參數資料
型號： AAT3174IWP-T1
廠商： Advanced Analogic Technologies, Inc.
英文描述： High Current, High Efficiency Charge Pump
中文描述： 大電流，高效率電荷泵
文件頁數： 12/14頁
文件大小： 285K
代理商： AAT3174IWP-T1
AAT3174
High Current, High Efficiency Charge Pump
12
3174.2006.05.1.2
Device Power Efficiency
The AAT3174 power conversion efficiency
depends on the charge pump mode. By definition,
device efficiency is expressed as the output power
delivered to the LED divided by the total input
power consumed.
When the input voltage is sufficiently greater than
the LED forward voltage, the device optimizes effi-
ciency by operating in 1X mode. In 1X mode, the
device is working as a bypass switch and passing
the input supply directly to the output. The power
conversion efficiency can be approximated by,
Due to the very low 1X mode quiescent current, the
input current nearly equals the current delivered to
the LED. Further, the low-impedance bypass
switch introduces negligible voltage drop from input
to output.
The AAT3174 further maintains optimized perform-
ance and efficiency by detecting when the input
voltage is not sufficient to sustain LED current. The
device automatically switches to 1.5X mode when
the input voltage drops too low in relation to the
LED forward voltage.
In 1.5X mode, the output voltage can be boosted to
3/2 the input voltage. The 3/2 conversion ratio
introduces a corresponding 1/2 increase in input
current. For ideal conversion, the 1.5X mode effi-
ciency is given by:
Similarly, when the input falls further, such that
1.5X mode can no longer sustain LED current, the
device will automatically switch to 2X mode. In 2X
mode, the output voltage can be boosted to twice
the input voltage. The doubling conversion ratio
introduces a corresponding doubling of the input
current. For ideal conversion, the 2X mode effi-
ciency is given by:
LED Selection
The AAT3174 is designed to drive high-intensity white
LEDs. It is particularly suitable for LEDs with an oper-
ating forward voltage in the range of 4.2V to 1.5V.
The charge pump device can also drive other loads
that have similar characteristics to white LEDs. For
various load types, the AAT3174 provides a high-cur-
rent, programmable ideal constant current source.
Capacitor Selection
Careful selection of the four external capacitors
C
IN
, C
1
, C
2
, and C
OUT
is important because they will
affect turn-on time, output ripple, and transient per-
formance. Optimum performance will be obtained
when low equivalent series resistance (ESR)
ceramic capacitors are used. In general, low ESR
may be defined as less than 100m
Ω
. A value of
1μF for the flying capacitors is a good starting point
when choosing capacitors. If the LED current sinks
are only programmed for light current levels, then
the capacitor size may be decreased.
Ceramic composition capacitors are highly recom-
mended over all other types of capacitors for use
with the AAT3174. Ceramic capacitors offer many
advantages over their tantalum and aluminum elec-
trolytic counterparts. A ceramic capacitor typically
has very low ESR, is lowest cost, has a smaller
PCB footprint, and is non-polarized. Low ESR
ceramic capacitors help maximize charge pump
transient response. Since ceramic capacitors are
non-polarized, they are not prone to incorrect con-
nection damage.
Equivalent Series Resistance
ESR is an important characteristic to consider
when selecting a capacitor. ESR is a resistance
internal to a capacitor that is caused by the leads,
internal connections, size or area, material compo-
sition, and ambient temperature. Capacitor ESR is
typically measured in milliohms for ceramic capac-
η
=
=
V
F
· I
LED
V
IN
· 2I
IN
V
F
2 · V
IN
η
=
=
V
F
· I
LED
V
IN
· 1.5I
IN
V
F
1.5 · V
IN
η
=
≈
V
F
· I
LED
V
IN
· I
IN
V
F
V
IN
η
= P
OUT
P
IN
相關PDF資料
PDF描述
AAT3175 High Efficiency 1X/1.5X/2X Charge Pump For White LED Flash Applications
AAT3175IWP-T1 High Efficiency 1X/1.5X/2X Charge Pump For White LED Flash Applications
AAT3183 300mA Inductorless Step-Down Converter
AAT3183IJS-1.5-T1 300mA Inductorless Step-Down Converter
AAT3190 Positive/Negative Charge Pump for Voltage Bias
相關代理商/技術參數
參數描述
AAT3175 制造商:ANALOGICTECH 制造商全稱:Advanced Analogic Technologies 功能描述:High Efficiency 1X/1.5X/2X Charge Pump For White LED Flash Applications
AAT3175IWP-T1 制造商:Skyworks Solutions Inc 功能描述:LED Lighting Drivers High Efficiency Charge Pump
AAT3176AIDH-T1 制造商:Skyworks Solutions Inc 功能描述:IC LED DRVR FLASH 10TDFN 制造商:Advanced Analogic Tech 功能描述:AAT3176 Series 500 mA 5.5 V 1.5 MHz LED Photo Flash LED Driver IC - TDFN-10 制造商:Skyworks Solutions Inc 功能描述:LED DRIVER IC
AAT3176IDH-T1 制造商:SKYWORKS SOLUTIONS INC 功能描述:500MA FLASH DRIVER IC 10TDFN TR
AAT3177 制造商:ANALOGICTECH 制造商全稱:Advanced Analogic Technologies 功能描述:High Current, High Efficiency Charge Pump with Auto-Timer
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*