- 您現在的位置：買賣IC網 > PDF目錄375166 > AAT3142ITP-T1 (Advanced Analogic Technologies, Inc.) High Efficiency 1X/1.5X/2X Charge Pump for White LED Applications PDF資料下載
參數資料
| 型號： | AAT3142ITP-T1 |
| 廠商： | Advanced Analogic Technologies, Inc. |
| 英文描述： | High Efficiency 1X/1.5X/2X Charge Pump for White LED Applications |
| 中文描述： | 高效率1x/1.5x/2x電荷泵白光LED應用 |
| 文件頁數： | 10/16頁 |
| 文件大?。?/td> | 425K |
| 代理商： | AAT3142ITP-T1 |
AAT3142
High Efficiency 1X/1.5X/2X Charge Pump
for White LED Applications
10
3142.2005.12.1.1
Functional Block Diagram
1X
1.5X
2X
Charge
Pump
Soft-Start
Control
1MHz
Oscillator
Voltage
Reference
32 x 8 bit
ROM
C1+
C1-
C2+
C2-
CP
D1
D2
D3
GND
EN/SET
VIN
S
2
Cwire
Interface
D/A
D/A
D/A
Functional Description
The AAT3142 is a tri-mode load switch (1X) and
high efficiency (1.5X or 2X) charge pump device
intended for white LED backlight applications. To
maximize power conversion efficiency, an internal
sensing circuit monitors the voltage required on
each constant current source output and sets the
load switch and charge pump modes based on the
input battery voltage and the current source output
voltage. As the battery discharges over time, the
AAT3142 charge pump is enabled when any of the
three current source outputs nears dropout. The
charge pump initially starts in 1.5X mode. If the
charge pump output drops enough for any current
source output to become close to dropout, the
charge pump will automatically transition to 2X
mode. Each of the three current source outputs is
independently switched between the battery input
(1X) or the charge pump output (1.5X or 2X),
depending on the voltage at the current source out-
put. Since the LED-to-LED forward voltage (V
F
)
can vary as much as 1V, this function significantly
enhances overall device efficiency when the bat-
tery input voltage level is greater than the voltage
required at any current source output.
The AAT3142 requires only four external compo-
nents: two 1μF ceramic capacitors for the charge
pump flying capacitors (C
1
and C
2
), one 1μF
ceramic input capacitor (C
IN
), and one 0.33μF to
1μF ceramic charge pump output capacitor (C
CP
).
The three constant current outputs (D1 to D3) drive
three individual LEDs with a maximum current of
30mA each. The EN/SET S
2
Cwire serial interface
enables the AAT3142 and sets the current source
magnitudes.
相關PDF資料 |
PDF描述 |
|---|---|
| AAT3151B | High Efficiency 1X/1.5X Charge Pump For White LED Applications |
| AAT3151BIWP-T1 | High Efficiency 1X/1.5X Charge Pump For White LED Applications |
| AAT3151 | High Efficiency 1X/1.5X/2X Charge Pump For White LED Applications |
| AAT3151IWP-T1 | High Efficiency 1X/1.5X/2X Charge Pump For White LED Applications |
| AAT3152 | High Efficiency 1X/1.5X/2X Charge Pump For White LED Applications |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AAT3143 | 制造商:ANALOGICTECH 制造商全稱:Advanced Analogic Technologies 功能描述:High Efficiency 1X/1.5X/2X Charge Pump with PWM Control for White LED Applications |
| AAT3143ITP-T1 | 制造商:Skyworks Solutions Inc 功能描述:2X,1.5X,1X WLED CHPMP, TSOPJW-12 TR |
| AAT3150AIWP-T1 | 制造商:SKYWORKS SOLUTIONS INC 功能描述:1X/1.5X/2X CHPUMP FOR WHITE LED TR |
| AAT3150IWP-T1 | 制造商:SKYWORKS SOLUTIONS INC 功能描述:1X/1.5X WLED CHPMP,TDFN33-12 TR |
| AAT3151 | 制造商:AAT 制造商全稱:AAT 功能描述:High Efficiency 1X/1.5X/2X Charge Pump For White LED Applications |
發布緊急采購，3分鐘左右您將得到回復。