- 您現在的位置：買賣IC網 > PDF目錄382829 > AAT4295 (Advanced Analog Technology,lnc.) Single/Dual RGB Controller PDF資料下載
參數資料
| 型號： | AAT4295 |
| 廠商： | Advanced Analog Technology,lnc. |
| 英文描述： | Single/Dual RGB Controller |
| 中文描述： | 單/雙RGB控制器 |
| 文件頁數： | 11/16頁 |
| 文件大?。?/td> | 240K |
| 代理商： | AAT4295 |
Application Information
External Component Selection
The AAT4295 and AAT4297 have been designed
so that no external parts are required for the device
to function as a general purpose three- or six-posi-
tion low-side switch. For some applications, the
addition of bypass capacitors or pull-up or pull-
down resistors may be desired to improve overall
system performance.
For lighting applications, such as controlling RGB
LEDs, keypad or display backlight LEDs, or photo
flash LEDs, no bypass capacitors are necessary.
For other general purpose load switching applica-
tions which may use some or all of the outputs to
switch light load current levels to application cir-
cuits, good engineering practice would dictate the
use of small bypass capacitors placed on the V
CC
input and each switch connection that is used to
conduct current from the load to ground. The use
of small ceramic capacitors between the input and
output nodes will aid in reducing line and load tran-
sient response effects when the load switch on a
given output is turned on or off.
Input Capacitor
Typically, a 0.1μF capacitor is recommended for
C
IN
in most applications to provide input line tran-
sient response immunity to small changes in the
input supply. A C
IN
capacitor is not required for
basic operation. If used, C
IN
should be located as
close to the device V
IN
pin as practically possible.
There is no specific capacitor equivalent series
resistance (ESR) requirement for C
IN
; however, for
higher current operation, ceramic capacitors are
recommended for C
IN
due to their inherent capabil-
ity over tantalum or aluminum electrolytic capaci-
tors to withstand input current surges from low
impedance sources, such as batteries in portable
devices.
Output Capacitor
For typical applications where the AAT4295/97 is
used for LED lighting control, no output capacitors
are required because the end load is not sensitive
to device turn-on or turn-off transient effects.
For improved load transient response in systems
using the AAT4295/97 for load switching, the addi-
tion of a small output capacitor placed between the
output pins and ground can have a beneficial
effect. A 0.1μF ceramic capacitor is suggested as
a reasonable value for an output capacitor.
The output capacitor has no specific capacitor type
or ESR requirement. If desired, C
OUT
may be
increased to a value greater than 0.1μF without
limit to accommodate any load transient condition
without adversely affecting the device turn-on slew
rate time.
Thermal Considerations
The AAT4295 and AAT4297 are designed to sink a
continuous load current to ground when a respec-
tive switch is enabled via the S
2
Cwire control. The
limiting characteristic for maximum safe operating
load current through a given switch or set of switch-
es is package power dissipation. In order to obtain
high operating currents, careful device layout and
circuit operating conditions must be taken into
account. At any given ambient temperature (T
A
),
the maximum package power dissipation can be
determined by the following equation:
Constants for the AAT4295 are maximum junction
temperature, T
J(MAX)
= 125°C, and package thermal
resistance,
θ
JA
= 225°C/W. Worst case conditions
are calculated at the maximum operating tempera-
P
D(MAX)
=T
J(MAX)
- T
A
θ
JA
AAT4295/97
Single/Dual RGB Controller
4295.2006.03.1.3
11
Figure 3: EN/SET Timing Diagram.
T
H
T
L
T
LAT
T
ON
T
O
T
OFF
Sn
EN/SET
相關PDF資料 |
PDF描述 |
|---|---|
| AAT4295IJS-T1 | Single/Dual RGB Controller |
| AAT4297 | Single/Dual RGB Controller |
| AAT4297ITP-T1 | Single/Dual RGB Controller |
| AAT4625IKS-1-T1 | USB Single-Channel Power Switch |
| AAT4625IKS-T1 | USB Single-Channel Power Switch |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AAT4295IJS-T1 | 功能描述:電源開關 IC - 配電 3-Ch Single RGB Controller RoHS:否 制造商:Freescale Semiconductor 輸出端數量: 開啟電阻（最大值）: 開啟時間（最大值）: 關閉時間（最大值）: 工作電源電壓: 電源電流（最大值）: 最大工作溫度: 安裝風格: 封裝 / 箱體: |
| AAT4296 | 制造商:ANALOGICTECH 制造商全稱:Advanced Analogic Technologies 功能描述:Five/Six Channel Push/Pull I/O Expander |
| AAT4296_06 | 制造商:ANALOGICTECH 制造商全稱:Advanced Analogic Technologies 功能描述:Five/Six Channel Push/Pull I/O Expander |
| aat4296ijs-db1 | 制造商:Skyworks Solutions Inc 功能描述:AAT4296 Series Five Channel Push/Pull I/O Expander Eval Board |
| AAT4296IJS-T1 | 功能描述:電源開關 IC - 配電 Five Channel Push/ Pull I/O Expander RoHS:否 制造商:Freescale Semiconductor 輸出端數量: 開啟電阻（最大值）: 開啟時間（最大值）: 關閉時間（最大值）: 工作電源電壓: 電源電流（最大值）: 最大工作溫度: 安裝風格: 封裝 / 箱體: |
發布緊急采購，3分鐘左右您將得到回復。