參數資料
型號: A8L-11-15N2
元件分類: 開關
英文描述: ROCKER SWITCH, SPST, LATCHED, PANEL MOUNT
文件頁數: 4/4頁
文件大?。?/td> 673K
代理商: A8L-11-15N2
4
A8L
Panel Cutout
Note:
Recommended panel material: SPCC
Panel Cutout for Angled PCB Terminals
(A8L-
@@ @ @@, A8L-@@-@4)
Be sure that play R is the operation side.
Precautions
!Caution
Do not wire the Switch or touch any terminal of the Switch while
power is being supplied. Doing so may result in electric shock.
To increase the reliability of operation, test the Switch before
actual operation.
Be sure that there is an enough insulation distance between any
Switch terminal and metal part.
Mounting
Turn OFF the power supply before mounting, removing or wiring
the Switch, or before performing maintenance inspections. Failure
to do so may result in electric shock.
Do not use panels other than ones with the designated thickness
and dimensions. Remove all burrs from the cutout before install-
ing the Switch. Otherwise, the Switch may malfunction.
Do not impose excessive force on the Switch at the time of panel-
mounting.
There are two small divots in the flange part of the case marking
ON and OFF as shown in the following diagram. Use these marks
as guides when mounting.
Wiring
When soldering terminals manually, perform soldering within 3 s
using a 60-W soldering iron (temperature at the tip of the solder-
ing iron: 420
°C max.). Do not apply excessive force to the termi-
nals during soldering.
When soldering using a soldering tub, perform soldering within 5
s in a soldering fluid at 270
°C, or within 3 s in a soldering fluid at
350
°C.
Be sure that the wires are thick enough for the load (current) to be
applied.
The performance of the Switch may be affected if the Switch is
used for switching micro loads. Test the Switch under the actual
operating conditions.
Only A8L-
- 5
models are equipped with (6.3
×0.8) mm
flat-quick connections for use with #187 fasten receptacles.
The terminals of A8L-
- 1
are not in compliance with IEC
standards for flat-quick connections. Suitable for use as solder
connection only.
Operating Environment
sea breeze, oil spray, or direct sunlight. Otherwise, the Switch
may malfunction.
Do not use the Switch in places that are visibly dusty. Otherwise,
the contacts may fail to operate correctly.
Handling
Panel thickness (mm)
X (mm)
Y (mm)
X
Y
19.2
0
0.1
12.9 +0.1
0
19.4
+0.1
0.3
12.9 +0.1
0
Play R
Edge
0.75 to 1.25
1.26 to 2.5
15
±0.3
17.5
±0.3
X
12.9 0.1
0
19.2 0.1
0
19.4 0.3
+0.1
ON
OFF
In the interest of product improvement, specifications are subject to change without notice.
ALL DIMENSIONS SHOWN ARE IN MILLIMETERS.
Cat. No. A114-E1-03
OMRON Corporation
Electronic Components Company
Electronic & Mechanical Components Division H.Q.
Speciality Switch Department
Shiokoji Horikawa, Shimogyo-ku,
Kyoto, 600-8530 Japan
Tel: (81)75-344-7096/Fax: (81)75-344-7049
Printed in Japan
0405-?M (0200) (?)
相關PDF資料
PDF描述
A8ND-3162 ROCKER SWITCH, DPST, LATCHED, PANEL MOUNT
A918CY-470M 1 ELEMENT, 47 uH, FERRITE-CORE, GENERAL PURPOSE INDUCTOR, SMD
A918CY-390M 1 ELEMENT, 39 uH, FERRITE-CORE, GENERAL PURPOSE INDUCTOR, SMD
A920CY-101M 1 ELEMENT, 100 uH, GENERAL PURPOSE INDUCTOR, SMD
AA-122-14 1.5 mm2, COPPER ALLOY, TIN FINISH, RING TERMINAL
相關代理商/技術參數
參數描述
A8L-11-15N3 制造商:OMRON 制造商全稱:Omron Electronics LLC 功能描述:Miniature Rocker Switch
A8L-11-15N6 制造商:OMRON 制造商全稱:Omron Electronics LLC 功能描述:Miniature Rocker Switch
A8L2111N1 制造商:Omron Electronic Components LLC 功能描述:SWIT RCKR ON OFF DPST SLDR RCKR 10A 250VAC 50000CYCLE - Trays 制造商:Omron Electronic Components LLC 功能描述:SWITCH ROCKER MINI DPST VERT SLD 制造商:Omron Electronic Components LLC 功能描述:Switch Rocker ON OFF DPST Solder Curved Rocker 10A 250VAC 50000Cycle Box
A8L-21-11N1 功能描述:搖臂開關與扳鈕開關 MINIATURE ROCKER SWITCH FOR HI CRRNT RoHS:否 制造商:C&K Components 觸點形式: 開關功能: 電流額定值:50 mA 電壓額定值 AC: 電壓額定值 DC:30 V 功率額定值: 端接類型: 執(zhí)行器:Paddle 顏色: 安裝風格:Panel 端子密封: 觸點電鍍: 照明:Not Illuminated 照明顏色:
A8L2111N2 制造商:Omron Electronic Components LLC 功能描述:SWIT RCKR ON OFF DPST SLDR RCKR 10A 250VAC 50000CYCLE - Bulk