參數資料
型號： AAT1230
廠商： Advanced Analogic Technologies, Inc.
英文描述： 18V 100mA Step-Up Converter
中文描述： 18V的100mA的升壓轉換器
文件頁數： 9/21頁
文件大小： 491K
代理商： AAT1230
AAT1230
18V 100mA Step-Up Converter
1230.2006.03.1.0
9
The magnitude of the feedback error signal deter-
mines the average input current. Therefore, the
AAT1230 controller implements a programmed
current source connected to the output capacitor
and load resistor. There is no right-half plane zero,
and loop stability is achieved with no additional
compensation components.
Increased load current results in a drop in the out-
put feedback voltage (FB1 or FB2) sensed through
the feedback resistors (R1, R2, R3). The controller
responds by increasing the peak inductor current,
resulting in higher average current in the inductor.
Alternatively, decreased output load results in an
increase in the output feedback voltage (FB1 or
FB2 pin). The controller responds by decreasing
the peak inductor current, resulting in lower aver-
age current in the inductor.
At light load, the inductor OFF interval current goes
below zero and the boost converter enters discon-
tinuous mode operation. Further reduction in the
load results in a corresponding reduction in the
switching frequency. The AAT1230 provides pulsed
frequency operation which reduces switching loss-
es and maintains high efficiency at light loads.
Operating frequency varies with changes in the
input voltage, output voltage, and inductor size.
Once the boost converter has reached continuous
mode, further increases in the output load will not
significantly change the operating frequency. A
small 2.2μH (±20%) inductor is selected to maintain
high frequency switching (up to 2MHz) and high
efficiency operation for outputs from 10V to 18V.
Output Voltage Programming
The output voltage may be programmed through a
resistor divider network located from output capaci-
tor to FB1/FB2 pins to ground. Pulling the SEL pin
high activates the FB1 pin which maintains a 1.2V
reference voltage, while the FB2 reference is dis-
abled. Pulling the SELpin low activates the FB2 pin
which maintains a 0.6V reference, while the FB1
reference is disabled. This function allows dynam-
ic selection between two distinct output voltages
across a 2X range (maximum). An additional resis-
tor between FB1 and FB2 allows the designer to
program the outputs across a reduced <2X range.
Alternatively, the output voltage may be dynamical-
ly programmed to any of 16 voltage levels using the
S
2
Cwire serial digital input. The single wire S
2
Cwire
interface provides high-speed output voltage pro-
grammability across a 2X output voltage range.
S
2
Cwire functionality is enabled by pulling the SEL
pin low and providing S
2
Cwire digital clock input to
the EN/SET pin. Table 2 details the FB2 reference
voltage versus S
2
Cwire rising clock edges.
Soft Start / Enable
The input disconnect switch is activated when a
valid input voltage is present and the EN/SET pin
is pulled high. The slew rate control on the P-chan-
nel MOSFET ensures minimal inrush current as
the output voltage is charged to the input voltage,
prior to switching of the N-channel power MOS-
FET. Monotonic turn-on is guaranteed by the built-
in soft-start circuitry. Soft-start eliminates output
voltage overshoot across the full input voltage
range and all loading conditions.
Current Limit and Over-Temperature
Protection
The switching of the N-channel MOSFET termi-
nates when current limit of 3.0A (typical) is exceed-
ed. This minimizes power dissipation and compo-
nent stresses under overload and short-circuit con-
ditions. Switching resumes when the current
decays below the current limit.
Thermal protection disables the AAT1230 when
internal dissipation becomes excessive. Thermal
protection disables both MOSFETs. The junction
over-temperature threshold is 140°C with -15°C of
temperature hysteresis. The output voltage auto-
matically recovers when the over-temperature or
over-current fault condition is removed.
Under-Voltage Lockout
Internal bias of all circuits is controlled via the V
IN
input. Under-voltage lockout (UVLO) guarantees
sufficient V
IN
bias and proper operation of all inter-
nal circuitry prior to soft start.
相關PDF資料
PDF描述
AAT1239-1 40V Step-Up Converter for 4 to 10 White LEDs
AAT1239ITP-1-T1 40V Step-Up Converter for 4 to 10 White LEDs
AAT1265 Low Voltage 2MHz Step-Up DC/DC Converter in SC70JW Package
AAT1265IJS-3.3-T1 Low Voltage 2MHz Step-Up DC/DC Converter in SC70JW Package
AAT1270 1A Step-Up Current Regulator for Flash LEDs
相關代理商/技術參數
參數描述
AAT1230_0610 制造商:ANALOGICTECH 制造商全稱:Advanced Analogic Technologies 功能描述:18V 100mA Step-Up Converter
AAT1230_07 制造商:ANALOGICTECH 制造商全稱:Advanced Analogic Technologies 功能描述:18V 100mA Step-Up Converter
AAT1230-1 制造商:ANALOGICTECH 制造商全稱:Advanced Analogic Technologies 功能描述:18V 100mA Step-Up Converter
AAT1230IRN 制造商:ANALOGICTECH 制造商全稱:Advanced Analogic Technologies 功能描述:18V 100mA Step-Up Converter
AAT1230IRN-1-T1 制造商:SKYWORKS SOLUTIONS INC 功能描述:IC REG BOOST ADJ .1A 16TDFN TR 制造商:Skyworks Solutions Inc 功能描述:DC TO DC CONVERTER
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*