- 您現在的位置：買賣IC網 > PDF目錄382828 > AAT1232ITP-T1 (Advanced Analog Technology,lnc.) 24V 100mA Step-Up Converter PDF資料下載
參數資料
| 型號： | AAT1232ITP-T1 |
| 廠商： | Advanced Analog Technology,lnc. |
| 英文描述： | 24V 100mA Step-Up Converter |
| 中文描述： | 24V的100mA的升壓轉換器 |
| 文件頁數： | 12/17頁 |
| 文件大?。?/td> | 416K |
| 代理商： | AAT1232ITP-T1 |
AAT1232
24V 100mA Step-Up Converter
12
1232.2006.12.1.3
RMS calculation yields worst-case inductor loss.
The RMS value should be compared against the
manufacturer's temperature rise, or thermal derat-
ing, guidelines.
For a given inductor type, smaller inductor size leads
to an increase in DCR winding resistance and, in
most cases, increased thermal impedance. Winding
resistance degrades boost converter efficiency and
increases the inductor operating temperature.
To ensure high reliability, the inductor temperature
should not exceed 100oC. Manufacturer's recom-
mendations should be consulted. In some cases,
PCB heatsinking applied to the AAT1232 L
IN
node
(non-switching) can improve the inductor's thermal
capability. PCB heatsinking may degrade EMI per-
formance when applied to the SW node (switching)
of the AAT1232.
Shielded inductors provide decreased EMI and
may be required in noise sensitive applications.
Unshielded chip inductors provide significant space
savings at a reduced cost compared to shielded
(wound and gapped) inductors. Chip-type induc-
tors have increased winding resistance when com-
pared to shielded, wound varieties.
Setting the Output Voltage
The output voltage may be programmed through a
resistor divider network located from the output to
FB1 and FB2 pins to ground. Pulling the SEL pin
high activates the FB1 pin which maintains a 1.2V
reference voltage, while the FB2 reference is dis-
abled. Pulling the SEL pin low activates the FB2
pin which maintains a 0.6V reference, while the
FB1 reference is disabled.
The AAT1232 output voltage can be programmed
by one of three methods. First, the output voltage
can be static by pulling the SEL logic pin either high
or low. Second, the output voltage can be dynam-
ically adjusted between two pre-set levels within a
2X operating range by toggling the SEL logic pin.
Third, the output can be dynamically adjusted to
any of 16 preset levels within a 2X operating range
using the integrated S
2
Cwire single wire interface
via the EN/SET pin.
Option 1: Static Output Voltage
A static output voltage can be configured by pulling
the SELeither high or low. SELpin high activates the
FB1 reference pin to 1.2V (nominal). Alternatively,
the SEL pin is pulled low to activate the FB2 refer-
ence at 0.6V (nominal). Table 1 provides details of
resistor values for common output voltages from 10V
to 24V for SEL = High and SEL = Low options.
In the static configuration, the FB1 pin should be
directly connected to FB2. The resistor between
FB1 and FB2 pins is not required.
Option 2: Dynamic Voltage Control Using SEL Pin
The output may be dynamically adjusted between
two output voltages by toggling the SEL logic pin.
Output voltages V
OUT(1)
and V
OUT(2)
correspond to
the two output references, FB1 and FB2. Pulling
the SEL logic pin high activates V
OUT(1)
, while
pulling the SEL logic pin low activates V
OUT(2)
.
The minimum output voltage must be greater than
the specified maximum input voltage plus margin to
maintain proper operation of the AAT1232 boost
converter. In addition, the ratio of output voltages
V
OUT(2)
/V
OUT(1)
is always less than 2.0, correspon-
ding to a 2X (maximum) programmable range.
Table 1 is provided to allow programming of com-
mon output voltages using Option 1 or 2. The feed-
back references FB1 and FB2 are enabled or dis-
abled using the SEL logic pin, corresponding to
V
OUT(1)
and V
OUT(2)
.
Option 3: Dynamic Voltage Control Using
S
2
Cwire Interface
The output can be dynamically adjusted by the host
controller to any of 16 pre-set output voltage levels
using the integrated S
2
Cwire interface. The
EN/SET pin serves as the S
2
Cwire interface input.
The SEL pin must be pulled low when using the
S
2
Cwire interface.
P
LOSS_INDUCTOR
= I
RMS2
· DCR
I
PEAK
3
I
RMS
=
相關PDF資料 |
PDF描述 |
|---|---|
| AAT1265 | Low Voltage 2MHz Step-Up DC/DC Converter in SC70JW Package |
| AAT1265_0606 | Low Voltage 2MHz Step-Up DC/DC Converter in SC70JW Package |
| AAT1265IJS-3.0-T1 | Low Voltage 2MHz Step-Up DC/DC Converter in SC70JW Package |
| AAT1265IJS-3.3-T1 | Low Voltage 2MHz Step-Up DC/DC Converter in SC70JW Package |
| AAT1265IJS-3.6-T1 | Low Voltage 2MHz Step-Up DC/DC Converter in SC70JW Package |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AAT1235 | 制造商:ANALOGICTECH 制造商全稱:Advanced Analogic Technologies 功能描述:High Efficiency White LED Drivers for Backlight and Keypad |
| AAT1235IRN-T1 | 制造商:ANALOGICTECH 制造商全稱:Advanced Analogic Technologies 功能描述:High Efficiency White LED Drivers for Backlight and Keypad |
| AAT1236 | 制造商:AAT 制造商全稱:AAT 功能描述:High Efficiency White LED Drivers for Backlight and Keypad |
| AAT1236IRN-T1 | 制造商:Skyworks Solutions Inc 功能描述:24V 100MASTEPUP CONVERTER TDFN34 TR 制造商:Skyworks Solutions Inc 功能描述:DC TO DC CONVERTER |
| AAT1239-1 | 制造商:ANALOGICTECH 制造商全稱:Advanced Analogic Technologies 功能描述:40V Step-Up Converter for 4 to 10 White LEDs |
發布緊急采購，3分鐘左右您將得到回復。