參數資料
型號： A49LF040ATL-33F
廠商： AMIC Technology Corporation
英文描述： 4 Mbit CMOS 3.3Volt-only Low Pin Count Flash Memory
中文描述： 4兆位的CMOS 3.3Volt只低引腳數快閃記憶體
文件頁數： 2/32頁
文件大小： 622K
代理商： A49LF040ATL-33F
A49LF040A
Preliminary
4 Mbit CMOS 3.3Volt-only Low Pin Count Flash Memory
PRELIMINARY (March, 2006, Version 0.1)
1
AMIC Technology, Corp.
FEATURES
Single Power Supply Operation
-
Low voltage range: 3.0 V - 3.6 V for Read and Write
Operations
Standard Intel Low Pin Count Interface
-
Read compatible to Intel Low Pin Count (LPC)
interface
Memory Configuration
-
512K x 8 (4 Mbit)
Block Architecture
-
4Mbit: eight uniform 64KByte blocks
-
Supports full chip erase for Address/Address
Multiplexed (A/A Mux) mode
Automatic Erase and Program Operation
-
Embedded Byte Program and Block/Chip Erase
algorithms
-
Typical 10 μs/byte programming time
-
Typical 1s block erase time
Two Operational Modes
-
Low Pin Count Interface (LPC) Mode for in-system
operation
-
Address/Address Multiplexed (A/A Mux) Interface
Mode for programming equipment
Low Pin Count (LPC) Mode
-
33 MHz synchronous operation with PCI bus
-
5-signal communication interface for in-system read
and write operations
General Description
The A49LF040A flash memory device is designed to be
read-compatible with the Intel Low Pin Count (LPC) Interface
Specification 1.1. This device is designed to use a single low
voltage, range from 3.0 Volt to 3.6 Volt power supply to
perform in-system or off-system read and write operations. It
provides protection for the storage and update of code and
data in addition to adding system design flexibility through
five general-purpose inputs. Two interface modes are
supported by the A49LF040A: Low Pin Count (LPC) Interface
mode for In-System programming and Address/Address
Multiplexed (A/A Mux) mode for fast factory programming of
PC-BIOS applications.
The memory is divided into eight uniform 64Kbyte blocks that
can be erased independently without affecting the data in
other blocks. Blocks also can be protected individually to
prevent accidental Program or Erase commands from
modifying the memory. The boot block can be write protected
by a hardware method controlled by the
TBL
pin or a
register-based protection turned on/off by the Block Locking
Registers (LPC mode only). The rest of blocks except boot
-
-
-
-
-
-
-
Standard SDP Command Set
Data Polling (I/O
7
) and Toggle Bit (I/O
6
) features
Block Locking Register for all blocks
4 ID pins for multi-chip selection
5 GPI pins for General Purpose Input Register
TBL
pin for hardware write protection to Boot Block
WP
pin for hardware write protection to whole
memory array except Boot Block
Address/Address Multiplexed (A/A Mux) Mode
-
11-pin multiplexed address and 8-pin data I/O interface
-
Supports fast programming on EPROM programmers
-
Standard SDP Command Set
-
Data Polling (I/O
7
) and Toggle Bit (I/O
6
) features
Lower Power Consumption
-
Typical 12mA active read current
-
Typical 24mA program/erase current
High Product Endurance
-
Guarantee 100,000 program/erase cycles for each
block
-
Minimum 20 years data retention
Compatible Pin-out and Packaging
-
32-pin (8 mm x 14 mm) TSOP (TYPE I)
-
32-pin PLCC
-
Optional Pb-free (Lead-free) package
-
All Pb-free (Lead-free) products are RoHS compliant
block in the device also can be write protected by
WP
pin or
Block Locking Registers (LPC mode only). The Program and
Erase operations are executed by issuing the Program/Erase
commands into the command interface by which activating
the internal control logic to automatically process the
Program/Erase procedures. The device can be programmed
on a byte-by-byte basis after performing the Erase operation.
In addition to the Block Erase operation, the Chip Erase
feature is provided in A/A Mux mode that allows the whole
memory to be erased in one single Erase operation. The
A49LF040A provides the status detection such as Data
Polling (I/O
7
) and Toggle Bit (I/O
6
) Functions in both
FWH/LPC and A/A Mux modes. The process or completion
of Program and Erase operations can be detected by reading
the status bits.
The A49LF040A is offered in 32-lead TSOP and 32-lead
PLCC packages with optional environmental friendly lead-
free package. See Figures 1 and 2 for pin assignments and
Table 1 for pin descriptions.
相關PDF資料
PDF描述
A49LF040ATX-33 4 Mbit CMOS 3.3Volt-only Low Pin Count Flash Memory
A49LF040ATX-33F 4 Mbit CMOS 3.3Volt-only Low Pin Count Flash Memory
A49LF040TX-33 240 x 128 pixel format, LED or EL Backlight
A49LF040TX-33F 240 x 128 pixel format, LED or EL Backlight
A49LF040 4 Mbit CMOS 3.3Volt-only Low Pin Count Flash Memory
相關代理商/技術參數
參數描述
A49LF040ATX-33 制造商:AMICC 制造商全稱:AMIC Technology 功能描述:4 Mbit CMOS 3.3Volt-only Low Pin Count Flash Memory
A49LF040ATX-33F 制造商:AMICC 制造商全稱:AMIC Technology 功能描述:4 Mbit CMOS 3.3Volt-only Low Pin Count Flash Memory
A49LF040TL-33 制造商:AMICC 制造商全稱:AMIC Technology 功能描述:4 Mbit CMOS 3.3Volt-only Low Pin Count Flash Memory
A49LF040TL-33F 制造商:AMICC 制造商全稱:AMIC Technology 功能描述:4 Mbit CMOS 3.3Volt-only Low Pin Count Flash Memory
A49LF040TX-33 制造商:AMICC 制造商全稱:AMIC Technology 功能描述:4 Mbit CMOS 3.3Volt-only Low Pin Count Flash Memory
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*