8
EN
FLG
GND
NC
NC
OUT
IN
OUT
C
BULK
(120
μ
F)
Card
Application
Circuit
v+
GND
Inrush Current Protected
Application Card
Cable / Connector
to Hot-Plug Port
V
BUS
GND
Hot-Plug
Receptacle
PCB Layout Information
In order to obtain maximum performance from the
AAT4625, very careful consideration must be given
to the printed circuit board layout. In most port
power switch and port protection applications, high
voltage and current transient events will occur.
Proper PCB layout can help reduce the effects of
transient events. PCB trace resistance will affect
overall circuit transient response; in addition, small
voltage drops will be incurred.
相關PDF資料 |
PDF描述 |
|---|---|
| AAT4625IKS-T1 | USB Single-Channel Power Switch |
| AAT4670IWP-T1 | Dual-Input, Dual-Output Load Switch |
| AAT4900IJS-T1 | Buffered Power Half-Bridge |
| ABB3007 | GT 3C 3#16 SKT PLUG |
| ABB3007QC-T | High Speed Translator Buffer to CMOS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AAT4625IKS-T1 | 制造商:Skyworks Solutions Inc 功能描述:USB 1-CH PWR SW, AL EN 8MSOP TR 制造商:Skyworks Solutions Inc 功能描述:AAT4625 Series 100 mOhm 2 A SMT USB Single-Channel Power Switch - MSOP-8 制造商:Skyworks Solutions Inc 功能描述:POWER MOSFET TRANSISTOR |
| AAT4626 | 制造商:ANALOGICTECH 制造商全稱:Advanced Analogic Technologies 功能描述:USB Dual-Channel Power Switch |
| AAT4626_08 | 制造商:ANALOGICTECH 制造商全稱:Advanced Analogic Technologies 功能描述:USB Dual-Channel Power Switch |
| AAT4626IAS-1-B1 | 制造商:ANALOGICTECH 制造商全稱:Advanced Analogic Technologies 功能描述:USB Dual-Channel Power Switch |
| AAT4626IAS-1-DB1 | 制造商:Advanced Analogic Tech 功能描述:AAT4626 Series 5.5 V USB Dual-Channel Power Switch Evaluation Board 制造商:SKYWORKS SOLUTIONS 功能描述:AAT4626 Series 5.5 V USB Dual-Channel Power Switch Evaluation Board |
發布緊急采購，3分鐘左右您將得到回復。